Search Documents

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By W. D. Northrop

This paper gives an account of the development of a technique whereby the vertical limits of geological horizons may be identified by the use of vertical variograms on the mineral of economic interest. This information may supplement or guide the correct subdivision of the individual horizons into meaning full data sets by diligent geological observation. This process then improves the quality of the variance modelling of the gold distribution in the plane of the individual layers and therefore enables better estimates to be made into the grids or blocks of the mine model. The technique is explained by an account of the development work, which was performed, on duplicate superimposed reef horizons in the Kimberley formations. The paper then shows how the correct approach was developed to evaluate the mineralized layers in a multiple stacked conglomerate layer sequence in the Elsburg reefs of the Witwatersrand Rand System at the Target deposit. The method of categorization of resources according to confidence in the estimate is also explained. The feasibility processes carried out on the three-dimensional model, in accordance with the SAMREC code are also described. An example of the development of a reconciliation process utilizing chip sampling is also explained.

Jan 1, 2003

By V. V. Nazimko, A. I. Hohotva, S. N. Alexandrov, V. P. Sazhnev, V. S. Zaharov

Ground behaviour in the vicinity of a roadway has been investigated using a physical model and in situ tests during a roof fall. It was discovered that behaviour of the ground is governed by irreversible displacements of adjacent rock clusters. The cluster is a short-living sector of a rock mass that moves as a solid body. For the lack of degree of freedom, the rock mass must be divided into clusters that are forced to move one after another in space and in time. These clusters permanently rearrange and reform during irreversible (inelastic) ground deformation. The crowded clusters have to yield to each other and alter their velocity and direction of movement to accommodate their motion into the excavation. Such behaviour involves uneven and irregular vertical deflection and the movement of adjacent rock blocks in the roof, sides and floor of an opening. Such movement destroys the symmetry of horizontal displacements with respect to the centre line of the opening. A set of indicators that a roof fall is imminent has been identified. Horizontal displacements and dilation must be controlled in order to maintain the stability of an underground opening. Such a state retains the self-supporting effect of the roof and contributes to rock bolts bearing capacity.

Jan 1, 2003

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By Jacques Deraisme

The technology of percussion drilling is well mastered. The lower cost of percussion drilling allows more holes to be drilled for the same budget. However significant differences are often observed between percussion and diamond drill assay data. This is due to the increased level of contamination associated with the percussion drilling process. Statistical studies on twinned drillholes show that diamond and percussion assays cannot simply be merged in a traditional kriging approach. The question then arises on how to use both types of data to produce reliable resource estimates. To take into account the lower reliability of the percussion assays, a noise characterized by a variance is added to these data. The methodology consists of two steps: 1. Cokriging of the equivalent diamond value at the percussion assay locations. 2. Block kriging using diamond assays and equivalent diamond values, calculated previously, adding to these data a noise, whose variance is the cokriging variance of step 1. This particular way of achieving kriging is called kriging with variance of measurement error. The paper illustrates this innovative methodology with an application on an iron deposit. The results of this method is compared to block kriging using only diamond assays and the gain in precision is quantified. An extension of that approach to multi-element cokriging is also presented.

Oct 1, 2009

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

By L. R. Plitt, A. J. Neale, B. C. Flintoff

"INTRODUCTIONThis is not a technical paper in the normal sense. It is an informal document which is intended to share the results of some recent cyclone research with our colleagues both in operations and in research.PILOT PLANT FACILITIESFigure 1 is a schematic of the closed circuit hydrocyclone pilot plant testing facility at the University of Alberta. In this figure the system is configured for some experimental work on wide angle cyclones which was recently completed. The rig is designed to study cyclones in the approximate range of 10 cm to 20 cm diameter. Notable features include the variable speed feed pump, the magnetic flowmeter and pressure sensors on the cyclone feed line and the travelling launder which permits simultaneous sampling of both product streams.ORGANIZATIONFor organizational convenience the subject matter has been divided into three parts:(1) Peculiar Partition Curves(2) Wide Angle Cyclones(3) Rope DischargePECULIAR PARTITION CURVESMuch of the initial empirical mathematical modelling work on cyclone classifiers dealt with homogeneous ores. A homogeneous ore is one in which all particles have substantially the same apparent density, or where one phase is very clearly predominant. In contrast, a heterogeneous ore is one in which there are at least two different density classes, each making a significant contribution to the ore composition. (Particle shape similarity is always assumed.)One of the problems which can arise when analysing the overall solids partition (selectivity, Tromp, etc ... ) curve for a heterogeneous ore is the peculiar shape which may be observed, when compared to partition curves for homogeneous ores. This is not an unusual occurrence and it has been documented by Lynch and Rao, Finch and Laplante and Larsen and Spring. The purpose of this section is to identify those operating conditions which may give rise to peculiar partition curves."

Jan 1, 1986

By Jun Yang, Zongshan Zou, Mei Qu, Jianjun Zuo

For technical renovation of the thermal plant, one frame structure workshop of 50,000 m2 (59,800 yd2) construction area and one reinforcement concrete chimney of 150m (492 ft) height shall be demolished by blasting at same time. The engineering environment of which is complicated and the accommodation space is limited. Therefore, the collapse sequence, direction, scope of the dismantled building must be accurately controlled to ensure the safe operation of the adjacent generator unit and transformer station. By taking technical measures of theoretical analysis and numerical simulation etc., as well as research on structures collapse method and detailed delay interval, it puts forward the technology of bidirectional folded collapse of the workshop and it uniquely adopts the initiation system that combined with “half-second delay inside drilling” and “millisecond delay outside drilling”. Additionally, by using of the integrated vibration reduction technology in combination of the blasting ruins, buffer ditch and damping ditch, it has safely accomplished the demolition blasting work in high efficiency. Besides the demolition blasting vibration signal is collected and analyzed. The success of the demolition blasting will become valuable reference to other similar works.

Jan 1, 2016

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents