Search Documents

By Lester F. Sanford

Located in the Santa Cruz Mountains eight miles north of the City of Santa Cruz and inland from the coast, lies a typical beach sand consisting of quartz and feldspar grains of the Santa Harguerita formation of the middle tertiary age, Reserves of over twenty-five million tons of this sand form the deposit presently being harvested by Pacific Cement & Aggregates, a Division of Lone Star Cement Corporation. The deposit ranges from 350 to 700 feet above sea level and varies from two percent passing a 200 mesh screen to ten percent retained on a ¼ inch screen (see Figure '#l) In 1929 the first sand plant went into operation at this site. It was replaced by a new plant in 1937. This plant continued operation until the middle of 1965 when replaced by the modern plant described in this paper.

Jan 1, 1967

By M. P. Fahey

A significant amount of silca is recovered in the rougher stage of anionic flotation of Florida apatite. This recovery, in the past, has been attributed to both entrainment and cation activated flotation. This study shows that by using a transport factor, it is possible to determine the contribution of each mechanism towards silica recovery. Further, it is shown that the concentration of cations in the conditioning water significantly affects both the amount of silica recovered due to entrainment and true flotation. Further confirmation of this phenomenon was obtained by Ca++ doping of the conditioning water and by using a sodium silicate depressant.

Jan 1, 1996

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By Enrique Fernandez

The success of the excavation of a sewage tunnel in a very extreme geological conditions, from river deposits and sandy layers to hard dolomite, and several meters below the estuary under the sea water influence, shows that the choice of a right equipment together with the use of chemical products like foam and polymers enable to dig tunnels in unexpected areas and give solution to the environmental problems. The paper describes the excavation and support process as well as the adopted solutions in every material and during the cross through the intermediate shafts, also under sea influence.

Jan 1, 2003

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By A. F. MacDonald

The rugged foothills of the Allegheny Mountains in Washington County, Southwestern Pennsylvania, lend their terrain very well to the use of aerial tram systems to carry refuse from Bethlehem Mines' two preparation plants to disposal areas some distance from the plant site. Bethlehem Nines Corporation has three deep mines in this area, all of which are mining the Pittsburgh Coal Seam, The raw coal is prepared for metallurgical use in a preparation plant at each mine, Trio of these preparation plants, Mine No, 51, Ellsworth and Mine No. 58 Marianna, use aerial tram systems to dispose of reject material.

Jan 1, 1966

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By Marcus M. Key

Silicosis among metal miners is an ancient disease, probably as old as mining itself.' However, the primitive forms of mining were not productive of much silica dust, and the short life span of slaves used in mining probably precluded the development of more than a few sporadic cases of silicosis. Early diagnostic terms of miners' asthma and miners' phthisis suggested an occupational relationship and a tubercular component, but little attention was given to silicbsis until the turn of this century when epidemics of silico-tuberculosis arose due to the great expansion of the mining industry in the United States, especially silver and gold mining. The expansion was accompanied by mechanization and the introduction of pneumatic tools, which generated increasing amounts of fine silica dust. Mining communities were crowded and hygiene was poor.' The tubercle bacillus would probably have flourished even without the predisposition of silicosis.' As is so often the case in occupational health, biostatistical analyses first called attention to the problem, and environmental-medical studies later confirmed its existence. The bio-statistical analyses were occupational mortality statistics compiled by the Prudential Life Insurance Company in 1907, showing evidence of excessive mortality from tuberculosis and relationship to dust exposure. I The

Jan 1, 1971

By Henry N. McCarl

[ ]

Jan 1, 1966

By Richard H. De Voto

The Pb-Zn-Ag deposits within the Lower and Middle Paleozoic strata of central Colorado (Leadville, Gilman, Aspen, and others) occur principally in Late Mississippian karst-solution features within dolomites and, to a lesser extent, limestones. Several un- conformities within the Devonian and Mississippian carbonate rocks and the subregional dolomitization of the Leadville (Mississippian) Formation that occurred during the Late Mississippian resulted from recurrent uplift of elements of the Ancestral Sawatch, Gore, and Front Range areas within central Colorado. Uplift of these areas also strongly influenced the details of the extensive karst topography that developed during the Late Mississippian. In particular, uplift of the Sawatch Range area caused paleovalleys from 300-600 ft deep to form on the karst landscape. The pattern of karst-solution caverns, sinkholes, cutters, channelways, and breccia-rubble zones was strongly controlled by incision of surface drainages and the strong northeast-trending Mississippian joint system. These subterranean karst-solution features and breccia-rubble soil [ ] zones are the primary controls of the location of the Pb-Zn-Ag ore deposits in these rocks. In the Leadville and Aspen districts, the deeply incised paleovalleys occur immediately adjacent to the principal areas of mineralization. Pennsylvanian deposition of a thick terrigenous and evaporite sequence occurred within central Colorado in response to actively subsiding extensional basins and adjacent high-relief uplift areas. Hot brines developed within the Pennsylvanian strata, migrated laterally to, and moved upward vertically along, basin- margin faults during continued Pennsylvanian subsidence and deposition. These metal-rich brines migrated into karst-solution features within the Lower and Middle Paleozoic dolomites and limestones, principally within the Leadville Formation, in basin- edge uplifted locales where the Pb-Zn-Ag minerals were precipitated. Field relationships, mineral assemblages and paragenesis, fluid-inclusion data, and isotope studies suggest that the metals and brines were derived within the Pennsylvanian sedimentary sequence and that the ore minerals were deposited under different temperatures and at different depths from deposit to deposit. Chemical reaction with the carbonate cave sediment and wallrock, cooling of fluid temperatures, and mixing with meteoric ground waters were the probable combined causes of mineral deposition in the karst-solution features. Late Cretaceous-Tertiary intrusive activity has subsequently modified some of the primary Pb-Zn-Ag deposits in local areas.

Jan 1, 2013

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By Jan Jekielek

Increasing capacity of bulk material handling systems creates difficult problems for accurate in-line material weight measurements. At the same time increasing system complexity and growing user demands call for more measurements. Precision in-line weight measurements for bulk materials are usually accomplished by application of conveyor belt scales. Belt scale accuracies listed by scale vendors are applicable for ideal situations with suitable conveyor design, belt scale location and calibration means. This paper attempts to provide designers and users with simple means to evaluate belt scale accuracy for practical scale installations. Based on known mathematical models simplified formulas for measurement errors are derived and discussed. These formulas allow for simple determination of achievable accuracy for alternative scale installations on the conveyor, conveyor designs, etc.

Jan 1, 1979

By Robert H. Raring

Viewed abstractly, a mill may be defined as a mineral processing facility located somewhere between the mine and the tailings storage area, Just how mining operations and the demands of tailings storage affect mill design is, the subject of this paper. At the outset, it will be readily acknowledged that no two installations can, or ever will be the same. At one extreme is the bucket line dredge where the distance between the ?mine? and the tailings area is measured in terms of tens of feet. At the other extreme, the large open pit copper mines are frequently spread across twenty, miles or so of countryside with the ore moving to the mill, as exemplified by the operations at Bingham Canyon, Ray, or Ruth - the "upstream" counterparts of Garfield, Hayden and McGill. In each of these cases, mill location was largely determined by requirements for tailings storage and/or water supply.

Jan 1, 1961

By Frank C. Schora

The Institute of Gas Technology for many years has dedicated a large portion of its research effort to the development of a practical solid-fuel-based gasification process to produce a synthetic natural gas equivalent. The work is being done to prepare for the day when supplemental gas will be needed. This program, initially supported by the American Gas Association, and now by both the Department of Interior's Office of Coal Research and the American Gas Association, has developed the IGT Hydrogasification Process. This process, now entering the pilot plant stage, is based on the high-temperature, high- pressure hydrogenation of coal with a hydrogen-steam bearing gas. Product gas from this step is cleaned and catalytically methanated to produce a high-Btu gas. Estimated production costs indicate the process will be competitive with natural gas in certain areas of the country when required.

Jan 1, 1969

By B. Grosso

The National Italian Regulation concerning environment protection imposes that industrial areas are provided with systems aimed at preventing the circulation of contaminated groundwater. These systems can be static or dynamic and operate basically by intercepting the contaminated flow. Their effectiveness, realization time and costs depend on the intervention type and on the features of the specific site. The selection of the best solution is complex and the results obtained by this selection may be affected by residual risks related to the uncertainty of the hydrogeological and geotechnical characterization of the site. With regard to the industrial area of Portovesme, located in the south of Sardinia, the paper presents the analysis of alternative interventions aimed at the protection of the groundwater. The attention is focused on the evaluation of their effectiveness, impact on environment and, finally, time and costs of construction.

Jan 1, 2008

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959