Search Documents

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Emmett J. Ientilucci, Martin Held, Xuesong Liu

Mining is crucial for advancing technology and science by providing essential resources and materials. Quarry blasting, a necessary process in mining, releases these resources and chemicals, driving research and engineering improvements. However, NOx (nitrogen oxides) is an undesired contaminant produced during quarry blasts, posing a significant negative impact on mining activities. Therefore, detecting and quantifying NOx emissions is essential for designing effective blasts, analyzing their dynamics, and reducing contaminant production. Image processing and machine learning, including deep learning methods, have been applied to solve smoke plume detection and segmentation tasks. Most research has focused on smoke from campfires or forest fires, which are important for early fire and smoke detection. However, there is limited research on quarry blast smoke using machine learning methods, which presents challenges for recognizing the smoke plume from complex background scenarios and objects, including collapsed rocks, scattered soil dust and dirt, and the dynamic movement of the scene due to blast vibrations. Detecting NOx within the smoke plumes is further challenging because NOx must be distinguished from the overall smoke plume, as they share many common spatial features. To resolve this issue, we propose an ensemble method for NOx detection that combines smoke plume segmentation with NOx fume detection. First, we apply a smoke plume segmentation model to identify the smoke plume regions. Then, we use these masked-out smoke plume regions to detect NOx based on its unique color features. The first stage of the ensemble method helps block out complicated confusers in the background, such as reddish and brownish dirt. Next, we specifically design a color classifier for NOx to further improve its sensitivity. We evaluate the overall video-wise performance using accuracy, false alarm, and miss rates based on sampled image frames from videos. Additionally, we assess the mean Intersection over Union (mIoU) for smoke plume segmentation and the mean Average Precision (mAP) for image-wise performance from an algorithmic perspective. In summary, this paper represents the first attempt to apply machine learning approaches to NOx detection in a memory-efficient and time-efficient manner.

Jan 21, 2025

By Ann Barron, Mark Abernethy

Regardless of the care exercised by a blaster, seismic and acoustic effects produced by blasting can be disruptive and alarming to many people. With the general trend toward larger blasts, increased population, and urban sprawl, as well as sensational accounts of explosives - related incidents by the news media, fear and concern often leave residents searching for damage to their property. As a result, many blasting companies today find themselves at the center of litigation at an accelerating rate. Obviously, the best strategy for handling vibration and airblast complaints is to operate in a manner that does not create grounds for them in the first place. During the bidding process, ask questions. See the actual site to perf o rm an “exposure analysis.” Collect as many facts as possible before blasting including geological issues, contractual obligations, zoning, historical use of site, disruption of daily life to local residents, demographics of the surrounding area, as well as any unfavorable public opinions or prejudices connected with local construction projects or mining operations. A consultation with local pre-blast firms may assist in tracking down previous problems in the area.

Jan 1, 2004

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By Park McLure, Paul Kunze

Abandoned underground mine workings have been regularly encountered in open pit mining excavations for many years, for the most part without many serious problems resulting. During the last several years however, some tragic occurrences and near misses have resulted when these old workings were intercepted. This paper will report on the problem as it relates to western open pit mining and will describe several techniques that can be used to identify problem areas before they are reached: Utilization of old maps and engineering data, long hole drilling and probing, and the use of subsurface investigation in the form of ground penetrating radar are the detection methods that will be discussed. The paper will describe some possible actions, once potential problem areas are identified. Drilling and blasting crews are usually exposed to the hazards involved when these situations arise because of their "on the ground" working environment. It is therefore appropriate that some of the best methods of dealing with these hazards once they are identified, seems to involve innovative and creative blast designs. The paper will discuss these approaches and describe an example of this aspect of the solution.

Jan 1, 1993

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By N. Rouse

Underground raises and slots are a vital part of underground blasting operations. Raises and slots are vertical shafts or openings used for ventilation, ore passes, or creating voids in stopes. In the author’s experience, raise and slot designs can vary significantly from operation to operation or even within a single operation, sometimes for reasons unknown. The results of the various designs can differ depending on drilling accuracy, geology, and the explosives used in the design. The purpose of this paper is to summarize the recommendations found in published literature on raise and slot design in one document, while incorporating some of the author’s own experience with optimizing raise and slot designs in underground operations. Some inspiration is also included from burn round designs; small versions of raises drilled horizontally in development blasting rounds. This document includes discussion points on drillhole diameter and depth, pattern design and relief requirements, explosive types and loading recommendations, and timing. Ultimately, this document can be useful to those looking to design a raise or slot blast for the first time or for those looking to improve on the results from the raise and slot blasts used at their operations.

Jan 1, 2024

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

By Ron Glowe

This paper shows the potential of a new computer model, using the Glowe-Tech (GT) Tonnage Analyzer program to compare drilling and blasting results. This model uses the crushers and conveyors as measuring tools in aggregate quarries in the USA and Canada. All data is collected using commercially available kilowatt transducers and an analog input/output automation module. There are two areas of measurement used to compare results. The first area is the tonnage moved by key conveyors to show the split in products produced and the actual rate of production. If belt scale readings are not available then the Glowe-Tech Tonnage Analyzer can be used to convert kilowatts from the conveyor motor to tonnage. The second is the tons of rock crushed per kilowatt hour of energy consumption by the primary and secondary (optional) crushers. This modeling process works best if blasts are mucked and crushed in sequence. There are many other variables such as crusher types, crusher settings, screen sizing and actual geology in the pit that can influence the results, however if variables can be standardized then definite trends can be seen when comparing drilling and blasting results

Jan 1, 2005

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By Debra Satkowiak, Ronald Thomas

The Institute of Makers of Explosives (IME), a non-profit safety and security organization founded in 1913, is known for its industry best practices, Safety Library Publications (SLP), some of which have been incorporated into rules by regulatory agencies. The IME developed the first commercial storage, quantity distance (Q/D) table titled “The American Table of Distances” (ATD). It was developed by IME’s legacy association in 1910 and was originally based on observations of structural damage from 117 accidental explosions involving small to very large amounts of explosives, primarily dynamite and black powder. In 1930, the IME published a book, compiled by Ralph Assheton, called the “History of Explosions on Which the American Table of Distances was Based”. The distance in feet in the ATD were founded on the measurements at which inhabited buildings sustained substantial structural damage from the accidental detonation of explosives. For example, minor damage such as window glass breakage and the “shaking down” of plaster was not considered substantial structural damage. Other damage to property that was readily repairable was also not considered “substantial.” It was concluded that unless some integral portion of the building was damaged, the occupants would not be subjected to serious risks.

Jan 1, 2017

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991