Search Documents

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Shotcrete can be defined as spray-applied concrete with a maximum size aggregate in excess of 9.5 mm (0.375 in.). The concept evolved from guniting, which uses smaller aggregate and generally produces concrete with poorer physical properties. The larger aggregate used in shotcrete requires less water in the mix, while offering larger bonding surfaces, thus imparting greater tensile and compressive strengths. TYPES OF MACHINES Two basic designs of shotcrete machines in general use are the wet or prehydrated zero slump and low slump type, and the dry or nozzle hydrated machines. Fig. 1 shows a typical zero-slump machine in a con¬figuration commonly used for small-volume require¬ments. The prehydrated zero-slump machine mixes exactly proportioned batches in a sealed pressurized chamber. "Slugs" of hydrated shotcrete mix and com¬pressed air are sent through a distribution hose to the nozzle where the wet mix emerges as a spray. The spray is directed onto the rock surface by the nozzle operator. The low-slump machine is similar, except that a thick slurry mix of aggregate is delivered throughout the distribution hose to the nozzle. Fig. 2 shows a typical low-slump shotcrete machine used in moderate-volume applications. The nozzle-hydrated shotcrete machine accepts a premixed "dry" (4 to 6% moisture) batch of aggregate and cement. A constant feed of this mix is directed by compressed air through the distribution hose to the nozzle. At the nozzle, water for hydration is introduced into the emerging spray. The hydrated mixture is di¬rected onto the rock surface by the nozzle operator. Fig. 3 shows a typical dry-mix machine. The major difference between the two basic machine designs is the consistency of the shotcrete quality. Pre¬hydrated machines have high degrees of consistency and produce high-strength concrete, resulting from their ability to produce exact mixtures of zero or low-slump concrete within the machine. Nozzle-hydrated machines tend to produce poorer quality concrete because of the difficulty in controlling the water content at the nozzle. Water input essentially is an art. As such it is not precise, and the shotcrete produced is of variable quality. MATERIALS HANDLING Materials handling presents a problem to either type of shotcrete machine. At times considerable quantities

Jan 1, 1982

By Alexander N. Winchell

The construction and erection of the Coleraine concentrating plant was commenced in April, 1909, and was completed (with the machinery installed) ready for use in 1910. Attached to the main building is 'a table house large enough to accommodate con¬centrating tables for five units and space for a small machine shop and supply store. For the handling of the' railroad cars in the upper portion of the mill there is provided on the north side of the main structure a trestle approach 650 feet long, and on the south or opposite side a tail track 300 feet long. The latter is so constructed as to permit its being incorporated directly in a possible future extension of the plant. The building, viaduct approach and tail, trestle, as well as the table house, are con¬structed of steel, the total amount used being 6,100 tons. The building is covered by corrugated' steel sheeting over 2 x 6-inch wood sheathing fastened directly to the structural steel. The north end of the trestle approach is connected with the main road-beds forming the track system for delivery of the crude ore to the plant over an embankment of a maximum height of 110 feet containing over 2,000,000 cubic yards of dirt.

Jan 1, 1920

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicates the potential for scrap formation, validated through laboratory experiments with varying coke rate, basicity and holding time. The investigation discovered that smelting this combination could yield a metal product consisting of 59 percent Fe, 24.93 percent Cr, 7.56 percent Mn, 0.62 percent Ni and 0.93 percent Si. The optimum basicity was found to be 0.6 with 80 percent recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall carbon dioxide emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of US$330/t.

May 1, 2024

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By S. K. Kawatra

Three International Symposiums-the 14th International Minerals Processing Congress, the 17th APCOM, and the SME-AIME Fall Meeting special symposium on Design and Installation of Com¬minution Circuits-held in 1982 contained a number of papers relating to the fundamentals of processing coals and metallic minerals. In addition, many papers were published elsewhere in the literature. Some of the more significant papers are discussed below. Flavel reviewed key performance parameters, such as energy-size relationships for crushing processes and presented a fundamental basis for optimizing crusher productivity and possibly for development of improved crushers. Pascoe et al. reviewed the use of such control schemes. Magerowski and Karra presented a paper on a computer program developed to and in the design of crushing circuits. The problems associated with the scale-up to very large ball mills were discussed by Arbiter and Harris, and by Kavetsky and Whiten. Both groups concluded that limits on mill productivity arise due to problems associated with particle breakage and transport through mills. Austin et al., and Herbst and Rajamini reviewed the state of the art for the use of grinding circuit simulators for design and control. The effects of mill operating and design parameters on selection and breakage were discussed in detail. The philosophy of control and instrumentation for grinding circuits was extensively discussed by Kawatra and Seitz. Their paper presented for the first time an analytical basis for the inferential particle sizing technique and provided a fundamental basis for the implementation of this technique. The effect of reagent addition variation's on the performance of coal flotation circuits was reported by Kawatra and Waters, and on sulfide flotation circuits by Klimpel et al. Both groups analyzed circuit behavior from a kinetic point of view and reached similar conclusions on the effects of collectors and frothers. The computer simulation of an iron ore flotation circuit also was reported by Kawatra et al. In this work particular attention was paid to the phenomena of froth overloading. Klimpel et al., Kawatra and Waters, and Niemi et al. discussed the philosophy of control by flotation circuits from a fundamental kinetic point of view. An extension of the use of high intensity magnetic separators to the beneficiation of specular hematite was discussed by Thayer and Linkson.

Jan 5, 1983

By D. W. Scott, D. G. Minnes

Introduction Ontario's diverse industrial mineral resource base includes structural minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone, and dolostone. These resources are used to produce aggregates, brick, metallurgical stone, fillers, cement, lime, and other construction materials. The majority of the operations are in deposits of Palezoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were more than 140 Mt (154 million st) of aggregates produced in 1985. About 115 Mt (128 million st) of that was produced in southern Ontario with the rest being largely from Crown land in northern Ontario. Structural industrial minerals account for more than 80% of the value of total industrial mineral production. The remaining 20% is accounted for by the nonstructural minerals, such as salt, which is produced in the southwestern part of the province. A host of other nonstructural industrial minerals are known. Production, though, is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite, and byproduct metallurgical sulfur products (Fig. 1). Major production is close to the large markets of urbanized southern Ontario and the northeastern and northcentral US. With an abundant variety of industrial mineral resources and the large population within 650 km (400 miles) of most deposits, the market offers great potential. Ontario's nine million people accounted for about 35% of Canada's entire $476.3 billion gross domestic product in 1985. This equates to about one-third of the nation's buying power being within a 200-km (125-mile) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well-developed industrial minerals industry that fulfills most of the structural industrial minerals demand in Ontario. Nonstructural industrial minerals are similarly well placed to compete in this high demand area. Although Ontario manufacturers still import some of these materials, Ontario products are achieving significant market share. And, they serve the needs of neighboring provinces and states. Present production and trends Ontario has traditionally produced significant amounts of industrial minerals. This produc¬tion had a value of $956 million in 1984 (Table 1). Structural materials production in 1985 and 1986 approached or exceeded levels not seen since the early 1970s. Many new products have been developed using these raw materials. The industry is becoming concentrated in the hands of several large companies, mainly four large cement com-

Jan 12, 1987

By G. W. R. Kuzyk

The Underground Research Laboratory (URL) , a major geotechnical research facility, is currently being developed by Atomic Energy of Canada Limited (AECL) , 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program, which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Simmons, 1986). Comprehensive geotechnical research and development activities are being carried out in conjunction with excavation? and construction of the underground facilities.

Jan 1, 1989

By Walter E. Heinrichs

Early history of the district is typical of many, particularly in Southwestern United States. The usual early Spanish influence was felt; Marcos de Niza, Coronado and Father Kino are most notable, but authentic records regarding Spanish mining activities are sparse. About 1769 the Indian village of Tucson became a Spanish settlement. During the next century prospecting attempts were largely interrupted by the Indian, Mexican and Civil Wars. By 1870 Tucson had a population of 3200 and by 1880 the Southern Pacific Railroad extended all the way from Los Angeles. Pyrometasomatic copper ore was first produced with some local direct ore smelting done during the late 1800s. By 1907, a rail line was built from the Twin Buttes mines to Tucson by the Twin Buttes Mining and Smelting Company. World War I was a very active period, with mixed copper, lead, zinc, gold and silver production. This came mainly from underground replacement and contact metamorphic deposits and from practically all portions of the district. Some of these operations continued intermittently until the 1929 depression.

Jan 1, 1976

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

In subterranean mining operations, access to communication networks deep underground is critical for transporting data, voice and video, and other supporting applications that are essential for efficient and safe operations. Whether accessing sophisticated ERP or maintenance management systems, engaging in fleet management, video surveillance, or access control, or protecting miners with wireless locator systems, these networks serve as a literal lifeline between workers deep within mines and surface operations. For this, mining networks require more than permanently installed network cabling, it also requires unique deployable systems designed for quick installation, extension and even relocation as the active mine site area moves, or equipment is moved in and out.

Mar 1, 2014

By STEVEN J. SCHATZEL, Zoheir Khademian, KAYODE M. AJAYI

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine, creating safety concerns. To provide recommendations for developing guidelines that ensure a safe coexistence of longwall mining and unconventional shale gas production, this study uses a discrete fracture network (DFN) model to evaluate the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements.

Mar 1, 2023

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By Gabriel K. Nzulu, Lars Hultman, Per Eklund, Martin Magnuson, Abu Yaya, Prosper M. Nude, Hans Högberg

This study aims to identify individual elements and to gain an understanding of the surface reaction mechanisms, as well as the properties of precipitated pyrite particles observed during the hydrothermal formation of an ore deposit. A combination of X-ray diffraction (XRD), air annealing in a furnace, scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX), and X-ray photoelectron spectroscopy (XPS) was applied to investigate the crystal structure and identify the individual elements, permanence, transformation and chemical/electronic properties of such pyrite.

Jun 1, 2024

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By G. P. JADAUN, ANINDYA PAIN, Aditya Rana, SAURAV RUKHAIYAR, N. K. Bhagat

This study compares three different techniques — decision tree, artificial neural network (ANN) and multivariate regression analysis (MVRA) — for predicting blast-induced ground vibrations in some Indian tunneling projects. The models’ performance was also compared with site-specific conventional predictor equations. A database consisting of 137 vibration records was randomly divided into training and testing sets for model generation. The results indicate that the decision tree is best suited to predicting vibrations. Furthermore, the decision tree suggests that the intensity of near-field ground vibrations is mainly affected by the total charge fired in a round, whereas the intensity of far-field vibrations is governed by maximum charge per delay and charge per hole.