Search Documents

To reduce the respirable dust generated by auger-type continuous coal mining machines. The Approach: Use water sprays close to the cutting bits on the auger so that coal fragments are thoroughly wetted as they are formed to prevent dust dispersal into the ventilating air. How It Works: The "wet auger" system of dust control uses water sprays distributed on both shafts of auger type continuous miners. This approach has been tested underground by personnel of the Bureau's Twin Cities (Minn.) Mining Research Center on a Wilcox Mark 20 continuous miner, in a cost sharing contract with Buchanan & Sons Coal Company, Inc. Personnel of the Interior Department's Mining Enforcement and Safety Administration collected dust samples and analyzed the data. A test machine was fitted with six sprays on each auger (see Fig. 1). Water flow rates from 8 to 12 gpm at pressures from 90 to 120 psi, or about 8 gallons per ton of coal mined, were required. At these rates of water usage, mining personnel experienced no problems with work-

Jan 1, 1974

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

Jan 1, 1883

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By George J. Carter

Data obtained from field and laboratory examinations were used by the Bureau of Mines to evaluate 82 silica deposits in the Pacific Northwest. A total of 94 field samples was taken from 64 deposits, and an additional 18 deposits were investigated that did not warrant sampling. Of the 37 deposits found to be of high quality, only 16 were large enough to be classified as industrial silica resources. Another 27 deposits did not meet quality requirements. Methods of simple low-cost beneficiation and rapid classification of a large number of samples were investigated in the laboratory. These tests indicated that high-intensity electromagnetic separation was equal or superior to either high-or low-intensity electrostatic separation. In general, the electromagnetic method gave higher recoveries and produced equal or better grade concentrates. A glass button method developed for estimating iron oxide content of silica samples proved to be highly satisfactory as a means of classifying field samples and evaluating beneficiation tests.

Jan 1, 1962

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By Saeed Salehi Malekshah

In hybrid foundation system or piled raft foundation (PRF), the raft has adequate bearing capacity and piles are usually required to ensure overall stability of foundation and also to act as settlement reducer for high rise structures. When piles are connected to the raft, a high axial stress may develop and one alternative is to disconnect the piles from raft and consider them as stiffeners for supporting soil. This system is known as disconnected piled raft foundation (DCPRF). Cushion, a compacted coarse grained soil layer, can be used beneath the raft to redistribute and adjust the stress ratio of piles to subsoil and plays an important role in mobilizing the bearing capacity of subsoil and modifying the load transfer mechanism of piles. In this study, finite element method (FEM) has been employed to investigate the effect of different parameters such as cushion stiffness, gap height, raft thickness and piling configuration on the behavior of disconnected piled raft foundation. The analysis is performed on different foundations of hypothetical and real case histories. Results indicate that increasing the raft thickness reduces the differential settlement and pile head axial stress. Concentrating the longer disconnected piles similar to connected ones beneath the central area of raft, decreases settlement of raft. With increasing cushion stiffness, vertical stress ratio of piles to subsoil increases, but settlement decreases. Increasing gap height from 0.1 m to 1 m decreases the vertical stress ratio of piles to subsoil.

Jan 1, 2011

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By David J. Kusler

This Bureau of Mines study is an appraisal of the demand for platinum, should this strategic metal be used as a. catalyst in the National abatement of automobile exhaust pollution. The Clean Air Act 0f 1970, as amended, requires that automobiles produced in 1975 and thereafter be provided with antipollutive measures to control automotive exhaust emissions. The study considers the need for automobile pollution control, the methodology for such control, the annual primary (new) platinum demand for automobiles produced from 1975 to 1990, primary platinum availability, and supply-demand forecasts and outlook. The correlative demand for platinum for the production of the required unleaded gasoline is also considered. Methodology for the study included a forecast of new automobile production from 1975 to 1990, development of automobile survival and retirement data, estimates of new platinum demand under various conditions of salvage, and data on recycling the precious metal from the catalytic converters of scrapped vehicles and existing vehicles when their spent converters are exchanged for replacement units. The new platinum demand for automobile exhaust converters, based on a converter service life of 50,000 miles, is estimated to be 1.41 million troy ounces initially in 1975, rising to 1.68 million in 1980, and declining curvi-linearly to 0.94 million in 1990. The platinum demand for converter longevities other than 50,000 miles can be derived from the tabular data presented. An appendix to the report presents a comparison between longevities of 50,000 miles and 25,000 miles. The petroleum industry's demand for new platinum for the production of lead-free gasolines could total as high as 1 million troy ounces between 1972 and 1981, just for expansion of isomerization and reforming capacity, and is in addition to normal operating demand for this metal.

Jan 1, 1972

THIS paper is the outcome of experiments carried on and experience gained. at the Waihi-Paeroa Gold Extraction Company's tailings plant at Waihi, New Zealand. The plant was erected to treat accumulated tailings which had been discharged into the Chinemuri River by the Waihi batteries.The Chinemuri River is a common sludge channel for all mining debris, tailings, and ashes from the power plants, the last being the cause of occasional high residues, which gave so much trouble to the management. The tailings were dredged from the bed of the river into barges by means of a Pohle air lift, the power being supplied: by a 13 b.h.p. Tangye oil engine driving an air compressor and a centrifugal pump. The sands were elevated from the barges by bucket-belt elevators over screens, to eliminate large particles and rubbish, into storage hoppers, and from there fed direct into four C. Judd Ltd. tube mills.The method of treatment was fine grinding in a weak cyanide solution, agitation in B. and M. tanks, filtration with turn-over vacuum filters, and precipitation with zinc shavings. The comparatively high values of the residues in gold gave a great deal of trouble, 'and it was not until repeated experiments were carried out that the cause of the trouble was located. While the value of silver residues remained stationary, the gold values...

Jan 1, 1912

By F. M. Vokes, P. M. Ihlen

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Ore deposition was related to three major stages: continental rifting and separation (Vendian-Late Cambrian), convergence (Late Cambrian-Early Silurian) and collision (Early Silurian-Devonian). The first stage included deposition of volcanogenic massive sulphide Zn-Cu and stratabound or stratiform Fe and Zn-Pb(-Cu) on continental margins, as well as less economic Nb and Fe in carbonatites, U, Mo, Ni and V in Alum Shales and orthomagmatic Cr, Fe-Ti and Ni(-Cu). The numerous volcanogenic massive sulphides formed during convergence included Early Ordovician Cu-Zn, mature-arc Cu, Zn, Pb and Fe-oxide deposits, Besshi-type deposits dominated by Cu or Zn in gabbro-intruded sediments and minor Cu-Ni(-PGE), Cu-Mo and skarn deposits. The collisional stage is represented by epigenetic deposits including sandstone Pb deposits (Pb, Zn, Ba, F and Cu) and minor vein deposits with variable Au, Ag, Pb, Cu, Zn, Fe, As, Sb, W and Mo

Jun 19, 1905

By Ian Holl, Adam Hempstock, Rickardo Welyhorsky, Niel Morrison

"The Victor Diamond Mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario and was completed approximately 9 months ahead of schedule.The Victor Mine process plant flowsheet was designed to produce a 95 - 98% by weight diamond concentrate. Main processing steps include 3 stages of comminution, dense medium separation and proprietary x-ray technology for final recovery. Reagent consumption for this process is limited to flocculant, for thickening of fine processed kimberlite, and FeSi for the dense medium separation.The commissioning phase of the Victor Project was executed over a period of 6 months and commenced prior to substantial completion of construction. The approach used was to focus on and complete commissioning of the higher risk dense medium separation and recovery systems prior to construction completion of up stream systems.INTRODUCTIONThe development of the Victor Diamond Mine took place over a period of approximately 5 years and had a capital cost of CAD997 million. It was a greenfields project in an undeveloped region of northern Ontario, only accessible by winter road. Figure 1, below, displays the location of the project within Ontario.The main stages of the project included feasibility, environmental permitting, engineering, construction, and commissioning. At the onset of the engineering phase, the mine was scheduled to enter production in October 2008. Through a team effort between AMEC and DeBeers Canada, the schedule was advanced by 6 months towards the goal of project completion in April 2008. Production status was attained in January 2008, approximately 9 months ahead of the original schedule. This paper focuses on the commissioning aspects of the project and includes a less detailed discussion of the engineering stage."

Jan 1, 2010