Search Documents

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By Takashi Sasaoka, Hiroshi Takamoto, Kikuo Matsui, Hideki Shimada

"Indonesia is the second largest coal exporter to Japan. Almost all the coal is produced from open cut mines. However, a great deal of coal is left in the highwalls of the mined-out pits. The use of highwall mining systems has increasingly come into play in the U.S. and Australia, when overburden depth exceeds economical recovery in an open cut mine. However, the stability of the highwalls is always a major safety concern in such mining. This paper describes the characteristics of the highwall mining system and discusses the appropriate highwall mining system for use in Indonesia.INTRODUCTIONIndonesia produces over 200 Mt of clean coal and is the second largest coal exporter to Japan, accounting for about 32 Mt of coal annually. Over 99% of the coal produced in Indonesia comes from surface mines. More open cut mines will be developed and more coal will be mined in order to fill the great demand both in Indonesia and the rest of the world.In open cut mines in Indonesia, there are many sites where mining operations have developed long highwalls that have been abandoned due to the current economics. Mining operations have been transferred to lower stripping ratio blocks of coal or overlying seams. In some cases, coal lies buried beneath spoil heaps or is covered with mud and water. It is estimated that there is a great deal of coal beneath abandoned and working highwalls. Considering these situations, it seems to be worth introducing highwall mining systems into Indonesian open cut mines.Final highwalls of open cut mines can form the starting point for other mining methods, such as highwall or underground mining. In its basic application, highwall mining is a technique utilized after an open cut portion of a reserve has been mined, sometimes prior to the introduction of underground mining (Seib, 1993). In this system, the coal seam is mined by remotely operated equipment, such as an auger machine or a modified continuous miner incorporated into a highwall mining system. The major problems with highwall mining systems are less coal recovery due to leaving coal as the pillars and the instability of openings and highwalls due to the pillar and roof failures."

Jan 1, 2010

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By Stephen C. Tadolini, Peter A. Gray, Robert Hawker, Andrew Sykes

"Self-drilling rock bolts (SDRBs) that use pumpable cement grout to anchor bolts have been used successfully in the tunnelling and civil engineering industries for many years. Pumpable cement grout offers a considerable advantage in that the SDRB can be fully encapsulated right down to the bearing plate, including filling cracks and cavities in the borehole. However, cement grout cannot provide the immediate rock support required for the coal industry. This paper describes a new SDRB system that uses pumpable resin to anchor the SDRB in a borehole, which not only provides all the advantages of a pumpable grout anchoring system, but also provides immediate roof and rib support as required in the coal industry. This paper further outlines the latest developments in SDRB technology including (1) extendable self-drilling rock bolts, which can almost double in length during the installation process and are particularly suited to low seam heights and rib support and (2) pre-tensioned SDRBs, where a pre-tensioned load can be applied during the installation process. These new SDRB systems offer both considerable advantages in rock support and improvements in mining productivity.INTRODUCTIONThe mining industry is continually striving to develop more efficient methods to support the roof and walls of roadways and tunnels, and rock bolting has proven to be one of the most significant improvements in ground support over the last 50 years. Rock bolting is now almost universally used in the underground mining industry worldwide, and there are many different rock bolts available.Rock bolts are traditionally made from steel or fiberglass and are anchored into a borehole with a friction-anchoring device, such as an expansion shell mechanism; cement grout; or chemical resin. Friction-anchored bolts are widely used in the Australian metal mining industry, predominantly as short-term support. They are used in conjunction with resin-anchored bolts where there is a requirement for longer life. Resin-anchored bolts are used in the coal mining industry.Friction-anchored bolts provide immediate rock support, but their load transfer capacity is poor compared to resin or cement anchored bolts. In addition, friction-anchored bolts are more susceptible to corrosion than resin or cement anchored bolts."

Jan 1, 2010

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Tobias U. Papst

The German Ruhrgebiet is slowly transitioning into a post-mining state. It has been subjected to industrial-grade hard coal mining operations for more than 150 years. Due to a political decision, German hard coal mining will come to an end in 2018. By then the surface will have subsided up to 20 meters. After all mining activities in the area have ended, there will be no need to maintain the current mine water level. Accordingly, the company operating the last remaining coal mines has decided to let the water level rise to an as yet undetermined level. Alongside other issues that may be caused by rising groundwater levels, the protection of the area?s drinking water supply is of utmost importance. This notion is also represented by European and German law. The primary intent of the applicable laws is to protect the health of the citizenship. This means protecting ground water that may be used by humans from being contaminated by the mine water. This paper outlines the consequences of European and German legislature on mining aftercare using the example of one of Europe?s largest agglomerations.

Jan 1, 2014

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The response of the surrounding rock mass to the creation of mining excavations determines the ultimate load on a pillar support system. In conditions where the ground is relatively soft and weak, the full overburden weight can be transferred to the pillar system. However, in stiffer and stronger rocks, a greater portion of the overburden load is transferred to the unmined coal barriers or abutments, and the pillar stress is reduced. This paper makes use of numerical models to examine the interaction between typical pillar systems and the surrounding rock mass for weak and strong geological conditions at various spans and depths of cover. The concepts of structural failure and functional failure of pillars are used to assess pillar performance when pillars are deformed beyond their peak resistance. The results show that the span-to-depth ratio is an important factor in determining the pillar stress and the ultimate deformation of pillars. The ultimate pillar strain appears to be closely related to the functional success of pillar systems.INTRODUCTIONThe National Institute for Occupational Safety and Health (NIOSH) was requested by Congress to study the safety of retreat pillar mining following the Crandall Canyon Mine disaster that took place near Price, Utah in August, 2007. As a part of this study, an investigation was made to better understand how the rock mass responds to the creation of mining excavations and how the loads are distributed among the pillars and the surrounding abutments or barriers. The outcome of these investigations contributed to the development of a modified loading model for the ARMPS-2010 (Mark, 2010) method ofretreat mining pillar design.Structural and Functional Failure of PillarsPillar design is typically conducted by estimating the pillar strength and stress, and then sizing the pillars so that an adequate margin of safety exists between the expected strength and stress. The pillar strength can be defined as the maximum resistance of a pillar to axial compression (Brady and Brown, 1985). If a pillar is loaded beyond its peak strength, load shedding or yielding can occur, and the pillar is considered to have failed as a structure. Structural failure generally refers to a loss of loadcarrying capacity."

Jan 1, 2010

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By Stanislaw Prusek

In this paper, results of underground measurements conducted in gateroad 3, seam 615, at the Bobrek-Centrum Colliery are presented. The Bobrek-Centrum Colliery is owned by Kompania Weglowa, the largest hard coal producer in the European Union. Yearly production at the colliery, including the longwall system, is about 2 million tonnes. Gateroad 3 was used simultaneously for two retreating longwall faces, No. 1 and No. 2. This working was also employed for the conveyor belt for longwall No. 1 and served as a transport road for longwall No. 2. Approximately 100 meters of gateroad 3 was maintained behind the face of longwall No.1 and then, with the progress of longwall No. 2, it was liquidated. In this paper, we present the results of underground measurements of vertical and horizontal convergence in gateroad 3. We also present the results of numerical modeling for deformation of the working. Finally, we analyse the accuracy of the numerical calculations by comparing them to the actual deformation of gateroad 3.

Jan 1, 2014

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017