Search Documents

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By Sevket Acar, Tim Acton

"Zarafshan/Newmont is a 50/25/25 joint venture between Newmont Gold and the State Committee for Geology and Mineral Resources, and Navoi Mining and Metallurgical Combinat, two entities of the Republic of Uzbekistan. The Zarafshan/Newmont joint venture consists of a heap leaching operation which will process 220 million metric tonnes of existing low-grade oxide ore stockpiles (averaging 0.036 oz Au/t) from the Muruntau mine. Net recovery over the 17-year life of the project is expected to be 4.8 million ounces of gold.The plant construction started in October 1993 and operations commenced on May 25, 1995. The crushing plant consists of four stages of crushing and screening to produce a 95% passing 3.35 mm product, followed by heap leaching and gold recovery by the Merrill-Crowe process. The dore metal is refined at the Muruntau refinery. All gold produced by the joint venture is sold on the world market. IntroductionThe Muruntau mine and nearby town of Zarafshan are located in the center of the Kyzylkum desert, 250 miles west of Tashkent, capital of Uzbekistan. Following a mining conference in Moscow in 1990, a Newmont geologist was among the first team of westerners to visit the Muruntau Mine, the second largest gold producer in the former Soviet Union. At Muruntau, they found 220 million tonnes of low grade gold ore that had been stockpiled during the previous 25 years. In February, 1992, six months after Uzbekistan's independence, Newmont signed a 50/50 joint venture agreement with the Uzbek government to use heap leach technology to process the ore. The feasibility study was completed in November of 1992. Plant construction started in October, 1993 and operations commenced on May 25, 1995.Newmont Metallurgical Services performed metallurgical studies to obtain heap leach process design criteria parameters. The initial metallurgical study on 20 grab samples is the subject of this paper."

Jan 1, 1997

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By B. Valentim

The methodology used to obtain fly ash subsamples of different sizes is generally based on wet or dry sieving methods. However, the worth of such methods is not certain if the methodology applied is not mentioned in the analytical procedure. After performing a fly ash mechanical dry sieving, the authors compared those results with the ones obtained by laser diffraction on the same samples and found unacceptable discrepancies. A preliminary study of a wet sieving analysis carried out on an economizer fly ash sample showed that this method was more effective than the dry sieving. The importance of standardizing the way samples are handled, pretreated and presented to the instrument of analysis are suggested and interlaboratory reproducibility trials are needed to create a common standard methodology to obtain large amounts of fly ash size fraction subsamples.

Jan 1, 2008

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By P. G. Flood

A simplified conceptual model shows how the arc flank to arc fringe areas adjacent to ignimbritic centres form a prospective zone for natural zeolites. Large alkaline lakes that serve as the repository of voluminous ash-fall tuffaceous material provide the ideal chemical setting for pervasive alteration of silicic glass to zeolites. The unusually old age of the Escott deposit demonstrates that any silicic volcanic province that contains low-temperature, unmetamorphosed sequences is a potential zeolite exploration target and that age should not be used as a criterion to exclude potential areas. It has also been demonstrated that heulandite and mordenite, formed by diagenetic alteration of silicic glass, do not always change to analcite and albite through the ageing process

Jan 1, 1991

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By P. Dennis, T. Pieters, A. De Kievit, S. Ganguly

TEMCO has been producing manganese ferroalloys in submerged arc electric furnaces for over 40 years. The furnace linings all along have been of conventional insulation type until 2001 when a freeze lining of UCAR concept was installed for a 20 MW Furnace. Continuous improvement of furnace lining performance has been a key component in improving the business competitiveness of TEMCO. The expected minimum campaign life of the freeze lining is fifteen years as compared to the ten years of the conventional linings. The success of the freeze lining is very critical to the quanta and direction of heat flow through the lining that control the freeze protection. Under freeze protection can lead to reduced lining life and over freeze protection, on the other hand, can lead to operating difficulties and loss of smelting efficiency. It was, therefore, necessary to develop a computer based system to monitor and control the freeze protection. The computer based monitoring and control system uses the basic principles of heat transfer, activeX object and heat flux from dual thermocouples and that is reviewed.

Jan 1, 2004

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009