Search Documents

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By Alessandro Martins Duarte, Gabriela Patrícia Gomes, Christiano de Paula Boaventura, Hélio Braz Loss, Janeir Ribeiro Dutra

Para produção de aço em uma usina integrada o gusa líquido é parte predominante na composição da carga metálica, porém, levando em consideração a sua composição típica e para otimização do processo é necessário que haja um tratamento precedente ao carregamento do convertedor. Teores elevados de silício carregados em convertedores para produção de aço carbono e elétricos provocam um maior consumo de fundentes para neutralizar a sílica gerada durante o processo e maior instabilidade, por outro lado teores muito baixo não fornecem um balanço térmico favorável para utilização de sucata. Diante disso é necessário trabalhar com uma faixa de silício que atenda o mínimo necessário para que se tenha um balanço térmico favorável. Este projeto teve por objetivo modelar a dessiliciação através da adição de um agente dessiliciante e sopro de oxigênio na panela, trabalhando com um teor de silício final entre 0,20% a 0,50 %. A dessiliciação do gusa é realizada em 2 etapas, sendo a primeira quando o gusa é transferido do carro torpedo para a panela e a segunda etapa com sopro de oxigênio. O projeto conseguiu reduzir em 44% a quantidade de corridas fora da especificação, reduzindo dessa forma o consumo de fundentes no convertedor.

Oct 1, 2019

By Paulo Rodrigues dos Santos Junior, Alexander de Oliveira Botelho, Gustavo Maia de Almeida, Vinícius Antonio Ramos Pin, Daniel Cruz Cavalieri

A preocupação com a análise adequada dos resultados de retificação dos diferentes tipos de cilindros realizada na oficina é de grande importância para o processo de laminação. Sua classificação correta e de forma eficiente representa uma redução de custo e contribui para a estabilidade/continuidade do processo de produção de bobinas. Atualmente, na ArcelorMittal Tubarão, a interpretação destes resultados, assim como sua classificação, é realizada manualmente por retificadores que trabalham em regime de turno no púlpito de operação, a partir de dados gerados no final do processo de retificação pelos equipamentos denominados “retíficas”. Esse trabalho mostra o desenvolvimento e a aplicação de um sistema inteligente baseado em Lógica Fuzzy. Esse sistema objetiva a criação de um classificador automático da avaliação dos resultados de retificação como um guia operacional.

Oct 1, 2019

By Antônio César Freitas, Lucas Machado Barbosa de Faria

Este trabalho descreve o funcionamento do sistema automático desenvolvido para realizar o posicionamento de vagões durante a troca de rodeiros, que opera no Centro de Troca de Rodeiros – CTR, localizado nas instalações da empresa Vale em São Luís do Maranhão. O posicionamento de composições com até 110 vagões e com precisão de centímetros, resguardando a folgas entre vagões, é um desafio na rotina de manutenção. Para superar esse desafio foi desenvolvido um sistema automático para posicionar as composições de vagões, que utiliza medição baseada em tecnologia laser, com precisão de centímetros, e que atualiza continuamente a distância entre um rodeiro e o ponto correto de parada, possibilitando assim o posicionamento de rodeiros.

Oct 1, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Ismael Vemdrame Flores, Maurício Covcevich Bagatini, Otávio Henrique Matos de Assis

De modo a explorar o fenômeno de retardo de redução sobre a taxa de redução de cargas ferrosas no início da zona coesiva, testes de redução e de amolecimento e fusão, completos e interrompidos (nas temperaturas pré, 10 e 50% de contração), foram realizados para duas variedades de cargas ferrosas comumente utilizadas em altos-fornos: sínter e pelota. Os produtos dos experimentos interrompidos foram caracterizados fisicamente por meio de testes de densidade real, densidade aparente e porosidade (aberta, fechada e total). Os resultados obtidos mostraram que para as matérias-primas utilizadas o retardo de redução ocorreu em menor temperatura para a pelota, sendo também mais pronunciado. Por meio da análise dos resultados obtidos, foi possível verificar o aumento da porosidade aberta e total das cargas durante sua redução até níveis de contração de 10%. Para contrações de 50%, dentro do intervalo de retardo de redução, uma redução significativa da porosidade aberta para ambos os materiais foi observada.

Oct 1, 2019

By Roney Eduardo Lino, Loyslene Rabelo Fernandes, Gustavo Henrique Sousa, Athos Fernandes Araujo, Wallace Crisólogo Souza Gonçalves

Nos processos de refino dos aços, as ferroligas exercem um papel muito importante. E deve-se conhecer o comportamento do rendimento dessas ligas para que não sejam feitas adições desnecessárias que possam elevar os custos de produção ou até mesmo acarretar em perdas de corridas por composição química fora da faixa de especificação. Nesse trabalho foi utilizado o simulador de refino secundário do Steel University para avaliar o comportamento do rendimento das principais ferroligas em estação de rinsagem com banho metálico desoxidado ao alumínio e em banho não desoxidado. Foi possível avaliar que o comportamento do rendimento das ferroligas tende a ser mais positivo quando se é feita a desoxidação do banho metálico utilizando Alumínio briquetado. Com isso feito um comparativo do custo de produção que mostrou que, quando se conhece o comportamento dos rendimentos, é possível gerar economia para o processo.

Oct 1, 2019

By João Victor Gomes Guimarães Ananias, Itavahn Alves da Silva, Thiago Araújo Santos de Oliveira, Salvatore Giuliano Peixoto Tropia de Abreu, Guilherme Santiago Queiroz, Carlos Antônio da Silva

Oct 1, 2019

By Marcelo Ferreira Martins, Breno Totti Maia, Sandro Luís Zahner, Leandro Martins Perreira, Paulo Roberto Ogliari Hopperdizel, Geraldo Vieira da Silva

O reator EOF foi desenvolvido no Brasil nos anos 80 com características únicas. O pré-aquecedor de sucata e a distribuição dos pontos de injeção de gases oxidantes e combustíveis conferem estas características. Um reator dinâmico e versátil capaz de adequar-se a grandes variações de carregamento de gusa e sucata, porém com equipamentos de injeção calcados ainda nos princípios da concepção da tecnologia. O objetivo deste trabalho é apresentar a etapa 1 de uma seqüência planejada de 3 etapas os desenvolvimentos que visam o aumento de produtividade do EOF. Nessa etapa 1 são apresentadas os ganhos relativos a modificação do número de pontos de injeção de oxigênio e a adequação desses pontos para condição supersônica de sopro.

Oct 1, 2019

By Daniel Horta Fernandes, Walter Gomes de Albuquerque, Adriano Cesar Carvalhido, Victor Dias Martins

O trabalho apresenta a experiência recente da troca de 38 staves contribuindo no prolongamento da campanha operacional do Alto-Forno 3. Durante 13 dias ocorreu a substituição dos Staves originais de FoFo instalados em 1999 por novos Staves de cobre fundido. Além da recuperação do sistema de refrigeração, a mudança no material dos Staves contribui para maior troca térmica favorecendo a formação carga inativa (cascão) que protege os Staves e o corpo do Alto-Forno. Esta substituição foi fundamental para recuperar a estabilidade da temperatura da carcaça e prolongar a vida útil do equipamento até o final de sua campanha. Diversos aspectos do projeto serão apresentados: engenharia, metodologia, planejamento, segurança, qualidade técnica, cronograma e outros.

Oct 1, 2019

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Giulio Antunes de Medeiros, Leonardo Martins Silva, Giselle de Mattos Araújo, Rayla de Souza Caldas

To analyze the direct reduction of self-reducting briquettes producted with different electric arc furnace dust contents, three sets of homogeneous mixtures were produced with elephant grass biomass, iron ore, cement and furnace dust in increasing levels, which were submitted to thermogravimetric tests in muffle furnace and TGA furnace at variable temperatures and times. The curves of degree of reduction were obtained and the reduced briquettes were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the reducibility of the agglomerates is diminished by the increase of furnace dust, with variations of this result at higher temperatures. The observed microstructures were spherical particles, porous structure or whiskers. Based on XRD results, it was considered probable that the decrease of the degree of reduction with the increase of furnace dust content is related to the reaction between hematite and zincite, which is expected to be controlled by zinc diffusion.

Oct 1, 2019

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Joselito Gonsalves dos Santos, Ivani Batista dos Santos Junior, Valeria da Silva Guandelinir, Daniel Rocha de Castro, Alexandre Jose Ramos Valentim

Este artigo tem como objetivo demonstrar os ganhos obtidos com automatizações de atividades de suprimentos de média complexidade e alto tempo de execução. Para atingir o resultado sem investimento, foram desenvolvidas automatizações através de programação em Visual Basic (VBA) e Scripts SAP, utilizando como plataforma o Microsoft Excel. A integração do Excel com o SAP se mostrou eficaz, possibilitando a execução de tarefas de forma automatizada em massa, aumentando a confiabilidade das informações e reduzindo o tempo total de execução das atividades em 67%.

Oct 1, 2019

By Leonardo Semedo de Mattos Siqueira, Renata Ferreira Muller

The Granulometric Ratio (RG) is one of the most important indicators related to the pelletizing product. Through it, it guarantees good permeability of the bed of pellets, optimization of the thermal cycle and, thus, better results of physical quality and consumption of the energy matrix. To guarantee this indicator, it is necessary that the processes of agglomeration of pellets, classification of raw pellets and screening of burned pellets are under control of certain parameters and with a level of stability assured.

Oct 1, 2019

By Wujian jun

In the process of wire rod production, the rolled wire products must be cooled from the red-hot state to the normal temperature state. How to cool the wire rod after rolling is one of the key links of product quality control in the whole wire rod production process. In this paper, combined with the closed-loop transformation project of controlled cooling temperature of Xuanhuan iron and steel group co., LTD., the closed-loop related controlled cooling equipment (including water cooler, valve table, etc.), nozzle layout and process layout of water tank, and closed-loop software control system of controlled cooling temperature of high-line are analyzed and designed. Closed-loop system design USES temperature of cooling water cooling and water cooling two temperature closed loop regulating circuit, through temperature feedback and feedforward to achieve the uniformity of temperature adjustment, in order to prevent occur due to temperature closed loop control function with the phenomenon of a steel before and after the temperature difference is bigger, system Settings have "absolute temperature regulation" and "relative temperature regulation" selection mode. The system has a self-learning mode, which can modify the temperature feed forward formula. In addition, this paper takes the hard wire 82B rod as the test object, and studies the process parameters and the comprehensive mechanical properties of the rod before and after the water cooling system reform. The research results show that the temperature closed loop system, can ensure the rolled piece temperature control precision of plus or minus 10℃, enhances the stability of wire rod cleaner performance. It can reduce water consumption by about 186m3/h and improve the utilization rate of cooling water.

Oct 1, 2019