Search Documents

By J. W. Snavely

THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show, this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from. field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. I affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1952

By W. B. Morrison

The principal factors influencing the total percent elongation of a lead-tin eutectic and several low-alloy steels which exhibit superplasticity were investigated. These factors are: a) Strain-rate sensitivity of the stress (m). b) Specimen geometry; in particular, diameter-to-length ratio (d0/l0), and surface irregularity (e.g. notches). A feature of the tensile deformation of a superplastic alloy is the early appearance of a neck which continues to extend throughout the test. As a result the total elongation is directly related to the diameter-to-gage-length ratio. The strain-rate sensitivity of the stress varies during extension, mainly because of microstruc-tural changes. A satisfactory correlation exists between the minimum strain-rate sensitivity and total elongation, as indicated in the equation shown below. Notches cause a considerable reduction in total elongation and their effect is greatest at high values of strain-rate sensitivity. An initial notch depth exists below which there is no appreciable effect on elongation. An equation relating elongation to strain-rate sensitivity and specimen geometry is proposed, THE total percent elongation of a tensile specimen is usually regarded as a measure of superplasticity. However, little attention has been given to the fact that total elongation is also a function of specimen diameter and gage length, even though the importance of geometry has long been recognized in the tensile testing of materials in which elongations are relatively small.* In the present study, the effect on superplas- tic extension of the ratio of specimen diameter to length was investigated and an analysis was made of strain distribution along the gage length. Superplastic alloys are characterized by having a flow stress sensitive to strain rate but relatively insensitive to strain.2"' In an earlier study,5 it was found that the strain-rate sensitivity of several low-alloy steels changed during the test and that the minimum value correlated best with total elongation. In the present study, the variation of strain-rate sensitivity during the straining of a lead-tin alloy was investigated. EXPERIMENTAL PROCEDURE Lead-tin eutectic alloy (32 pct Pb 68 pct Sn), made from high-purity lead and tin, was cast in the form of 1-in. diam rod. The rod was cold-rolled in stages to 0.25 in. diam and then swaged to 0.125 in. diam. Samples were cut from the rod at various stages of the mechanical working process. Tensile test specimens were then made by attaching threaded steel ends to the rods by an epoxy-base thermosetting adhesive which required a setting treatment of 2 days at room temperature. The rods were seated in the steel ends in holes approximately 0.01 in. oversize. The test pieces thus made were of various diameters and gage lengths. These were stored at a temperature of about -70°C (-94°F) until required for testing. The distribution of strain along the gage length of a specimen was determined at various stages of the tensile test. The lead-tin alloy was superplastic at room temperature and direct observations during testing were simple. The gage length was divided by reference marks into five initially equal units. These reference marks were made with ink and were reinforced during the test when the initial marks became faint. Photographs were taken, at intervals, of the deforming specimen and measurements of the elongation in each of the gage units were made on these photographs. Tests were also done on several superplastic low-alloy steels whose properties were described earlier.5 The chemical compositions of these steels are given in Table I. A diagram of the notched tensile specimen used in the steel tests is shown in Fig. 1. The specimens were tested at 900°C (1650°F) in a furnace through which a mixture of He + 2 pct H was continuously circulated.5 RESULTS Strain Distribution. Approximately 20 tests on lead-tin alloy specimens were conducted to determine the strain distribution during the test. An example is shown in Fig. 2 of the strain distribution in the gage

Jan 1, 1969

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By C. S. Finney, John Mitchell

The growing popularity in the United States of the vertical-flue even was emphasized when in 1905 the United States Steel Corp. chose the Koppers oven as the type which best suited their requirements. Heinrich Koppers was born on November 23. 1872. at a small farm in Walbeck near Geldern on the lower Rhine. When young Koppers was eight years old, however the family moved away from the farm to the industrial city of Bochum in the Ruhr. Here Koppers attended public school and subsequently served an apprenticeship to a tinsmith before taking a job as a lathe operator with a local steel company. He had ambitions to be much more than a machinist, however, and used his week-ends and evenings to improve his theoretical background by taking courses at a vocational-training school in Bochum. After winning the highest honor the school could bestow (the silver Staats-medaille), Koppers went on to continue his education at the Rheinisch-Westfalische Hüttenschule in Duisberg. One of his teachers there, Fritz Wüst who later became a professor at the Technische Hochschule at Aachen, recognizing Koppers' unusual abilities, predicted for him a great future. In 1894 Heinrich Koppers joined the firm of Dr. C. Otto and Co. in Dahlhausen, and in 1899 while superintendent of the Mathias Stinnes mine he built his first battery of ovens for Hugo Stinnes, the German industrialist. Two years later he started his own organization, and in 1902 he made Essen his headquarters. It was to Essen that a group of engineers from the United States Steel Corp. went in 1906 with an invitation to Koppers to design and supervise the construction of four batteries of ovens at the Joliet works of the Illinois Steel Co. Each battery was to consist of 70 ovens. Arriving in the United States in 1907, Koppers established a branch of his firm in Joliet, and construction began. The first battery was fired on July 27, 1908. Rugged and simple, these ovens incorporated basic design features which were to make the Koppers oven and its future modifications the choice of a very large segment of the by-product coking industry of America. The 280 ovens at Joliet were 35 ft long, 8 ¾ ft in height, and tapered from 21 to 17 in. The total daily capacity of the four batteries was 2240 tons of coke. The ovens were of the new cross-regenerative type; that is, instead of longitudinal regenerators serving an entire battery, as in the older Koppers ovens, cross regenerators for each separate oven were employed. Fuel gas was supplied from the side of the battery through ducts in the brickwork known as gun flues, which reached to the center of the battery under the vertical heating-flues. Removable, ceramic gas-nozzles fitted at the top of each gun flue helped to insure good control over the distribution of the fuel gas, and uniform heating conditions were also promoted by regulating the air supply to, and the suction in, each heating flue. A different refractory w& used for each battery. One was built of American silica brick, one of American quartzite, and two of imported German quartzite. The installation at Joliet proved to be very successful, and in 1911, 490 additional' Koppers ovens were built for the Illinois Steel Co. at the great new steelworks at Gary, Ind. By 1912 the H. Koppers Co. had established its headquarters in Chicago and was rapidly extending its business to include construction for such iron and steel companies as the Woodward Iron Co. at Woodward, Ma. (80 ovens in 1912); the Tennessee Coal, Iron and Rail- road Co. at Fairfield, Ala. (280 ovens in 1912); the Inland Steel Co. at Indiana Harbor, Ind. (86 ovens during 1913 and 1914) ; and the Republic Iron and Steel Co. at Youngstown, Ohio (68 ovens in 1913). In 1914 a group of men in Pittsburgh bought a major shareholding in the H. Koppers Co., and moved the headquarters of the organization from Chicago to their own city. Under its new management the company was highly successful in obtaining a large share of the contracts for by-product installations built during World War I. In 1917 the remaining German interests in the company were

Jan 1, 1961

By B. S. Butler

A. D. Mutch (Falconbridge Nickel Mines Ltd., Ona-ping, Ontario)—This contribution is prompted by the fact that the writer has recently published an article'!' which has in part the same general conclusions as B. S. Butler's, namely, the form of the standard mineral paragenesis in hypogene deposits and the parallel transition from early high temperature acid to late low temperature alkaline or neutral solutions. Since the writer also recognizes that he is not fully qualified to discuss the formation of ore deposits as a chemical problem, this discussion will be limited to summarizing other observations and will suggest how Butler's Table II might be made more effective. The form of Butler's table is not unlike that widely used by European geologists'" in which the various minerals are related to the types of ore fluids—peg-matitic, pneumatolic and hydrothermal. Thus the decrease in temperature and change in pH of the ore-bearing fluids as recognized by Butler may also be paralleled by perhaps even greater changes in composition, density, and character. W. H. Newhouse's article:" on the sequence of hypo-gene ore mineral deposition is still one of the most complete analyses of the problem. In it he makes four major observations: 1) The order of O, S, As, Sb is the same as their increasing atomic weights and the same as their melting points. 2) The order of the metallic elements is the same as the Schuermann series. 3) The general mineralogical order is paralleled by decreasing heats of formation. 4) The order is generally in decreasing hardness, higher metal content, and higher specific gravity. The order of 0, S, As, and Bi is also the same as their relative abundance. Another point worth mentioning about this series is that As, Sb, Bi, when abundant, often substitute for sulfur in the early pyrite-like minerals, whereas later in the sequence these elements appear to act more like metals. This behavior may be a further indication of the acid character of the early fluids. C. J. Sullivan"' has attempted to show that the sequence of the metallic elements is related to the order of their melting points and has discussed the interrelationship of the different types of bonding of sulfo-phile and oxiphile elements in minerals. Items 3 and 4 might best be summarized by saying that bonding of the minerals in the series appears to be from ionic to covalent to metallic, the early minerals being light in weight, hard, and near-transparent; the intermediate minerals of intermediate weight, semi-transparent, and semi-conducting; and the end minerals heavy, soft, and malleable, opaque and good conductors. A rapid fall in temperature has been assumed to be the cause of ore deposition in many deposits. Perhaps this in turn is the effect of a rapid release of energy in the form of pressure release and change of volume, the first minerals to form being those with the highest heats of formation which absorb the released energy the most rapidly. Butler's Table II could probably be streamlined and made more effective if the listed compounds were assembled as mineralogical groups as in Dana. Thus the sulfides, arsenides, antimonides, bismuthides, and sulfa salts could be arranged in AX,, AX, A2X2, etc. groups. Since these are continuous substitution series, in which the fields of stability and the heats of formation of the various individual minerals can be fairly regarded as similar, this should be accomplished with no loss of clarity. The occurrence of the individual minerals and the precise sequence of the mineral deposition in any one deposit is probably more dependent on the concentration and relative abundance of the component elements. The assembling of geological data in tabular form such as Butler's Table II will continue to be a very effective method of studying geological phenomena. The importance of this particular problem has been pointed out by C. F. Park,% who concludes that understanding of mechanisms of the standard paragenesis and interrelated problems of mineral zoning in space and time is one of the major keys to classification of ore deposits.

Jan 1, 1959

By Don M. Jackson, Robert W. Howard

Techniques for the epilaxial growth of single -crystal silicon carbide films on silicon were developed. The vapor-phase decomposition and bydrogen reduction of silicon tetrachloride (SiC14) and Propane (C3H8) resulted in clear films of silicon carbide, lip to seveval microns in thickness. The growth took place in a horizontal . silicon epilaxial reactor at 1100°C (pyrometer) at a rate of- 3000Å per minute. Electron diffraction and X-ray diffraction studies demonstrated that the films were single-cyrstal, ß -phase, or cubic silicon carbide. SiO2 film were used to mask areas of the silicon sur-lace in order that the silicon carbide might be grown in controlled geometries. Both n- and p-type films were grown on p-type silicon waters.. Heavily doped silicon films of the same conductivity type as the silicon carbide films were deposited over the silicon carbide in order to affect better probe contact to the structures. when n-type silicon carbide mesas were grown on p-type silicon substrates the de vollage-current relationships between films and substrates were that of junction diodes. These diodes showed a sensitivity to while light ill that the incident light increased forward- and reverse-satro,ation currents, P-type silicon carbide mesas grown on p-type silicon were ohmic rather than rectifying in their voltage -current relationship. No conclusions could he reached concerning heterojunc-tiou rectification in the structure. SILICON carbide is a semiconductor with many interesting properties. It decomposes at temperatures above 2200°C.1 It occurs in two general crys-tallographic forms—hexagonal (a Sic) and cubic (ß Sic)—with the cubic form having a forbidden-gap energy of 2.32 ev and the hexagonal form (specifically the 6H polytype) a gap energy of 2.86 ev.3 It behaves as an extrinsic semiconductor at temperatures approaching 5003C. It has been shown to have a high resistance to radiation damage4 and p-n junctions formed in Sic have been shown to radiate visible light under forward- or reverse-bias conditions. Epitaxial silicon carbide on silicon carbide has been successfully grown through the use of a variety of techniques, such as gaseous cracking of SiCL4 and CC4, nearly all of which require a deposition temperature above 1500°C.6 This paper will cover very recent work on the gas-phase deposition of highly ordered films of silicon carbide on high-quality silicon single-crystal substrates. The films have been shown to ex- hibit junction-rectification properties when geometrically isolated regions are electrically biased with reference to the silicon substrate. There will be no discussion of the mechanism of heterojunction rectification, but the methods of film fabrication, geometry control, and structural evaluations will be covered in detail. Electron diffraction, X-ray diffraction, and diode electrical properties were used to characterize the films and the junctions. GAS-PHASE DEPOSITION OF Sic The techniques for the deposition of silicon carbide films were a logical outgrowth of the standard silicon epitaxial process. The major premise followed was that, for any film to nucleate in an ordered fashion where there is considerable mismatch in lattice parameters (in this case 22 pct), an extremely clean, damage-free substrate surface must be presented to the gas stream. Thus a standard gas-phase HCl etching step was used to prepare the substrates for growth. A minimum of 5 µ of substrate-surface material was removed prior to the deposition of Sic overgrowth films. The techniques used for growing silicon carbide films were those of growing silicon alone, with the added injection of a hydrocarbon gas into the hydrogen and silicon tetrachloride gas stream. The hydrocarbon gases used thus far have been research-grade (99.99 pct) methane (CH4) and propane (C3H8). Propane ultimately gave the best results. The gas flows were controlled through a panel shown schematically in Fig. 1. A hydrogen main stream of 30 liters per min passed through the horizontal quartz-tube epitaxial reactor, while SiC14, C3H8, HC1, and doping gases were injected as side streams. The

Jan 1, 1965

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.''' A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.' In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.''7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, 'which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By J. C. Fisher

Martensite transformations in steels and other alloys are characterized in part by the absence of composition changes during the growth of a new phase. Transformation occurs rapidly, and there is insufficient time for long range diffusion or partition of alloying elements to take place; martensite reactions in alloys thus are similar to phase transformations in single component systems. A fundamental understanding of martensite transformations in steels is impossible without knowledge of the free energy change upon transforming austenite (face centered cubic iron containing alloying elements) to ferrite (body centered cubic iron containing alloying elements) of the same chemical composition. The present paper assembles the best information available concerning the influence of temperature and composition on this free energy change. Most of the material has been taken from the work of Johansson,' Mehl and Wells,2 Zener3,4 and Smith;5 and indirectly, through these authors, from the work of Austin.6 In agreement with the generally accepted viewpoint, martensite is assumed to be an ordered solution of carbon in ferrite of the same composition as the parent austenite; only at high temperatures and low carbon concentrations is the carbon in ferrite distributed at random. The properties of the disordered solution are estimated by extrapolating the known properties of iron-carbon solid solutions into the range of supersaturation, and the free energy change associated with ordering is estimated from the theory developed by Zener. By incorporating Smith's recent thermodynamic measurements and Zener's theory of ordering, the present analysis modifies previous estimates of the free energy change associ- ated with martensite transformations. Consider a two component system consisting of a solvent A and a solute B. Let Na and Nb represent mol fractions of A and B respectively, let aa = raNa and ab = YbNb represent activities, and let superscripts 1 and 2 refer to phases 1 and 2. The partial molal free energies of A and B in phases 1 and 2 can be summarized as follows: free energy standard state Fa' - Fao1 = RT In an1 pure A' Fa2 - Fa2 = RT In aa2 pure A2 Fb1 - Fbo = RT In ab1 pure B Fs2 - FB2 = RT In aB2 pure B. The free energy of a gram atom of phase 1 is* AF1 = Na'Fa1 + Nb'Fb1 and that of phase 2 is AF2 = NA2FA2 + NB2Fb2. A martensite transformation from phase 1 to phase 2 requires Na1 = Na2 = Na and NB1 = NB2 = Nb, and the free energy change per gram atom accompanying transformation is AFi-2 = NA(Fa2 - Fa1) + Nb(Fb2 - Fb1) = NA[RT In (aA2/aA1) + AFa1?2] + Nb RT In (aB2/aB1) = Na[RT In (ra2/ra1) + AFa1?2] + Nb RT In (TaVTB1). [1] where yn2, yn1, yB2, yB1 are activity coefficients, and where Ma'+* is the free energy change upon transforming a gram atom of pure A from phase 1 to phase 2 at the temperature in question. For martensite transformations in plain carbon steels, A = iron (Fe), B = carbon (C), 1 = austenite (7). 2 = ferrite (a), and Eq 1 is AFr ?a= NFe[RT In (rf.a/rfer) + AFF.r?a] + TVc RT In (eca/rc1)- L2] Nothing is known concerning the values of yFea and yca for carbon concen- , trations in excess of 0.025 pct. However, the approximation rf.7 = 7f." = 1 cannot be appreciably in error for small carbon concentrations, and Eq 2 reduces to Afr-a = NfeFfer?a1 + NC RT In (rca/rcr)- [3] Johanssonl and Zenera have calculated MFfr?a from the specific heat measurements compiled by Austin.6* Their calculated values agree closely, and are summarized in Table 1. The activity coefficients relative to graphite for carbon dissolved in iron vary with temperature according to the relationships d In rcr/d(1/T) = AHcr-R dlnyca/d(l/T) = AHCa/R where AHc? and AHca are the heats of solution of graphite in y and a iron. Assuming the values of AH to be independent of carbon concentration and temperature, In rCr = AHcr/RT + I1 In rca = AHCa/RT + 12

Jan 1, 1950

T.B.King (Depaytment of Metallurgy, Massachusetts Institute of Technology)— A valuable contribution of the authors is in the factual information which they have been able to gather; this type of information is quite difficult to obtain. In many respects, however, it would have been better if they had not subsequently embarked on a discussion of the chemistry of the converter process. It seems inconceivable that the authors do not refer to the papers of Schuhmann and his associates14 which have set the thermodynamic foundation for the whole copper smelting operation. In addition, a very useful review on the physical chemistry of copper smelting by Ruddle 5 appeared as long ago as 1953. An examination of this literature would have convinced the authors that there is no cause to be surprised at a correlation between the magnetic content and the silica content of converter slags, though they rightly point out that one should distinguish between the total magnetite content of the slag and the amount of magnetite which may be considered to be in solution. It is not true that the lowest melting converter slag is that corresponding to the eutectic between ferrous oxide and silica. The simplest slag system which can be considered is a three-component system, since both ferric and ferrous iron are present. As Schuhmann, Powell, and Michal have shown, there are lower melting compositions than this eutectic in the ternary system. The most unfortunate impression given by this paper is that the driving force for chemical reaction is determined by the heat of reaction: of course the entropy change must be taken into account. It would have been more correct to list, in Table VI, values for free energies of formation. Nor can it be said that the data in Table VI represent the "best available data." They do not corregtond with any of the recent, acknowledged sources. F. E. Lathe and L. Hodnett(author's reply)— We are pleased that Dr. King finds the factual information in our uawer of some interest. Dr. King suggests that it would have been better if our analysis and discussion of the data had been omitted, largely because our list of references is so. incomplete. If he will carefully read our introduction, he will see that the questionnaire was sent out in the hope of obtaining data which would throw light on certain questions relating to the use of converter refractories. We did not attempt (nor would the AIME have published!) a complete review of the literature on copper converting, as Dr. King has apparently assumed, nor indeed a complete analysis of the data submitted, but tried only to find a sound basis for the choice of refractories, taking into consideration common variations in converter practice. We hope our paper indicates that, by raising the silica content of the converter slag and operating at a higher temperature, the normal circulating load of magnetite can be greatly reduced, and the whole reverberatory-converter operation improved to a major degree, with resultant important savings. Under such operating conditions, chrome-magnesite brick may be expected to stand up better than those of straight magnesite. Regardless of the choice as between these brick types, however, we find the cost of converter refractories to be so low in comparison with other converter costs as to justify operation under the more severe conditions suggested. Valuable as are the papers by Schuhmann and associates and the book by Ruddle, we make no apology for omitting reference to them, nor for using heats of reaction without mention of entropy changes or free energies of formation. Our primary object was to interest the practicing copper metallurgist, with whose language we may claim to be fairly familiar; we think it would have been unwise to include the highly theoretical phases of the subject which Dr. King suggests. The interest shown in our preliminary paper presented at the New York meeting in 1956, and the trends in practice whtat we have observed since that time, suggest that we did not wholly miss the target. In conclusion, we sincerely hope that Professors King and Schuhmann will independently review the data obtained in our questionnaire and submit a paper giving their own recommendations as to the choice of refractories and the particular converter operating conditions which will result in the lowest overall cost of copper smelting and converting.

Jan 1, 1960

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.' Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts' Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg's method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By Wallace W. Wilson

This DaoerAA calls to attention for the first time, to the writer's knowledge, a purported recovery of oil by substantially horizontal gas cycling that is considerably in excess of 50 per cent of the oil originally in place. The average angle of dip along the path of travel of the gas is less than one degree of arc. The best recovery by gas cycling previously brought to the writer's attention1 occurred in the case of the Mile Six Field in Peru, where about 68 per cent of the original oil in place has so far been recovered. In this case, however. the recovery was greatly aided 1)y the high dip angle of about 17.5". An approximate estimate of recovery was made by the method developed by the writer' for the case of the Cook Ranch Field, using an average relative permeability ratio function dictated by past experience with a number of good quality sandstones. A result of about 40 per cent recovery of the original oil in place wa* obtained after the 8.5 pore volumes of cumulative gas cycling undergone by the Cook Ranch Field. Tile writer desires to emphasize what appears to him as the sound engineering practiced at Cook Ranch, and also the care attending the taking of data and the high quality of the calculations made. It is impossible to take issue on factual grounds with any of the conclusions drawn in the paper. It is, however, desired to point out the difficulty of explaining the unexpectedly favorable oil recovery on ordinary theoretical grounds. It would be of interest to know whether relative permeability ratios have been measured on the Cook sand. The operator is inclined to attribute some of the excess benefit to settling of the oil across the bedding planes into the lower part of the sand. It is difficult for the writer to appreciate the importance of such an effect, inasmuch as the concomitant opening of excessive vacated pore space in the upper part of the sand would he expected to cause excessive bypassing of the gas. REFERENCE 1. Welge. H. J.: "A Simplified Method for Computing Oil Recovery by (Gas or Water Drive." Trans. AIME, (1952), 195, 91. AUTHOR'S REPLY TO MR. WELGE Welge has poined out clearly the difficulty of applying material-balance procedures in calculating the Performance of low-pressure, dispersed gas injection operations. There can be no argument that even with the most favorable assumptions of K,/K,, and with cumulative gas cycling in excess of normal expectations, the calculated oil recovery will be considerably less than the 72.5 per cent recovery realized from this project to Jan. 1, 1951. There probably are at least two reasons for the unusually high recovery from this reservoir, the effects of which would be difficult or impossible to calculate by known methods: 1. The operator did not use the same injection wells for the entire operation, and exercised considerable control over producing GOR by changing the locations of injection wells whenever well performance indicated excessive bypassing. Fifty-six wells were used for injection, not over 29 of which were in use simultaneously. This procedure resulted in frequent shifting of the fluid movement patterns in the reservoir and undoubtedly increased the ultimate recovery. The writer knows of no satisfactory procedure for calculating the effect of this practice. 2. Vertical movement of oil across the bedding planes of the reservoir rock hy gravity drainage tended to maintain a relatively high oil saturation, and hence a favorable K,/K, ratio, in the lower sections of the reservoir. As pointed out by Welge, this condition has aggravated the tendency for high producing GOR, but at the same time it has resulted in increased oil recovery. As may be seen from the performance charts for the various battery areas, operating (GOR'S have been quite high for the last several years of reported history.

Jan 1, 1952