Search Documents

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

Sedimentary pyrites from Tasmania have Se contents that are high for it province showing no overall Se enrichment. Sulphides from Devonian granitic rocks, and related cassiterite-sulphide deposits, Sn-Wand PbZn-Ag fissure veins have similar and relatively low Se contents, and pyrites from Devonian gold-quartz veins have very low Se contents. The high concentrations of Se at Mount Lyell are consistent with enrichment in pyritic Cu deposits in volcanic rocks elsewhere, and the dispersion of Se is consistent with a surface volcanic origin for several of the orebodies. In contrast, sulphides from Cambrian volcanic rocks and associated granitic rocks, and from the Rosebery and Hercules pyritic PbZn deposits, also believed to be of volcanic origin, are impoverished in Se.In the Mount Bischoff cassiterite-sulphide deposits there is no relationship between Se content of sulphides and temperature of formation as indicated by fluid inclusion studies, and sulphides from Devonian ores with different temperatures of formation have similar Se contents.The Se content of Tasmanian sulphides appears to be an unsatisfactory discriminant of their genesis and temperature of formation but in volcanic terrains may be a useful pathfinder for Cu concentrations.

Jan 1, 1969

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By Warren W. Krech

Rock property data is needed over a wide range of parameters for the optimum execution of rapid excavation research. Eight rock types were chosen by the Bureau of Mines for a standard rock suite for such research. Large rock blocks were quarried and the standard physical and mechanical properties measured and documented. The eight rock types that comprise the rock suite are Barre Granite, Berea Sandstone, Dresser basalt, Holston Limestone, Salem Lime-stone, Sioux Quartzite, St. Cloud Gray Granodiorite, and Westerly Granite. Geologic, petrographic, physical-property, and mechanical-property test data are reported for each rock type. The information is the first step in the building of a comprehensive property listing for the eight rock types. A limited number of rock cubes are available from the Bureau of Mines Twin Cities Mining Research Center for use by researchers to broaden the information available on the suite.

Jan 1, 1974

By H. Immink

Keywords: Kyoto Protocol, carbon credits, global warming, energy, auditing Climate change is nowadays being taken increasingly seriously, and the link between global warming and the carbon dioxide released in the generation of energy is coming under increasing scrutiny. The Kyoto Protocol was signed in 1997, after five years of negotiation. So far, about 84 countries have ratified this agreement, under which terms developed countries have strict targets linked to their 1990 level of emissions. However, ?greenhouse gas? (such as carbon dioxide) emissions continue to rise alarmingly. According to the World Resources Institute, greenhouse gas emissions in the USA increased 13% from 1990-2002, while Australia recorded a 22% increase. In contrast, the European Union, a Kyoto signatory, has seen a small decline in its emissions during the same period. This is led by the UK and Germany, who reduced their emissions by 15% and 19% respectively. The concept of ?carbon credits? provides a funding mechanism for companies in the developed world to compensate for some of their CO2 emissions by paying companies (trading credits) elsewhere in the world to undertake projects to bring about reductions in emissions. In the southern African mining industry, it will be possible to get refunded for undertaking voluntary emission-reduction projects. Concern about the environment is creating business opportunities. A preliminary calculation has shown that various projects in South Africa (those in the pipeline, with quite a high likelihood of coming off) could earn a combined total of about R2.5-billion, under the initial phase of the Kyoto Protocol's carbon-credit scheme, which allows developed-country companies to trade credits with developing countries. A number of local companies are planning projects that could comply with the Clean Development Mechanism (CDM), in which they will implement techniques to achieve certified emission reductions (CERs) of greenhouse gases. In order to prevent abuse of such a system involving vast sums of money, vigorous audits need to be carried out. A company has to prove it has made real changes and is not simply conducting business as usual under a cloak of claimed environmental improvements. PricewaterhouseCoopers has applied to become one of only a few international agencies that will be accredited to conduct validation and verification of the credits, by auditing what is called the ?designated operational entity?. An independent validator needs to confirm that the project meets the strict requirements of the Kyoto Protocol. The company has to demonstrate that it?s not business as usual. So, if you refurbished every five years, the next refurbishment is not a good CDM project, unless you can demonstrate that you will do something beyond the maintenance - that is what can be registered. So, Kyoto intends to get additional projects going, and the money for that is actually quite good - prices of 14 euros per ton of carbon dioxide not emitted have been seen. The price depends on who takes the risk for non-delivery if a project doesn?t deliver the emission reductions on time. The highly energy-intensive South African mining industry is heavily dependent on coal. There should be many opportunities for the pyrometallurgical industry to come up with creative ideas to reduce emissions, and there is now an additional financial incentive to encourage this. Companies can actually get money in return for doing these types of projects, in addition to the contribution to corporate social responsibility.

Jan 1, 2006

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

By C. Pelley, S. Kelebek, T. Katsabanis, B. Nanthakumar

"As part of a larger investigation on generation of fines from mining activities and their effect on downstream operations, ore samples from Onaping area stockpiles of Falconbridge Ltd were studied. Batch flotation tests were conducted on the stockpile samples and fresh ore samples to explore the effect of stockpiling on grade-recovery performance. Head grade and particle size distribution of the samples from stockpiles were adjusted so that the samples compared are similar to each other. In additional tests, fresh ore samples were blended with stockpile samples at various percentages, representing 27.4, 50.2 and 81.5% of stockpile samples.The samples from stockpiles produced inferior nickel grade-recovery curves compared to fresh ore. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to the nearly complete flotation of pyrrhotite. Secondly, while pyrrhotite from stockpiled ore became highly floatable, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite.In the case of blending, there was generally insignificant difference in the nickel grade-recovery between fresh and blended samples when the blending cases involved 27.4 and 50.2% stockpile samples. However, an increase in pyrrhotite recovery was observed for both blending cases. At 81.5% blending case, degraded grade-recovery was significant primarily due to the nearly complete flotation of pyrrhotite. There was a small, but noticeable amount of nickel loss for this case. However, for lower ratios of blending this loss was negligible.The increase in pyrrhotite recovery was partly attributed to its activation by Cu and Ni ions. Formation of a significant amount of elemental sulphur was also apparent from analysis of stockpiled samples. It can be concluded that pyrrhotite is mildly oxidized under stockpiling conditions while part of the pentlandite undergoes a more severe oxidation."

Jan 1, 2006

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

From time to time efforts have been made to classify rocks according to their hardness, toughness and abrasiveness, and to use these classifications to provide an indication of the ease or difficulty with which they may be drilled. However, rocks classified as of similar type on this basis may vary considerably in their .resistance to the penetration of a rock drill bit due to differences in their physical state.For instance, fine grained rocks of granular texture are more difficult to drill than equivalent' rocks of coarser structure, altered rocks drill more readily than unaltered ones, and silicified rocks usually exceedingly hard and tough may be so shattered by movement as to be drilled at a rate comparable to quite soft rocks. Therefore, considerable latitude has existed in this method of defining their drillability, and no values generally acceptable have materiaJised; so that, when the drilling properties of rocks are discussed, it is common practice to refer to their hardness or toughness in a greater or lesser degree depending to some extent on the emotional state of the drill runner.REFERENCES AND STANDARDSThe 'introduction of tungsten-carbide tipped rock-drill bits for use with percussion rock-drills has thrown increasing emphasis on the need for defining a rock's resistance to penetration in a more concise and generally acceptable...

Jan 1, 1950

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

By E. Roman, M. Brissette

"For its end of life, Kemess Mine processed its difficult-to-treat hypogene ore from the east pit, which is a lower grade copper and higher pyrite content gold ore. Metallurgical testwork showed that improvement was possible with finer grinding. In July 2010, small grinding media were introduced into the regrind mill resulting to a nearly 50% decrease of the power draw with a finer grind, an increase of 1.1% in the final copper grade, an increase of 1.2% in copper and 2.9% in gold recoveries at the cleaners. The overall recoveries of copper and gold increased by 0.6% and 1.3% respectively.INTRODUCTION Kemess Mine was located at 430 km North West of Prince George in North Central British Colombia. Its production started in May 1998 by Royal Oak Mines and was acquired by Northgate Exploration in 2000. Kemess reached its end of life production with its last of production on March 9th, 2011. The concentrator nominal capacity was 56,000 TPD consisting of a primary gyratory crusher feeding two identical conventional SAB circuits totalizing 35,840 kW available for grinding. Rougher flotation consists of four parallel rows of eight 130 m³ tank cells to produce a concentrate of 2% Cu and 6 gr/t Au which was pumped to a 5 m x 10.8 m regrind ball mill. The regrind installed power was 4,480 kW to generate a final grind of 80% passing 40 microns. This product fed the two stage cleaner flotation circuit, first stage being two parallel rows conventional 17 m³ Denver cells and second stage, two 3.3 m x 11.0 m flotation columns in series, designed and constructed by Kemess, to produce a 22% copper concentrate grade. The cleaner flotation middlings were returned back to the regrind mill (Froehling, Mohns, Roman & Grady, 2005; Froehling, Mohns, Rajwani & Fullam, 2007). The large copper-gold porphyry deposit was composed of 15% of oxidized supergene and leach cap ore and 85% of hypogene ore having three major alteration zones, mainly characterized by their sulphur/sulphide content. Chalcopyrite is the main copper mineral species with minor bornite. Gold was mainly present as free gold or electrum. The first alteration zone consisted of a phyllic alteration characterized by moderate and intense sericite alteration which had the highest mill throughput and twice the mine grade when in contact with the supergene horizon. The second zone consisted of a potassic alteration characterized by more competent groundmass and moderate to intense quartz stockwork which had a slightly lower mill throughput. Finally, a third alteration found beneath and on the east side of the deposit having almost no quartz stockwork and hardened groundmass, sulphide content is two to four times more. This zone had the lower mill throughput with significant drop in the mine average gold and copper grade. Through its mine life, the average life of mine copper head grade was 0.21% Cu and 0.64 gr/t Au. Head grades began to decrease from 2008 to be substantially lower in 2011 as shown in Table 1."

Jan 1, 2012

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By M. K. McCarter

Previous investigations suggest the possibility of determining shear strength of geologic materials by measuring the force necessary to rupture the web between two closely-spaced, parallel holes using a borehole jack. Current research using finite element modeling and laboratory testing of intact rock indicates that web failure initiates by tensile fracturing induced by a complex stress field. Based on these results, a theoretical justification for relating web strength with shear strength appears unlikely for holes of equal diameter spaced two diameters apart. Empirical results, however, show a strong correlation between average web strength and average unconfined compressive strength for some rock materials under laboratory conditions. A good correlation also exists between residual web strength and the residual angle of friction under the same conditions. This research project involves the construction and field testing of a large borehole jack. The jack is designed to operate within a conventional 12-1/4 inch rotary blasthole common to open pit mining. The system is capable of exerting approximately 800,000 pounds on curved platen measuring roughly 4x24 inches. Field tests indicate that the system will operate in a mining environment, and preliminary results suggest the possibility of using the force-displacement data generated by the jack to rank the competency of material within a mine bench.

Jan 1, 1982