Search Documents

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By A. B. Cecala

The Bureau of Mines has been performing research to lower the dust exposure of workers at mineral processing operations for a number of years. This research has mainly been directed at source control techniques in an effort to lower a worker's dust exposure at a particular job function. In some cases, this control technology provided a carryover effect in lowering the exposure of workers at other locations, but for the most part had very little effect in lowering dust levels throughout an entire mill building. Recently, the Bureau became aware of several mineral processing operations having problems with high over-all mill dust levels. These operations were all using baghouse-type collectors to address their most serious dust contamination areas. Although these major dust sources were being controlled, there were numerous minor dust sources that were not. These minor dust sources were causing dust levels in these operations to gradually increase as the day or shift progressed. The intent of this work was to determine general guidelines and design criteria for operations that may be interested in implementing a total mill ventilation system. Most mill buildings can be considered a closed system and thus any dust that is not being controlled within the structure, will cause dust levels to gradually increase over the shift. A total mill ventilation system should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust laden areas throughout the mill structure. This air should be discharged at or near the top of the structure, where it is not a contaminant to plant personnel working outside. Without this exhaust system, dust can exit the building through open doors, windows, etc., and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. A total mill ventilation system is not a stand-alone technique, but is a supplemental technique to assist other localized dust control systems.

Jan 1, 1994

By D. K. Sengupta

Increased recycling of waste paper has been emphasized in recent years in both the USA and Canada for environmental and economic reasons. Removal of ink particles from the waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. Our study investigated the feasibility of a simplified flotation scheme which showed that about 90-92% ink removal can be achieved while 95-97% ink removal is achievable if a hydrophobic polymer is used ahead of flotation. The clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH, and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1993

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By Elżbieta Węglińska, Andrzej Leśniak

The earthquake locations are generally scattered mainly due to a simplified velocity model or seismic event picking errors. The aim of our research was to increase the resolution of the cloud of microseismic events recorded during mining activity in the Bobrek hard coal mine on the 3/503 coalface to delineate seismically active structures using unsupervised machine learning algorithms. We presented results of applying two completely different algorithms for reducing scatter in microseismic location to all events recorded during mining activity on the coalface - the collapsing (proposed by Jones and Stewart in 1997) and condensation (proposed by Kamer in 2015). The collapsing method simplifies the seismic cloud by shifting events inside their error ellipsoids towards local source densities. The error ellipsoids are determined by errors in the measured parameters and seismic network configuration. The advantage of the collapsing method is the partial elimination of blurring of the microseismic cloud. The condensation method reduces the size of the set of seismic events without changing the geometrical information. The reduction of the number of seismic events in the catalog takes place through the condensation of localized events with larger uncertainty into events with lower uncertainty. The spatio-temporal analysis of microseismic events was performed separately on two processed clouds – collapsed and condensed one. We examined how collapsing and condensation methods affect the automatic detection of clusters of microseismicity using density-based spatial clustering of application with noise algorithms. We compared structures detected by the machine learning algorithms in both seismic clouds first created by collapsing and second by the condensation. We identified structures created by mining activity and structures related to the local tectonics activated by mining. The presented results are essential for the prediction of future tremors induced by the mining operation and tectonics and thus ensuring safety in the mine.

Apr 26, 2022

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final' depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1997

By D. M. Larsen

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce done' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering. feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of verti¬cal autoclave units operating at 170°C (338F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By M. S. Duffy

To exploit the mineral resources of fine grained ore bodies the minerals processing industry is turning to fine grinding technology, of which tower milling has become an established part. However, compared to other mills relatively little is known about the operating mechanisms in tower mills. In all milling processes one of the keys to understanding how they work is in knowing how their grinding media move. To investigate the ball motion in tower mills a glass unit was therefore constructed and measurements taken of the movement of the grinding media. This paper describes the results from this study.

Jan 1, 1998

By Michael W. Glasson, Archie M. Richardson, Leo Gilbride, Laine Adair

Andalex Resources, Inc. recently engaged in a ventilation planning exercise that resulted in the construction of a new main fan installation to support longwall coal mining at the Aberdeen Mine. This paper documents the planning process, including underground measurements, modeling, permitting, and construction of the new fan installation.

Jan 1, 1997

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By Y. Luo, S. S. Peng

Several issues deserve further attention to improve subsidence prediction accuracy. These include: subsidence initiation and development over a setup entry area; subsidence development after face stop; and subsidence over chain pillar. An intensive subsidence monitoring program has been carried out over several longwall panels. A large amount of subsidence data has been collected, analyzed and solution techniques developed. In this paper, some of the measured data. data analysis techniques and the developed prediction methods are presented.

Jan 1, 1992

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972