Search Documents

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By H. Hoberg, M. Langen, B. Hamacher

Since the term "abandoned hazardous sites" was first coined in the 1978 environmental report of the Council of Environmental Specialists, a number of different types of technology has been developed in the Federal Republic of Germany for the remediation of contaminated soils /l/. At former sites of the mining industry, such as metallurgical and coking plants whose soil has been contaminated by organic and inorganic pollutants over decades of industrial activity, there is an exceeding necessity for soil remediation. Also, many former locations of metal processing works, battery factories or scrap yards have been contaminated in particular by heavy metals. Wet mechanical soil decontamination has proven successful over the past 10-15 years in the purification of these soils The process goal is the enrichment of the pollutants in certain plant products and the separation of a pollutant concentrate from the decontaminated soil. Table 1 lists the steps of the highly advanced wet mechanical soil decontamination process to achieve this process goal. Table 1 lists both the name of each process step and its goal in terms of a direct separation of the pollutant or the preparation of the soil for subsequent separation steps. For the separation of heavy metals, density sorting and separation techniques utilising flotation were specifically used. The use of chemical auxiliaries such as acids and lye is limited to special cases because these in themselves produce additional environmental impact and the economical effficiency of these techniques compared to conventional methods is lowered by supplementary process steps for water purification. The subject of this presentation is to consider how soil decontamination processes can be effectively improved through a description of the material properties of soils contaminated by heavy metals, and through carrying out basic investigations about the adsorption of heavy metals. Soils of different origins, especially those from former mining and metallurgical sites, were used for the experiments.

Jan 1, 1995

By F. Maciosek, D. Denton, J. Johnson

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and personnel from Coeur Silver Valley, Wallace, ID, conducted tests using rock strain strips and Split-Set rock bolts instrumented with strain gauges to monitor wall rock strain at the Galena Mine, Osburn, ID. The objective of the test was to identify whether strain on the rock bolts increased prior to a rock burst. Although results were inconclusive, researchers learned that the Split-Set rock bolts yielded in stick-slip fashion in the highly jointed walls of the stope. The bolts were also bent as stress was redistributed following blasting and subsequent movement along joints in the wall rocks.

Jan 1, 2004

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By J. Reed

The RockWorks EarthApps represent a free collection of 74 geology-related programs that read data from a built-in datasheet and create diagrams within Google Earth. EarthApps also includes programs that extract data from Google Earth. The programs that create diagrams include: point mapping (e.g. borehole locations), proportionally scaled icons (e.g. geochemistry), and strike & dip symbols. Line mapping utilities include; polylines, parabolas and pipelines. Polygon mapping programs include; thematic mapping (e.g. geology), mining claims, and public land survey sections. Image overlay capabilities include; draping (e.g. geologic maps) and time-based animations. Vertical image display capabilities are centered on either midpoints (e.g. drill-hole logs) or stretched between endpoints (e.g. cross-sections). The Flyover programs create virtual tours for site presentations. The cell-mapping includes a variety of algorithms (e.g. geochemical and geophysical contouring). Survey programs convert and export survey data to Google Earth as points and polygons. Programs that extract data from Google Earth include; points, lineations, polylines, and polygons. The RockWorks/EarthApps collection is developed by RockWare Incorporated based in Golden, Colorado.

Feb 27, 2013

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By Dirk van Zyl, S. Chander

Minerals have been critical to human society from the earliest and their use has been intertwined with the development of civilization. In the Western World, the mining, processing and extractive metallurgy associated with ores was first described in detail by Agricola in the 16th century. He considered these collective activities to be the most necessary and the most profitable of professions, and wrote, "without doubt, none of the arts is older than agriculture, but that of the metals is not less ancient; in fact they are at least equal and coeval, for no mortal man ever tilled a field without implements. In truth, in all works of agriculture, as in the other arts, implements are used which are made from metals, or which could not be made without the use of metals; for this reason the metals are of the greatest necessity to man." Ours is still a materials-dependent society that relies heavily on minerals for raw materials. Today our dependence on minerals is exceptionally great. To meet the need for fuel and non-fuel minerals in a representative year, in the United States alone, about one billion tons of coal and 2.7 billion tons of ore are mined. These mineral products are essential for fertilizers, for construction materials, metals and alloys, for manufacturing household and industrial items, for transportation, and for the generation of electric power. It is instructive to consider the diversity of uses found in our society for a single mineral product - silver, for example. Experts believe that in the past 5000 years we have mined about a million tons, or 31.9 billion troy ounces of silver. In 1988, 133 million troy ounces of silver were used in the Unites States. Most of the silver used was for techno- logical, medicinal and industrial purposes, Table 1. X-ray films, for example, carry comparatively large amounts of silver to lessen patient's radiation exposure. Silver does not prevent tooth decay, but each year about two million troy ounces of silver is used for dental work in the United States. In small quantities it is used in medicine. No metal - not even copper conducts heat and electricity so efficiently as silver. Silver wires lace solar cells, and silver oxide batteries power hearing aids, calculators, submarines and satellites. Hardened with tungsten or molybdenum, miniature discs of silver pass current from wire to wire in cars, telephones and computers. A dish- washer timer alone may have 50 such electrical contacts, which open and close without excessive heat or friction. Silver is an important component of solar reflectors, since no other material reflects light so well or uniformly. In our personal lives, silver remains in high esteem to adorn our tables, provide precious objects and jewelry. In many parts of the world, silver in the form of coins, jewelry and bullion is used for financial independence and security against the vagaries of paper currency. In India, silver is used in its purest form as thin foils to decorate sweets and other edibles. It is obvious that this mineral product, silver, is of great value and utility in our society. Minerals and Environment The benefits of minerals do not come without problems. Much of the silver, for example, lies locked up in copper, lead-zinc or precious metal ores; to extract it creates vast quantities of waste material. On the average, in order to recover one ounce of silver about a quarter ton of ore must be mined. To meet the world's annual demand for silver, approximately 100 million tons of waste is generated every Year. The problem with silver is repeated with all minerals. Conversion of mineral ores into usable materials necessitates the generation of large quantities of waste products that create tremendous disposal problems. In addition to waste material discarded during mining, wastes may be generated during processing as gases, liquids or solids that must be subsequently converted into forms more acceptable for disposal. Associated with the handling, treatment and management of waste products are a number of environmental problems. Environmental problems are not new to the minerals industry. In his Geographia, Strabo (63 B.C. - 20 A.D.), gives an account of the conditions of labor under which men

Jan 1, 1992

By Donald W. Gentry

This section deals with one of the most fascinating aspects of mining the evaluation of mine investment opportunities. Be-fore proceeding further, it is important to clarify the meaning of some fundamental terms used frequently in the text. 6.0.1.1 Mine Valuation vs. Evaluation The words "valuation" and "evaluation" in a mining context are often used interchangeably. However, for the purposes of this section, a distinction is made between the two terms in accordance with commonly accepted practice. The word valuation in a mining project context has the rather narrow meaning of placing a dollar or other currency value on the worth of the project as a whole. In other words, the value of a mining project refers to a measure of the desirability of ownership of that property. As such, the major item of interest is, "what is the mine worth?," or `what is the value of the mine?" The value of a mining project may actually be determined in the marketplace at any specific point in time, or it may be estimated by one of several methods. The topic of mine valuation is discussed in more detail in Chapter 6.1. The word evaluation in a mining project context connotes the broader meaning of determining the numerical values of all

Jan 1, 2008

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, NIOSH conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the research, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This document highlights NIOSH's research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers, and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan, and if appropriate training is provided. DISCLAIMER: ?The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.?

Jan 1, 2009

By K. Kavouridis

The energy and climate protection policy of European Union (EU), and its Member States adopted in 2007 bridges security of supply, environmental protection and competitiveness. The objectives of the EU energy and environmental strategy cover the foreseeable period till 2020. It assumes all sources of energy will be needed. The objectives for renewable and improved efficiency are ambitious; it must be established if they are also realistic. Coal can continue to make valuable contribution to the security of supply and low price of electricity, only with technologies allowing for drastic reduction of the CO2 emitted of its combustion. The aimed at -20% reduction of green-house gases (GHG) of EU-27 by 2020 is an objective limited in time and content. Europe produces less than 15% of global CO2 and this will be reduced to 10% in 2030. Emissions Trading (ET) is to remain the central instrument for CO2 management, especially in the power sector. ET scheme (ETS) or other mechanisms need designing to create an incentive for investment in higher efficiency and technologies and to Carbon Capture & Storage (CCS). The ETS as the climate protection instrument of the EU can become a heavy burden (high fuel and electricity prices, less security of supply) or it can create a climate for modernization of fossil fuel power plants. The suggestion in this paper of fuel-specific benchmark system for CO2 allocation after 2012 can combine the emission levels to be reached with a strong drive to invest, the necessary investment security, transparency and the principle of proportionality. A Benchmark System as recommended by coal industry could adapt to the different circumstances in the long term and comply with EU energy and environmental policy objectives.

Jan 1, 2008

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Mark E. Emerson

1967 will be remembered as the year the world realized it was running out of silver. In May of this year a new era in tin the history of the white metal was begun as the power of the U.S. Treasury to regulate world .silver markets was staggered by one of the most intense speculative flurries in recent times. In the past few months the price of silver has risen from $1, 29 to over $1.80 per troy ounce and with it have spiraled the prices of a host of silver-bearing consumer items. Legislation has, been enacted to conserve our coinage and meager silver stocks and today large quantities of non-existent silver are trading hands at a fast pace on the commodity exchanges throughout the world. Now that the price of silver has been set loose, forces are in motion to dull the world's appetite for silver. At the same time there is strong incentive to provide greater quantities of silver to satisfy the world's hunger' for the metal.

Jan 1, 1967

What is the preferred electrolytic cell design and why? Hall: Considerable research remains to be done on electrolytic cell design. Studies are presently being conducted to determine optimum voltage and amperage. Zadra cells, which were used in some of the first carbon plants, are efficient when properly installed. Gold and silver are deposited on large-capacity, cylindrical steel wool cathodes. At times high value sludge falls from the cathode to the bottom of the cell. Rectangular cells, which were developed at some smaller operations in Nevada, require less floor space and have some desirable features in that cathodes can be moved and sludge can be removed from cell bottoms without actually shutting down the circuit. In South Africa two types of cells using graphite and diaphragm configurations are being tested. Duncan: The rectangular cell has one problem it's easy for shortcircuiting to occur. If you don't have a good seal on the side of the tank and on the bottom, the solution is going to want to flow around the bottom and sides of the cathodes and you're going to get poor performance in the cell. That is the advantage the Zadra cell has over the rectangular cell. With good sealing, which is a must, you should be able to get a ratio of the value of the solution going in to the value of the solution coming out of 10 to 1. Ken, can you tell me what you're attaining on the Zadra? Hall: At the Homestake gold operation in Lead, the cathode in the No. 1 electrowinning cell is loaded to about 600 ounces when it is moved to the refinery. At this time the No. 2 cathode is moved to the No. 1 cell. The No. 3 cathode is moved to the No. 2 cell and a cathode with new steel wool is placed in the No. 3 cell. In rectangular cells this sometimes is not possible because the loading on the cathode in the last cell may be as high as that in the No. 1 cell. As Don has pointed out this can probably be prevented by good seal design between cathodes. Potter: At the risk of sounding as though I'm straddling the fence, I really believe that either the round cell, as developed by Jack Zadra, or the rectangular cell will do an acceptable job. The Zadra is a fine unit. Leaks are not unknown but there are not very many. However, the rectangular cell is very saving of floor space. Plastics have been greatly improved during the past year or two and there is a very efficient design for the rectangular cell. It would have six cathodes in it and contain about 25 ft of steel wool. The body of this rectangular cell would be reinforced fiberglass plastic but with an integral lining of a high temperature plastic. I think either cell is so efficient and reliable that I would almost be tempted to flip a coin depending on floor space requirements. Either cell can be used to pull a loaded cathode and to advance the lesser loaded cathodes. Don, what is the configuration of your cell? Duncan: The Pinson rectangular cell has dimensions 2 ft wide, 30 in deep, and 10 ft long-long enough to take a dozen cathodes and anodes. We are currently using six of each but are not up to full capacity as yet. It's a steel tank coated with rubber. We have copper bus bars, which brings to mind that the last cathode in the tank, in one instance, was loaded heavier than the first one. That was probably a function of poor contact between cathodes and the bus bar. You can have erosion of the bus bar and if you don't get current flowing into the anode and out of the cathode, the cells will not function properly. Kappes: Just a few comments on cell design. In an alcohol stripping circuit we are running in Beatty„ NV, we are using PVC pipes for all circuitry piping and a commercial polypropylene electrolytic cell. They seem to be working quite nicely. The cell itself has eight cathodes measuring 18 in2. At six gallons per minute flow into the cell, at an average gold content of about 500 ppm, we seem to get good loading on the first three to four cathodes and not much on the end cathodes. At 12 gallons a minute flow we seem to be seeing gold uniformly along all eight cathodes. We are running at quite a high amperage level, about 400 amps into that cell. Gene McClelland, US Bureau of Mines, Reno Research Center (from the floor): I was associated with a company where the packing density of their steel wool cathodes was much too high and created some short-circuiting problems in their electrowinning circuit. I would like to ask the panel if they can recommend a packing density for cathodes in pounds of steel wool per cubic foot. Hall: The weight of steel wool put on one of our cathodes is 10 lb and the dimensions of the cathode are such that density would be about 0.75 lb/ft3. Duncan: I made a rough calculation and I'm estimating about 2 lb/ft3. Potter: In checking over a number of electrowinning operations, I found apparently very satisfactory operation within the limits that have been mentioned. I have come to a figure of about 0.5-1.0 lb of medium grade steel wool per cubic foot packed as uniformly as possible, of course. One consideration in packing is the fact that there should be good contact between the steel wool and the conductor. Operators tend to compact the steel wool more than would be desirable just to try to maintain good contact.

Jan 10, 1981

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005