Search Documents

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By Rob Farnfield, Charlie Adhock

The measurement of near-field shock has always been an attractive proposition for those working in the field of explosive and blast performance. The most commonly employed technique involves the use of piezoelectric accelerometers. Although highly effective, these complicated devices are relatively expensive and are often destroyed in the blast event. This paper describes the development and field-testing of a shock sensor of sufficiently low cost to enable it to be routinely used in product blasting. This new device is based on piezoelectric wafer technology and does not require any external signal conditioning. The device is housed in a small cylindrical package with approximate dimensions of 30mm (1.2”) length and 5mm (0.2”) diameter. It has been determined that the most effective way of fixing the device to rock is in a small diameter hole with epoxy glue. Alternatively the sensor can be simply placed in holes filled with either water or bulk emulsion explosive.

Jan 1, 2005

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

The Cadia Mine is located 25kms South West of Orange in the central west of New South Wales (NSW), Australia (Figure 1). Orange is a major regional centre with a population of 35,000 people. Cadia has a history of mining and exploration dating back to 1851 and shortly after the first Australian gold rush at Ophir, north of Orange. Newcrest Mining commenced an exploration program at Cadia Hill in 1992. This identified a substantial zone of copper and gold mineralization. Subsequent resource definition drilling defined an orebody with a mineable reserve of 200 million tonnes of ore with an average gold grade of 0.74g/t and 0.17\ copper. A full feasibility study commenced in 1994, approvals to proceed with development were granted in September 1996 and the processing plant was commissioned in July 1998. The project came in on budget at A$440 million and on time, 24 months from design to construction. The estimated operating cost at the time of commissioning was A$8.85/t of mill feed.

Jan 1, 1999

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By Michael J. Beus

This Bureau of Mines report describes a field experiment involving the sinking of two test shafts to directly compare the deformational behavior of circular and rectangular shapes. Results show that the circular shape is less sensitive to geologic discontinuities and applied stress field. Also, the rectangular shape is subject to a variety of behavioral modes, including beam bending and buckling. Geologic discontinuities around circular and rectangular shapes influence displacement significantly. Simple, two-dimensional elastic finite-element modeling, simulating circular and rectangular shapes in a biaxial stress field, shows that the structural response of a shaft is largely controlled by geologic structure. Consideration of anisotropy may be required for realistic analysis of a deep shaft.

Jan 1, 1985

By James A. Madonna

Information gathered while studying geological parameters that govern fine gold deposition in the a1luvial environment can be applied to the technological development and selection of fine gold recovery systems. It is recognized that substantial gold losses occur in the minus 1.5 mn (minus 12 mesh) fraction using conventional sluicing systems. Within the past two decades much attention has been given the design and efficiency of these thick bed concentrators. Studies and comparisons drew information from several foreign and domestic placer operations. These studies concentrated on: 1) the physical and chemical properties of alluvial gold 2) the parameters that control fine gold deposition 3) the geometrical form, components and general working structure of conventional sluicing systems 4) the physical properties which contribute to the overall efficiency of a sluice system 5) the comparison of three major styles of conventional sluicing systems. A dramatic improvement regarding fine gold recovery and water quality was observed when using modern multiple-channel sluicing systems in place of conventional single-channel sluicing systems.

Jan 1, 1988

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

Minera Escondida, located in the Antofagasta Region of northern Chile, is the world’s largest producer of copper as concentrate and SX-EW cathode. Projects to increase mill and flotation capacity began soon after start-up in 1990 to off-set decreasing copper grade. Subsequent projects had the objective to increase copper production through heap leach and SX-EW production and a second concentrator. The mine footprint concurrently expanded peripherally from the central high-grade enriched core of Escondida and then into the separate Escondida Norte deposit. Early in the mine life, metallurgical forecasting that was based on metallurgical composites of presumed ore types and historical plant production was adequate for operational planning, plant design, and project valuation. This approach became unreliable, however, as the increase in mine footprint was accompanied by an increased variability in key ore body characteristics such as hardness, copper-iron sulfide mineralogy, and sulfide liberation textures that were not reflected in the geological criteria used for ore type designation. The project study teams turned to small-scale physical and chemical tests to better characterize the spatial distribution of these key ore characteristics. Programs associated with capital growth projects were carried out through the mid-2000s to sample and construct a three-dimensional spatial model of hardness, copper sulfide mineralogy, and rougher flotation recovery from tests on 15-m drill core composites. Mathematical models were developed from the respective ore characteristic data to calculate throughput, flotation recovery, and concentrate copper grade. The spatial models were integrated with the concurrent mineral resource block model using standard geostatistical methods and the metallurgical process calculations were applied to the block estimates. The geometallurgical model, originally constructed on a project basis, is now managed by a dedicated team reporting to the manager of Geosciences & Resources Definition in the Escondida organization. The model has evolved with increasing complexity of the mine and processing plants and currently includes seven forecasting areas for three concentrators and four areas for two leach plants. Metallurgical forecasts of mill throughput, final flotation recovery, and concentrate copper grade still have the highest relevance to mine planning and optimization. Sample preparation, test procedures, and quality control methods are summarized for the ore characteristic tests important to these forecasts. Analytical results from recent annual sampling programs are presented for the hardness indices, rougher flotation recovery, and partial extraction copper analyses. Geostatistical analysis of the SAG mill hardness index is summarized as an example for the spatial estimation process. Mathematic models are presented for throughput (based on hardness indices), final flotation recovery (based on rougher recovery and plant calibration studies), and concentrate copper grade (based on sulfide mineralogy and empirical pyrite rejection studies).

Aug 31, 2023

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929