Search Documents

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By G. S. Hume

During the war years the drilling activity in Canada has been steadily increasing and still further increase is expected in 1945. The production of oil, which in the past has come largely from the Turner Valley field in Alberta, shows a decline since 1942, the peak year. New discoveries made in 1944, however, give promise of replacing the decrease from Turner Valley where the crude-oil production in 1944 was nearly 1,800,000 bbl. less than in 1942, but with an increase of 145,000 bbl. in natural gasoline, a product of great value to the war effort. A very considerable part of the decline in Alberta has been offset by new production of more than a million barrels in 1944 from the Norman Wells field, in the Mackenzie River area of the Northwest Territories. It should not be forgotten, however, that this is largely due to the Canol development, a war project, the future of which is dependent on many factors not connected with an ordinary commercial operation. The year 1944 has been the best in new discoveries in Alberta for all time. The discovery of a new deep field at Jumping-pound, 20 miles west of Calgary, with the hopc of a type of product similar to that of Turner Valley is the culmination of many years of effort to interpret the subsurface structures in relation to the complicated surface foothills faulting and folding. In this case the subsurface structure on the Paleozoic limestone was inferred from geological investigations but precisely defined by seismograph. In addition to Jumpingpound the discovery of oil of 34.5 gravity at a depth of less than 5000 ft, in the Devonian of the Plains at Princess, 125 miles east of Calgary, is of great significance since this is the first substantial production from the Devonian in Alberta, although previously some oil had been obtained at two places from the Devonian in the foothills. The effect of this discovery is already apparent in the number of wells now drilling to the Devonian in the southern Plains. In southern Alberta a new producing area has been found in a Lower Cretaceous sand at Barnwell, a few miles west of Taber. Also, at Conrad, 20 miles southeast of Taber, an important new discovery has been made at a depth of about 3000 ft. in a sand in Jurassic shales, in a strali-graphic trap on the northeast flank of the Sweetgrass arch. In northeast Central Alberta an important extension has been found in the Lloydminster area, where only a few wells have so far been drilled. A new well 3 1/2 miles south of the previous producers found a coarser sand at the productive horizon and as a result will have an increased daily yield. At Blackfoot, 9 miles west of Lloydrninster, a new producing area in the Lower Cretaceous may have been discovered at a depth of 2004 ft. At the end of 1944 the well was being tested. Forty-four unsuccessful wildcat wells were drilled in Alberta in 1944. The decline of Turner Valley, the major producing field, was anticipated at the beginning of the war and in an effort to offset this and encourage new development the Dominion Government put into force tax concessions and other measures that,

Jan 1, 1945

By H. B. Heller, T. J. LaChapelle

Phosphorus nitride has been used as a diffusant for introducing phosphorus into silicon under various conditions. It has a temperature -dependent rate of decomposition beginning in the 500°C range, increasing very rapidly above 1000 C, producing gas -eous phosphorus and nitrogen. Best control was obtained with a two-temperature arrangement, with silicon at the proper higher diffusion temperature. It is an easier compound to use than the usual P2O5 because it is nonhygroscopic and yields temperature-controlled surface concentrations together with excellent final surfaces. Surface doping nearly as high as that produced by phosphorus pentoxide has been observed for sources at 850" to 900°C. Reproducible high sheet resistances were obtained by using slow flow rates (1 linear in. per min) and staggered-baffle gas mixing with the nitride at 550°C. Both inert gas (argon, nitrogen) and oxidizing ambients have been examined. Oxygen reacts to produce anhydrous P2O5, consuming the source at a rapid rate. Nitrogen, except for short diffusion times, suppressed the dissociation reaction and sometimes produced inferior surfaces. Argon appears to be a more useful ambient. PHOSPHORUS is a common impurity atom which may be introduced into a semiconductor lattice to create a p-n junction or an nn contact region. Various investigators1-4 have described techniques which can be used with either elemental phosphorus or certain of its compounds. This paper discusses a newly available compound of phosphorus, phos- some processes silicon wafers are precoated with a phosphate glass which acts as the doping source. Although a nonoxidizing form like elemental phosphorus or a phosphine can be used, most diffusion methods usually involve the use of phosphorus pentoxide. Because of the rapid volatility of this compound, a two-step process is often used, combining a gaseous deposition to introduce a predetermined quantity of phosphorus into the silicon with a later redistribution to obtain the desired distribution and surface concentration. Such a process usually involves predepositing phosphorus at surface concentrations greater than 1020 cm-'. At such doping levels the phosphorus-diffusion coefficient appears to be strongly concentration-dependent.596 Distribution profiles5'9 for these high concentrations of phosphorus do not follow Fick's laws, having extended subsurface regions which appear electrically to be nearly uniformly doped with ionized impurity atoms. Radioactive-tracer experiments also show near-surface anomalies in the distribution profile. Additionally, it has been shown1' that the introduction of very high surface concentrations of impurity atoms into silicon (a step necessitated by the subsequent lowering of concentration during the redistribution) creates dislocations, even in material having no dislocations originally. For device fabrication the use of oxide masking introduces certain difficulties and limitations.7'8 The standard practice of using phosphorus pentoxide as an impurity source adds other problems to these because of the speed and ease with which this compound reacts with moisture present in any gas in contact with it. In fact, P2O5 is one of the fastest and most effective drying agents for gases. Because it is such an excellent desiccant, completely anhydrous phosphorus pentoxide is difficult to obtain and is even more difficult to keep dry. Adequately dry gloved boxes must be used for storage and transfer of the chemical. The presence of even traces of moisture will cause formation of phosphoric acids which, during the high-temperature diffusion, results in polyphosphoric acids of variable composition. Such reaction by-products end up as gradually accumulating viscous fluids in the cooler parts of the diffusion furnace. The calculation of the final solute distribution for

Jan 1, 1964

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By C. Perez-Rosales

A simplified method for evaluating specific surface of porous media is described. The theory takes as its point of departure a previous statistical method. Due to its simplicity, it is considered that the proposed method has certain advantages over methods currently used. By making some simplifications, the procedure for estimating specific surface is reduced to superposing, on an enlarged reproduction of a section of the sample to be analyzed, an evenly spaced grid and counting the number of intersections of the grid lines with the perimeter of pores. An indirect test of the theory is presented and the advantages of the method are discussed. INTRODUCTION The specific surface of a porous medium, defined as the surface area of the pores per unit bulk volume, is an important parameter with regard to flow of fluids through porous materials. In particular, it has long been recognized that specific surface is closely related to permeability. Since the internal surface of any porous material is extremely complex, the measurement of specific surface can only be accomplished by indirect means. It is considered that the best method' in current use for determining specific surface is the statistical method of Chalkley, Cornfield and Parka who originally applied it for estimating volume-surface ratios of morphologic components, such as cells or nuclei. This method will be outlined later. A method which has been used extensively in determining specific surface is based on the adsorption of a vapor by the internal surface of porous media. However, this method does not yield the surface pertinent to fluid flow, since it includes the tiny molecular interstices which do not influence the permeability of the porous material.' This method has been employed by Brooks and Purcell measure internal surface area of sedimentary rocks. The Kozeny equation, which relates the specific surface to the permeability of a porous medium, has found wide use in determination of specific surface. However, the KOzeny equation is not strictly correct. Large discrepancies have been found between theory and experiments.' Consequently. the specific surface estimated by this method is subject to serious uncertainties. Finally, there are other methods for specific surface measurements which are based upon a variety of physical and chemical properties: the heat conduction by a gas, ionic adsorption phenomena and direct chemical reactions of the surface with other substances. This paper describes a simplified statistical method for determining specific surface of porous materials. It is considered that, due to its simplicity, it has certain advantages over the methods presently used. For its validity, it is required that the porous structure of the material under study be of a spatially random nature. This is not a serious limitation since the naturally occurring porous media have this characteristic. THEORY The method proposed in this paper takes as its point of departure the interesting result obtained by Chalkley et al The method shows that if a line of length r is dropped repeatedly at random over a section of a porous medium, and counts are made of the number of times the two end points fall within pore areas (denoted by h for "hits") and the number of times the line intersects the perimeter of pores (denoted by c for "cuts"), then in a very large number of throws where S is the internal surface of the sample (surface of pores) and V, the volume of the pores (Fig. 1). Since the specific surface S, and the porosity 4 are given, respectively, by S. = Sl V, and 4 = V,l V,, where V, is the total volume of the sample, it follows from Eq. 1

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-'100' crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By W. A. Wood, H. L. Wain, R. I. Garrod

The mechanical behavior of recrystallized chromil~m of high purity has been studied, principally in torsion and to a lesser extent in tension, at temperatures between —196oand 350oC. Depending upon the conditions of test, the material may show brittle or ductile behavior or an intermediate or subduc-tile state having some of the characteristics of each. This latter state existed at temperatures between approximately ±50°C and was characterized by a) extensive creep at stresses well below the normal fracture stress, b) nonelastic loading/unloading effects during creep, c) strain softening under cyclic loading, and d) final failure of a brittle type. Suggestions are made on the dislocation processes and interactions which give rise to subductile behavior The ductile-brittle transition in bee metals has been studied mainly by tension and bend tests. These methods, however, favor crack propagation which may follow too closely on initiation for detailed study of the transition itself. For work of this nature, therefore, other modes of deformation less favorable to crack propagation may be preferable. This paper describes a study of the ductile-brittle transition in chromium which is based mainly on torsional testing although a few subsidiary experiments were made in tension. It appears to reveal at the transition an intermediate state that cannot properly be described as either brittle or ductile. Torsional tests on chromium have been made by other workers1 but not, as here, primarily for study of this intermediate state. EXPERIMENTAL The chromium, in the form of swaged rod, was prepared by techniques already described.' The particular material used was one in which the main impurities were 0.03 wt pet 0 and 0.006 wt pet N and one in which transition from ductile to brittle states in torsion conveniently fell at about room temperature. For torsion, test specimens were from 5/16-in.-diam rod to provide test portions 1-1/4 in. long by 7/32 in. diam, a twist of 1 deg thereby corresponding throughout this paper to 0.0015 surface shear. The specimens before test were annealed for 2 hr at 1200°C in vacuo, which left them with a re-crystallized grain size of about 0.01 mm, and then electropolished. They were tested under dead-weight loading in an apparatus in which they could be surrounded by a furnace or cooling chamber, tests in practice being made at various temperatures between -196" and +350°C. For tension tests, cylindrical specimens were prepared in a similar manner and tested at room temperature under dead-weight loading. RESULTS (TORSION) Subductile State. The state described above as intermediate between brittle and ductile may be perhaps best defined by reference to torque/twist curves at various temperatures. These are grouped in Fig. 1. Below about -50°C the material was brittle, in the sense that it exhibited little plastic deformation under stress and fractured by cleavage along planes of maximum resolved tension, which in torsion produces the well-known helical type of fracture. The deformation is typified by the curves for -196" and -150°C in Fig. 1; it shows a slight but progressive deviation from linearity above a certain torque, here about 50 lb-in., until fracture occurs at about 95 lb-in. A feature to which it is desired specially to call attention is that under none of the loads did the specimens show significant creep.

Jan 1, 1964

By S. Leber

Pole figures and pole distributions were used for the quantitative detevinination of the preferred orientations in swaged tungsten rods and the effect of subsequent wire drawing on the texture. In the swaged rod, the preferred orientation could best be described as a pseudo (111-112) [110] cylindrical texture. A secondary component was assigned the indices (110) [001]. Further reduction by swaging retained these cylindrical textures. Wire drawing caused lattice rotations about the wire axis, converting the cylindrical texture into a normal fiber texture. The conversion was initiated and proceeded lnost rapidly in the center of the wire. The (110) /001] component was converted into a (110) fiber texture by wire drawing. The effective rotations were about axes contained in the lransverse plane. The preferred orientation associated with tungsten wire usually has been assumed to consist of a (110) fiber texture. This implies rotational randomness around the wire axis. Leber1 has shown that rotation about the wire axis may be restricted resulting in a preferred orientation designated as a cylindrical texture. Specific crystal planes tended to remain aligned parallel to the wire surface. This texture seemed to be the result of the swaging operation used in the intermediate stages of fabrication. Bhandary and cullity2 detected similar textures in swaged iron wires. Peck and Thomas3 suggested that the preferential alignment of crystal planes parallel to the wire surface was the result of tangential flow, characteristic of swaging. Wire drawing, following swaging, twisted the crystals about axes parallel to the wire axis, converting the cylindrical texture into a normal fiber texture.4 In this investigation, quantitative techniques were used to more accurately characterize the cylindrical texture and to study its conversion into a normal fiber texture. PROCEDURE The material investigated was lamp-quality tungsten. Three ingots were rod-rolled and swaged to 112 mils diameter, and were then drawn to 10-mil wire. Samples were obtained after each drawing pass. (110) and (200) pole figures were obtained from samples prepared as shown in Fig. 1. To form the sample shown in Fig. l(a), l-in. lengths of wire were glued side by side to form a l-in. square. The composite was ground and electropolished to form a diametral reference surface. For certain specific tests, samples were prepared as shown in Fig. l(b). This composite was made from 10-mil-thick strips prepared by grinding on parallel longitudinal planes. The polished reference surface in this case was, in essence, the wire surface. The two forms of samples [~igs. l(a) and l(b)] were related by a 90-deg rotation around the wire axis. Because of ease in preparation, most data was obtained from the diametral samples. The X-ray data were obtained using a Siemen's pole-figure goniometer. These data were not corrected for absorption or defocusing effects, since only the angular locations of the intensity maxima were of interest. Regions of the pole figure more than 80 deg from the center were not investigated. Partial monochromatization was achieved by the use of unfiltered copper radiation and a krypton-filled proportional counter. No evidence of spurious white radiation effects5 could be detected. Therefore, more elaborate X-ray techniques were not required. Intensity levels were chosen to show all pertinent details of the orientation distributions. The reference plane for the pole figures was the diametral section. The orthogonal reference directions, shown in Fig. 1, were the wire axis, the radial axis per-

Jan 1, 1965

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

By Guy Borden, Michael J. Rzasa

Laboratory data on bubble point pressures and reservoir volume factors have been correlated as functions of solution gas-oil ratio, calculated gas gravity of the pentanes-and-lighter fraction of the entire fluid, differential residual oil gravity, and reservoir temperatures. INTRODUCTION Several correlations of crude oil properties have appeared in the literature. D. L. Katz4 in 1942 presented five methods of predicting oil shrinkage. these being of decreasing accuracy for decreasing amounts of information available. M. B. Standing- in 1947 published three correlations of laboratory flash vaporization data of California crudes. From values of GOR (gas-oil ratio), gas gravity, liquid gravity, and temperature, his correlations will predict bubble point pressure, formation volumes of bubble point liquids, and two-phase formation volumes. Curtis and Brinkley2 in 1949 presented several correlations. From the gas-oil ratio, an approximation of reservoir volume factor and barrels of condensate recoverable per barrel of reservoir space may be obtained; along with liquid gravity and reservoir temperature, the GOR will allow prediction of bubble point pressure. These last cor- relations seem to be more qualitative than quantitative. Generally, laboratory bottom hole sample tests furnish information on solution gas-oil ratios, residual oil gravities. bubble point pressures, viscosities of oils, liquid shrinkages, and occasionally gas gravities. Each of these data has its own applications and use in reservoir engineering calculations. The particular uses of correlated bottom hole sample data are found in (1 Providing a basis for obtaining estimates of formation crude properties in fields where bottom hole sampling is impractical or impossible. (2) Greatly reducing the time in obtaining the desired information. (3) Determining the applicability of the results from various bottom hole samples to particular field problems. (4) Avoiding, in many cases, the uncertainties of sampling by replacing it with an element over which greater control can be exercised. (5) Permitting use of preliminary field data in application of production procedures before a bottom hole sample can be obtained and analyzed in the laboratory. (6) Serving as a check on data which may appear out of line. (7) Estimating for a particular type crude the appropriate equilibrium constants by working backward from the bubble point pressure. (8) Estimating original or other past history properties of reservoirs that were not sampled in the past. PROCEDURE Application of the published correlations4,6 to Stanolind laboratory data indicated that the general scheme presented by Standing" could give dedrable results if changes were made in parameter positions and scales. The correlation curves were drawn with all the variables having consistent gradations except the temperature increments which were drawn in to best fit the data. The variables from available Stanolind laboratory data are defined below: (1) Gas-oil Ratio: Gas is liberated at reservoir temperature by differential vaporization (or rather by a series of flashes, approaching differential vaporization) and measured at atmospheric pressure and temperature, at which the compressibility factor is assumed to be unity. The oil is the residual liquid remaining after the pressure has been reduced to atmospheric. For the gas-oil ratio both volumes are corrected to standard conditions of 14.7 psia and 60°F. (2) Gas Gravity: It was decided to arbitrarily divide the hydrocarbons of the entire bottom hole sample into pentanes-and-lighter and hex-anes-and-heavier, and use a calculated gas gravity of the pentanes-and-lighter for a correlating variable. (Sample calculation is shown in Table 111.) (3) Liquid Gravity: This is the API gravity of the residual liquid from the differential vaporization. The gravity is measured at room temperature and corrected to 60°F.

Jan 1, 1950

By A. G. Metcalfe

Observations at temperature are used to investigate the phase changes in alloys containing more than 50 pct Co and above 1000°C. The nonsuppressible transformations in cobalt above 1120°C and in the intermetallic compound Co2Cr3 are studied. The liquidus and solidus surfaces are determined. Insufficient data is obtained to complete the constitution diagram. A REVIEW of some of the earlier work on cobalt' and on the binary systems with chromium2-4 and with molybdenum,5 showed that one likely source of differences might be attributed to the presence of phases at high temperatures which could not be retained by quenching. Consequently, the decision was made that only methods of examination at temperature should be used in this work. The correctness of this decision was confirmed during the course of the work by the investigation of the martensitic nature of the transformation in cobalt- and by the decomposition of the high temperature form of the phase Co2Cr3 on quenching.' The use of high temperature methods, including dilatometry and thermal etching led to the postula-tion of the existence of a high temperature form of cobalt with a probable hexagonal close-packed structure, transforming from cubic cobalt over a range of temperature from 1119° to 1145°C.8 One of the important pieces of evidence for this transformation was that it was observed in alloys with chromium and molybdenum which were nonmagnetic at this temperature so that confusion with magnetostriction effects was impossible. These results were not reported in this earlier paper, so that the data given here supply further evidence for the existence of a second allotropic transformation in cobalt. High temperature observations are necessarily much slower in producing results than the examination of quenched specimens at room temperature by conventional means such as X-ray diffraction or microexamination. The investigation has only covered a limited part of the field, as a result, extending from the liquidus down to about 1050°C and from the cobalt corner up to 50 pct alloying elements. The differences between the various reported diagrams for the constitution of the Co-Mo and Co-Cr systems have already been mentioned. The best available diagram in the first system is due to Sykes and Graff' which is shown in Fig. 1. Fig. 2 shows the latest Co-Cr diagram due to Elsea, Westerman, and Manning.' A comparison reveals that these are incompatible because of the disagreement with regard to the number of allotropes of cobalt. Elsea, Westerman and Manning took their liquidus and solidus curves from Wever and Haschimoto.2 The temperature horizontal in the two-phase field beneath the eutectic was placed 35" to 39°C higher than in earlier work2,4 with a new interpretation of the nature of this transformation. This interpretation also required a peritectic horizontal at about 1470°C, which has been confirmed here for an alloy with 53 pct Cr. No investigation had been made of the ternary system until after this work had been terminated, when a section at 1200°C was published." In this work a ternary compound was found by the X-ray diffraction examination of quenched alloys. This compound contained less than 50 pct Co, and was thus outside the field investigated here. However, some reactions were found dilatometrically which could not be fitted on the diagram and are now believed

Jan 1, 1954

By Granville S. Borden

MANY complaints have been filed by mine prospectors, explorers and producers about inequities in mining taxation. They have insisted upon improvement, and in the past 35 years there has been some progress. Many of the best taxation provisions made to date are those contained in the Revenue Act of 1951. Mining economics presents special problems, a fact even recognized by many textbooks. Certain provisions have been made to take care of mining taxation rights, but these have been made by Congressional act and do not represent basic, constitutional, guarantees. Despite special provision, in the form of depletion allowances, there remain injustices. The industry faces the problem of gaining adequate income tax allowances for exploration and development expenditures, operating losses, and bonus and subsidy payments. Problems in mine taxation arose soon after the adoption of the 16th Amendment. This amendment gave Congress the power to impose income taxes. Supreme Court decisions against a number of mining companies held that Congress, under its power to tax income, could tax net operating revenue before depletion allowance was deducted. The court also ruled that the right to deduct depletion is a matter of Congressional permission. There is no statute provision permitting mining stockholders to recover their investment out of dividends while the mine is being operated. The Supreme Court did not recognize that part of mining proceeds are actually amortization of the cost of mineral rights. Both these omissions stem from failure to recognize that by its very nature mining consumes its mineral rights and therefore that a part of gross proceeds are not income but recovery of capital. Suppose a Congress unfriendly to mining interests repeals the provisions that allow deductions for depletion. Under such a situation assume that a corporation buys a mineral deposit for $300,000. They mine the deposit and earn an operating profit of $500,000. At the current rates they would pay a Federal Income tax of in excess of $250,000. This venture results in a loss of $50,000 as shown in the table below. For the example given the absence of depletion provisions in income tax law would turn ore into waste rock, because the word "ore" connotes commercially mineable rock. [ ] In retrospect the conclusion is clear: If the Supreme Court had recognized that a part of mining proceeds represent in reality sales proceeds of mineral rights, then profits derived from such sales would have been taxed at the favorable long-term capital rates, instead of being taxed at the high normal, surtax and excess profits rates. It is a question whether percentage depletion allowances offset this tax situation. History The history of depletion allowances has been one of general improvement. The original act did not include depletion, but an allowance at the rate of 5 pct of gross proceeds was provided in 1913. The Acts of 1916 and 1917 allowed depletion upon cost of property, and in 1918 the law was further changed to permit depletion upon cost, or market value as of date of discovery. In 1932 metal, coal and sulphur properties were permitted to elect depletion in percentages of gross income, limited to 50 pct of net income, in lieu of cost depletion. Shortly thereafter the rule was changed and percentage depletion is now allowable in any case where it is higher than cost depletion. Since 1942 percentage depletion allowances have been extended to cover many nonmetals, and in 1951 the rate for coal mines was increased from 5 to 10 pct of gross income. It is interesting to note that these allowances have been retained, and even

Jan 1, 1952

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen' to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By F. W. Bloecher

DETERMINATION of the surface area of finely divided minerals is of interest to mineral engineers engaged in flotation, comminution, and de-watering studies. In the industrial minerals field, many materials are classified as to fineness according to their specific surface (surface area per unit weight). A method of surface area determination has been tested and used in the Richards Mineral Engineering Laboratories at M.I.T. It involves low temperature krypton adsorption measurements using the technique described by Beebe.' During the past fifteen years a number of new surface measurement techniques have been developed. Those that are broadly applicable to materials dealt with by mineral engineers include the permeability method in which a gas or liquid is passed through the sample, and the low temperature gas adsorption methods first described by Brunauer, Emmett, and Teller."" Efforts to make surface determinations from size distribution curves have long been attempted"."." but because of the uncertainty of sub-sieve size distribution and inaccuracies in screen analyses, the method is at best only a rough approximation. The most widely used gas adsorption method utilizes nitrogen gas." Nitrogen adsorption, however, is not particularly suited as a tool for most mineral engineers because the method is not applicable for surface determinations on coarse materials, that is, materials coarser than approximately 150 to 200-mesh. Other gases have been used in mineral engineering studies, particularly ethane."' lo The use of ethane gas, however, involves .a technique that is too sensitive for most mineral engineering work. The permeability method of surface area determination has the disadvantage of not being sensitive enough to detect the surface represented by minute cracks, the so-called internal surface of a particle. The low temperature krypton adsorption method described by Beebe1 utilizes apparatus and techniques that are essentially the same as those used in the ethane adsorption method."1° The surface area is calculated by the B.E.T. method."-' The krypton adsorption technique is particularly suited to the needs of the mineral engineer because: (1) The method can be used for making surface area measurements of rather coarse materials (35 to 48-mesh), as well as extremely fine materials, such as clays or colloidal slimes with specific surface that might be as high as 20 to 30 mb er g. (2) The use of krypton gas offers the advantage of low saturation pressures (2-3 mm) at the conveniently obtained liquid nitrogen temperature. Therefore the krypton vacuum system need not be designed to measure or withstand internal gas, pressures above one atmosphere as is the case with the nitrogen gas method. (3) The krypton technique offers the safety feature of employing liquid nitrogen, as contrasted to the ethane technique in which liquid oxygen is required. Furthermore, ethane vapor pressure at liquid oxygen temperatures is low (about 10 microns), and a high sensitivity McLeod gage is required for pressure readings. (4) The measurement technique with krypton gas is much simpler and faster, and the apparatus is less elaborate than that required with either nitrogen or ethane gases. Apparatus A krypton surface measurement apparatus like that used at M.I.T. is shown in Fig. 1. It is constructed of pyrex glass. A vacuum is maintained by two mercury diffusion pumps in series backed by a mechanical vacuum pump."' The vacuum thermocouple gage is used for checking the vacuum within the system. This type of gage is quite sensitive down to a pressure of 1 micron of mercury," but may be used to indicate pressures much lower than that

Jan 1, 1952

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By R. B. Basham, C. W. Macune

Very small anomalies in oil well temperatures are detected and measured by recording the difference in temperature existing between two thermally sensitive elements which are Spaced several feet apart on a small diameter carrier and lowered into the bore hole. The elements operate in a balanced electrical circuit, sending only a reference signal to the surface as long as normal gradient temperatures are encountered. When either element enters a temperature disturbance, the circuit is unbalanced and produces large recorder deflections for minute anomalies. The system is highly sensitive to small changes in thermal gradients caused by gas or fluid movements and to the boundaries between beds of different thermal conductivities. Typical logs show successful applications of the process to locating gas and water leaks in casing, gas entry. and gas-oil contact. INTRODUCTION Temperature measurements in oil wells have been made for many years in the search for additional sub-surface data. It has been generally agreed that many conditions in the bore hole cause temperature anomalies which, if located and measured, could yield useful information. But it has been recognized also that many of the irregularities, such as those produced by small water and gas leaks in casing, might be very small and therefore difficult to detect with certainty.' Although tem-perature measurements have been made which show anomalies of less than one degree deviation from normal gradient temperatures, the results are usually uncertain and unconvincing. The general practice, therefore. has been to apply temperature surveys only to well conditions known to produce appreciable disturbances, such as large gas movements and cement hydration. The recent demand for additional data has focused attention on the problem of making dependable temperature measurements in the many instances when anomalies are small but none the less significant. It was for the purpose of detecting these minute irregularities in bore hole temperature that the program described in the following text was undertaken. It is emphasized that this presentation is not offered as a complete study, for the process is still partially experimental. But it is believed that the results obtained thus far will be of interest to the industry and will indicate some of the system's potential usefulness. DIFFERENTIAL MEASUREMENT The chief value of differential measurement lies in the fact that a difference between two factors can be measured with a scale of values best suited to that difference, a scale that might be cumbersome or impractical if applied to the factors themselves. When it is known that all factors will be nearly equal in value, and therefore the differences consistently small, it is possible to select a scale which will permit very accurate measurement of the differences. This advantage is in contrast to the difficulty of measuring small increments of a single variable, where the increment must be measured by a large scale which is suitable for measuring the entire factor. Gradient temperatures are usually measured under this latter condition where temperature measuring apparatus must have a scale extending over the range of expected temperatures, say 50' to 25O°F, and it becomes almost impossible to detect small irregularities of less than one degree. The use of large strip chart recorders and divided multiple ranges tend to amplify the small anomaly and make it more pronounced. But the instability of instruments, both

Jan 1, 1952

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. I a shows the appearance of a piece of crude meerschaum from Turkey; Fig. lb a carved item; and Fig. lc, d, and e show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modem methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word meerschaum, from the German meaning "sea foam," was in earlier times used synonymously with sepiolite, a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time meerschaum was used as the commercial name, and sepiolite for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term meerschaum to the compact variety, and to use the term sepiolite as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication. Meerschaum typically is white to light gray, has a hardness of 2 to 2 ½ , conchoidal to irregular fracture, and specific gravity varying with porosity from about 2 to less than 1. The composition is somewhat variable,- but is near that determined by Schaller (1936) for sepiolite as 2MgO.3SiO2.4H2O. A more modern for mula based on X-ray determination of the crystal structure is given by Caillére and Henin (1961) as (Site) (Mg9)030(OH)6(0H2)46H20. The reason for the firm, compact nature of meerschaum, in contrast with the earthy variety of sepiolite, is not fully understood. It may be due to the presence of a very minor amount of some bonding material such as silica. Scanning electron microscope (SEM) photographs of a specimen from Turkey (Figs. lc-le) indicate that the meerschaum is composed predominantly, if not entirely, of crystalline fibers which merge into sheetlike forms in a complex, intertwined mass. Detailed X-ray and crystal structure data, as well as some data on thermal stability range, are given by Caillère and Hénin (1961) for the sepiolite family of minerals. Mode of Occurrence and Origin Most authors have attributed the origin of meerschaum to alteration of serpentine or other magnesian minerals. The occurrence in alluvium and other surficial deposits does not necessarily indicate that the alteration was supergene. In fact, hydrothermal origin appears more likely for some deposits, though not for all.

Jan 1, 1983

The sudden and untimely death of Dr. Charles R. Van Hise, late' president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people's university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise's contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise's death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920