Search Documents

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By G. A. Harrison

The introduction of extra low profile (XLP) mechanized equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations` incorporating injury-free production and cost-effective mining technologies. The method allows for the introduction of a suite of ultra-low profile equipment in narrow reef (1.2 m) stoping operations. For the first time it is now possible to achieve total trackless mechanization at these widths and indications are that XLP mining has the potential to add more value when benchmarked with conventional mining and low profile (1.8 m) room and pillar methods. Various mine layouts were tested at different sites within Anglo Platinum and the XLP breast mining layout proved to be the most effective. This paper describes the results of the trials at Waterval Shaft and concludes with recommendations on our future strategy on implementation of XLP technology within Anglo Platinum.

Jan 1, 2006

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

Orebodies are defined in economic terms in that they must satisfy conditions determined by costs of mining, extraction and marketing before being so described. Despite this they have an essential chemical character as specialized products resulting from geochemical differentiation, and it is surprising that so little basic geochemical research has been carried out with respect to ore occurrence and that prospecting methods based on geochemical principles are not more widely applied.Many exploration geologists associate geochemistry with analytical techniques applied to the detection of dispersed traces of metals from actual orebodies. Geochemical research, applied to economic geology, goes far beyond this limited field and the purpose of this paper is to discuss aspects of such research and its use in formulating exploration principles.THE GEOCHEMICAL BACKGROUND TO MINERAL OCCURRENCE AND EXPLORATIONThe three aspects of economic mineral deposits to which geochemical research can be of use in determining ore guides are genesis, control of deposition and mode of dispersion from orebodies after emplacement. Prospecting for mineral deposits is primarily based on theories of ore occurrence which deal with the genetic and depositional influences controlling localization of ore. There are many such theories and they will not be discussed here as they have been adequately reviewed in geological publications. Some are based on differing argument concerning the same empirically observed associations of ore. In this respect it is perhaps fortunate that they are not always mutually exclusive as regards the...

Jan 1, 1960

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By Sri C. Sawmliana, P. Pall Roy

Damage to underground roof and pillars in blasting gallery (BG) panels has been an increasingly important area of study in recent years due to the invention of new explosives and cord systems which has led to the modification and alteration of the design aspects developed by Charbonnage de France (CdF). According to extensive mine experiments conducted by Indian and foreign experts, it has been established that the induced peak particle velocity (PPV) is predominantly related to the emanated seismic energy of a source and the distance from the source. With that concept in mind, nearly 160 experimental blasts were carried out in four BG panels in India under varying geomining conditions. Based on the results obtained thus far, the authors have established predictor equations correlating explosive energy (in Joules) and distance from the shot to that of induced peak particle velocity received at the sensor point. Good correlation was obtained between the actual and the predicted values. It is realized that this equation may be used as an efficient tool to determine the size limit of blasts in BG panels so that the induced particle velocity does not create damage in underground workings as per the established Blast Damage Index (BDI) and other available safety norms.

Jan 1, 2004

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By W. H. Bassett, C. H. Davis

In the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-mm.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystal-lization of cold-worked alpha brass on annealing,l Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work. The first alloy was taken from regular mill stock that had been rolled from 0.580 in. to 0.376 in. (14.7 mm. to 9.5 mm.) gage, a reduction of 35.1 per cent. This bar (No. 1) had the following composition: Copper, 69.20 per cent.; zinc, 30.76 per cent.; lead, 0.02 per cent.; iron, 0.02 per cent. The second alloy was also taken from mill stock of 0.325 in. (8.25 mm.) gage and was rolled as shown in Table 1, in order to get four bars reduced two, four, six, and eight B. & 5. numbers respectively. This second alloy

Jan 1, 1919

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

By Terry J. Close

In 1985, at the request of the U.S. Bureau of Land Management, the U. S. Bureau of Mines studied part of the 56,623-acre South McCullough Mountains Wilderness Study Area (NV-050-435) in order to evaluate its identified mineral resources. The area studied is located in Clark County, NV, about 30 miles southwest of Boulder City. No mineral resources were identified. The study area contains the eastern part of the unorganized McCullough Mountain (McClanahan) mining district which has had no recorded production. Between 1911 and 1982, 23 lode claims were located in the part of the mining district that is in the study area; four of these claims are currently held by assessment (1986). A total of 11 mineral sites were found and examined during the U.S. Bureau of Mines investigations; 26 mine workings were examined. Of the 11 sites, four are within the study area, and seven are nearby. Of the seven nearby sites, six are adjacent to the west boundary and consist of precious-and base-metals bearing vein occurrences in metamorphic rocks. The seventh site is near the east study area boundary, and consists of a tungsten-bearing vein occurrence that is also in metamorphic rocks. The four sites within the study area consist of vein occurrences in metamorphic rocks that contain silver, gold, arsenic, lead, zinc, and copper. The veins at these four sites are too small and low grade to be classified resources; however, there are indications that three of the sites may have silver and gold resources at depth. Detailed delineation of the veins, and determinations of tonnages and grades are needed. This would entail additional mapping and sampling, trenching and drilling, and opening inaccessible workings.

Jan 1, 1987

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980