Search Documents

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

The centrifugal elevator invented and patented by the writer is designed for the purpose of conveying the tailings of a gold dredge to such a distance that it shall not impede the dredging opperations. Formerly this was usually accomplished by means of a belt of buckets travelling round a ladder set at an angle of about 30 degrees to the horizontal, but this meant heavy wear and tear on the travelling buckets and the tumblers actuating them. The centrifugal elevator throws the tailings through the air to the required height and distance and it is manifest that during their flight from the elevator to the heap there is absolutely no wear and tear, only the attraction of gravity and the resistance of the air has to be overcome. All then there is left to he considered is how to throw the stuff with the minimun of prower and wear on the elevator.The elevator consists of a cam-shaped steel casting with a disc of mild steel plate on either side: These side plates project a few inches beyond the tips of the beaters, in order to prevent odd stones from straying in an undesired direction; they serve also to prevent extra large stones from reaching the beaters, for they slide off the rims into the water.

Jan 1, 1904

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By Nageswararao K

A series of tests was carried out on one of the rock-pebble milling circuits treating complex nickel ores at Kambalda Nickel Operations of Western Mining Corporation. A mathematical model to describe the behaviour of a 508 mm hydrocyclone was developed from the data.A "flat" reduced efficiency curve was observed for the system. This was attributed to a marked difference in the specific gravity of different size fractions of the feed. A modified approach in describing the shape or the reduced efficiency curve resulted in accurate prediction of the hydrocyclone performance.

Jan 1, 1981

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Moresby J. F

Segregation roasting was used to recover more than 85 per cent of copper from crushed, minus 14 mesh refractory furnace-lining bricks. A plus 14 mesh fraction: which was high in copper, could be recycled directly to the smelter, giving an overall recovery of approximately 90 per cent. An oxidation roast at about 700°C was necessary, before segregation roasting, to convert copper sulphides and copper metal to sulphates and oxides. Withsegregatron temperatures in the range 600°-650°C the quantities of solid carbon and NaCI required are 2-5 per cent and 1 per cent respectively. P.V.C. coating from scrap copper wire can be used instead of NaCl as asource of hydrogen chloride for the segregation reaction.

Jan 1, 1978

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By K. Goshtasbi

The mechanical behaviour of schistose sedimentary rocks such as slate show a great amount of anisotropy. Hence, the schistocity plane is essential when investigating the mechanical behaviour of such rocks. The presence of such rocks in civil projects causes non-symmetric deformation and their behaviour is unpredictable. In this research, the anisotropic strength behaviour of slates is studied. Uniaxial and triaxial tests were conducted on specimens having orientation angles (ß) of 0, 30, 45, 60, 75 and 90 degrees. The triaxial tests were done at confining pressures of 3, 5 and 10 MPa. The effect of anisotropy on uniaxial and triaxial strength, cohesion, angle of internal friction and Hoek and Brown's m and s constants were investigated. The results indicate that the strength of slates in uniaxial and triaxial compression exhibit a U-shaped anisotropic behaviour. In-order to evaluate the most suitable criterion for predicting the anisotropic strength of rocks in uniaxial and triaxial compression, an investigation was carried out on various criteria. In uniaxial compression, the Liao and Huong and Ramamurthy criteria had good agreements with the test results. In triaxial compression the Hoek and Brown and Mc Lamore criteria had better agreements with the test results. It should be noted that in-order to utilize these criteria, a large number of tests must be carried out. However, as the Ramamurthy criterion needs fewer test results, it can be the most suitable for investigating the behaviour of anisotropic rocks in triaxial compression. Keywords: Slate, anisotropy, schistose, failure criteria

Jan 1, 2006

IN accordance with a programme arranged by a committee of the Institute, consisting of Mr. William P. Shinn, of St. Louis, chairman, and Mr. Joseph D. Weeks, of Pittsburgh, secretary, the member's of the Institute, with their ladies and invited guests, assembled in Chicago on Sunday morning, August 22d. A special train, provided by the Chicago and Northwestern Railway,. left Chicago on Monday morning at 7.50 o'clock, and conveyed the party to Marquette, arriving at 9 o'clock P.M. Here the steamer Northern Queen, which had been chartered by the committee for the accommodation of the Institute, was in waiting, and the members and ladies at once took up their quarters on the boat. EXCURSIONS IN THE MARQUETTE IRON REGION. Local Committee. EXECUTIVE. -J. C. Morse, chairman; C. Y. Osburn, secretary ; D. F. Wadsworth, treasurer; C. H. Hall, H. Merry. RECEPTION.-S. P. Ely, J. P. Pendill, E. Breitung, W. F. Swift, A. P. Swineford, J. C. Fowle, C. G. Griffey. TRANSPORTATION.-Samuel Schoch, D. Morgan, D. H.. Merritt, J. Pickands. FINANCE.-Peter White, A. W. Maitland, W D. Rees, E. R. Hall. EXCURSIONS.-W. E. Dickinson, H. A. Burt, A.. Kidder, C. E. Wright. REFRESHMENTS.-J. Q. Adams, H. H. Stafford, Joseph Kirkpatrick, D. H. Bacon. On Tuesday the iron mines in the vicinity of Negaunee and Ishpeming were visited, transportation being provided by special trains on the Marquette, Houghton and Ontonagon Railroad. In the morning the McComber, South Jackson, and Jackson mines were inspected, and in the afternoon the Cleveland, New York, Lake Superior, and Barnum mines. Dinner was provided at Negaunee, and gracefully served by, the ladies of the town. In the evening the first session of the Institute was held in the saloon of the steamer. The President, William P. Shinn, of St. Louis, congratulated the Institute on the happy consummation of the wishes of its members to have a meeting on Lake Superior. After tedious and baffling negotiations arrangements had been com-

Jan 1, 1881

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993