Search Documents

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

By W. W. Adams

[The s1xteeilth an.nual National Safety C mpeti t1on, concluc ted "by the Bureau of t4ine g, Un+ ~ed st tag' DepartIilent 0:1' the Interior, has jast been closed, and the results reveal t:'W.t. t_!e co~)eting comps.nies had fewer a.ccidents in proportion to the number. of !\1a..."1-h(J1J.l'~ :orkcd than in a:ny other yeex in the record of the contest. These annUk~l contestn are thus achieving the r purpose of promoting safety in tho minin induC'tr:r. ]

Jan 1, 1941

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

By D. William Tedder

Several bauxite residue sands and muds produced by Bayer plants in the U.S. and overseas have been fractionated using dry and wet magnetic separators. The magnetic sand fractions typically contain about 60 wt% iron and the bulk of the radioactivity in this waste. The muds are more difficult to process than the sands, but some fractionation is possible using a combination of flotation and magnetic separation techniques.

Jan 1, 1984

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

The extractive industry has been faced with a situation where there has been no systematic and formalised training and education structure available. Previous structures which were available, e.g. the quarrying diploma and the mining papers as a part of an engineering degree, have suffered the same fate as the Dodo. They are now extinct.   In providing for a training strategy, the past strategies need to be examined and reasons behind their demise examined. This paper examines the reasons for past failures in education and training in the extractives industry, the factors that need to be taken into account in creating an education and training culture, the strategies required, the Government regulations and trans-Tasman agreements, and the quality management which must surround the entire training programme.

Jan 1, 1997

By Peter G. Chamberlain

The surge in gold and silver prices during the 1970's attracted many new mining operators and has rekindled interest among experienced ones. With its low capital investment requirements and fast payout, leaching has attracted many operators--particularly those with small or low- grade deposits. Although in certain situations leaching offers many advantages over conventional mining methods, many operators are uncertain how these relatively new techniques should be implemented. Consequently the Bureau of Mines has prepared this circular to disseminate information on gold and silver leaching practices, techniques, and problem. Engineering data gathered from 26 operations indicate that most ores are leached in heaps following crushing and distribution on pads. Metal values are recovered from cyanide leach solutions using either zinc precipitation or charcoal adsorption. Potential problems that my hamper on block development of a leaching operation are poor percolation characteristics of the ore, calcium salt buildup, low temperatures, and solution losses. An extensive bibliography on gold and silver leaching is appended.

Jan 1, 1984

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By Chad W. Brown

"A study of five commercially available solvent-extraction diluents in combination with three commercially available extractants under sub-Saharan African copper solvent-extraction conditions yielded intriguing results. A variety of physical and chemical property analyses showed that the diluents have some property differences, but overall the properties are similar and provide comparable solvent-extraction performance. Although each physical chemical property technique provides useful information, no individual test result suffices for prediction of diluent performance. Furthermore, a diluent should be evaluated within the conditions for which it is targeted to determine a true measure of performance. Overall, the diluents studied possess appropriate physicochemical properties for sub-Sahara Africa copper solvent-extraction conditions and can be utilized to achieve efficient, safe and reliable operations. INTRODUCTION Background Today, commercial SX diluents are available globally from a limited number of manufacturers. Production quality and consistency of these diluents have improved tremendously over the past 20 years. For example, diluent flash points have been increased incrementally to improve transport and handling while reducing fire hazards. In addition, properties have been successfully modified to minimize evaporative losses, ultimately reducing SX plant raw material costs. Diluent manufacturers have also focused on meeting performance requirements of SX plants, including eliminating components detrimental to SX operations, such as olefinic groups that can react with various species resulting in changing phase-disengagement properties over time, as well as ensuring that proper hydrocarbon components are present within diluent mixtures to maintain good reagent–metal complex solubility. These challenges have been met in the midst of ever-increasing stringent environmental regulations. Sub-Saharan Africa copper SX operations pose a unique set of conditions for diluents due to inherent ore compositions and the associated high reagent concentrations required for complete copper extraction. Chevron Phillips Chemical Company, LP has been manufacturing hydrocarbons and hydrocarbon-based diluents since the mid-80s, applying this experience to identify the physical properties considered crucial for proper performance in SX operations. This paper documents the findings of a study utilizing commercially available diluents in combination with extraction reagents commonly utilized in African SX operations to evaluate the relative performance of the diluents under sub-Saharan Africa copper SX conditions."

Jan 1, 2015

By Jacob Masliyah, Zhiang Zhou, Dharamdat Christendat, Tshitende Kasongo, Kevin Hyland, Zhenghe Xu, Ted Kizior, Douglas Cox

"A novel on-line visualization system, previously developed at Syncrude Canada Ltd., has been modified to characterize rising bubbles, particles and particle-bubble aggregates in a flotation process. With this system, the bubble size and rise velocity in a laboratory flotation cell can be determined. The technique allows the loading of solids on bubbles to be visualized, thereby providing an in-depth understanding of sub-processes of flotation. A step-by-step data processing procedure is presented. The applicability of the developed system to mineral flotation and bitumen extraction is discussed. Under batch flotation conditions in a laboratory Denver cell, three main bubble-particle attachment patterns are observed. They are: i) single particles attached to single bubbles, ii) particle aggregates loaded on single bubbles; and iii) a group of particles aggregated with a group of bubbles. The results demonstrate that the on-line visualization system is a powerful tool for understanding and diagnosing flotation processes.INTRODUCTIONAir (Gas) bubbles are an indispensable component in a flotation system. Both industrial practice and theoretical analysis indicate (Yoon, 1993; Diaz-penafiel and Dobby, 1994) that the size and population of bubbles are two important process parameters in modeling flotation. More recent investigations (Finch, et al., 1999; Gorain, et al., 1997) suggest that for a given flotation system, bubble surface area flux, defined as the air liquid interfacial area per unit time and unit cross-sectional area of flotation cell, showed a better correlation with the flotation rate constant. As a result, the bubble surface area flux is now being considered as a key parameter to account for the combined effect of bubble size and population in evaluating the performance of flotation machines and modeling flotation processes. However, the success of using bubble surface area flux in flotation process modeling largely depends on how accurate it can be determined or estimated (Finch, et al., 1999)."

Jan 1, 2000

By AIME AIME

A JOINT meeting of the Canadian Institute of Mining and Metallurgy and the American Institute of Mining and Metallurgical Engineers was held at Spokane, Wash., and Cranbrook and Kimberley, B. C., on Oct. 13 to 16, 1926, with a total attendance at one or another or all of the meetings of about 300 members, ladies and guests. At the opening meeting, on Oct. 13, in the Davenport Hotel, Spokane, about 175 were present. The morning was occupied with addresses of welcome by M. H. Sullivan for the Columbia Section, who called on Mayor Charles A. Fleming, President John F. Davies for the Chamber of Commerce, and E. R. Hannibal, president of the Associated Engineers, each of whom heartily welcomed the visitors. Philip N. Moore, former president, and special representative of President Samuel A. Taylor, replied for the A.I.M.E., and Lewis Stockett, president, and Charles A. Banks, chairman, British Columbia Division, Canadian Institute of Mining and Metallurgy, and Henry M. Parks for the visiting A.I.M.E. sections, made appropriate responses on behalf of those they represented. The members and ladies had luncheon with the Associated Engineers. Philip N. Moore addressed the assembly on "The Opportunity of the Engineer"; an excerpt from his address appears on another page. At the afternoon meeting, with Lewis Stockett in the chair, Frank M. Smith was asked to make a brief statement of the proceedings of the Silver Producers Association in Denver. Supplementing his talk by placing a well-prepared statement on "Silver and the Plan of the Royal Commission on Indian Currency and Finance" in the hands of those present, he narrated what had been undertaken by the Silver Producers Association and what they hoped to accomplish.

Jan 1, 1926