Search Documents

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By J. D. Miller

The effects of operating variables on water transport to the over- flow, classification of hydrophilic particles and the recovery of copper and molybdenum from a low-grade porphyry ore are presented. Recoveries of copper and molybdenum exceeding 90 percent at a grade of 8 percent Cu and 0.2 percent Mo were realized for minus 100 mesh (1 49 µm) material at retention times of less than 500 milliseconds. The rapid rate of flotation and the effective separation of fine particles for an air sparged hydrocyclone appear to be due to directed interaction of particles in a high force field with numerous freshly formed small bubbles. This interaction occurs in the swirl flow developed by the system and is analyzed in terms of collision and induction time phenomena.

Jan 1, 1982

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By Jr. Koch

Since 1882, world zinc production has increased. In contrast, United States zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the United States, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in United States production are due to economic, not geological, factors. Recent exploration has located large mineable ore bodies; additional deposits will undoubtedly be found in the strata-bound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the United States is in an early stage of the production cycle for zinc. Of major mining districts in the United States, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district.

Jan 1, 1980

By Eudes Prado Lopes

The Mineral Resource Exploration Company - CPRM - a part-private, part-government concern jurisdictioned to the Ministry of Mines and Energy of Brazil, was founded in 1969 for the purpose of promoting the exploration of mineral and hydric resources throughout Brazil. The political-administrative framework within which it was conceived and created considering that an economic and financial balance to be maintained in all its fields of activity, CPRM set out right from the start to organize itself to perform -three basic lines of action, which can be summarized as follows: As a Service Company, to carry out those services requested by government agencies and by the private sector through of service contracts; As a Mining Company under the Brazilian Mining Code, aiming at supplementing private initiative, not beyond the field of mineral exploration;

Jan 1, 1975

By C. B. Kettering

In the early operations of the Inspiration Consolidated Copper Company, which extended from 1914 to 1926, the ore as mined contained principally sulphide copper minerals, manly chalcocite (Cu2S), This ore was milled in a 20,000-ton concentrator and the copper was recovered as a flotation concentrate which, was smelted at the nearby plant of the I ternational Smelting and Refining Company. In those days no attempt was made torecovercopper from any oxide minerals present. As mining operations progressed it soon became evident that the proportion of oxide minerals present would steadily increase, and. it was realized that some method of treatment would have to be developed whereby copper could' be recovered from both oxide and. sulphide minerals contained in the ore. A research program was instituted and after some years of experimental and, pilot plant work a new hydro-metallurgical process was developed whereby it became possible to extract copper from both the oxide and. sulphide minerals in a single leaching operation. The solvent adopted consisted of a mixture of sulphuric acid and ferric sulphate,' Following dissolution, the dissolved copper would be recovered by electrolysis. Also in the process of electrolyzing, spent solutions of sulphuric acid, H2SO4, and. ferric sulphate, Fe2(SOk)3, would be regeneratede and. somade available for continuous reuse. The process appeared to be a success and the decision was made to build a full-sized leaching plant for the future treatment of I spiration mixed ore. Construction was started and the leaching plant was completed in 1926, With the start of ferric-sulphate leaching the Inspiration Concentrator was shut down and, with the exception of a few short time runs has not operated since that time. The ferric sulphate leaching process served. Inspiration well for some 30 years and during that time won a name for itself as a classic example of hydro-metallurgical treatment of mixed sulphide oxide ores. Originally the plant was designed. to process some 7,500 tons per day of a mixed ore containing about 1,2% copper, of which 60% was present as oxide and. 40% as sulphide, Down through the years various improvements were made for the purpose of increasing plant capacity and as well to change the limiting 'factor of sulphide-oxide ratio, The final result was a leaching capacity of 9,600 tons per day when treating a 1% copper ore with a reversal of the sulphide-oxide ratio to 60% sulphide and 40% oxide.

Jan 1, 1958

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Thomas J. Peters

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral investigation of about 85,470 acres of the Diablo Mountain Wilderness Study Area, to determine mineral resources and mineral resource potential. The study area is in Lake County Oregon, about 45 miles northwest of Lakeview. Fieldwork was conducted in 1986, 1988, and 1989. Geologically, the study area lies on the northwest edge of the Basin and Range physiographic province, a region of fault block-formed mountains and basins characterized by interior drainage. Consolidated rocks are mostly Tertiary basalt and tuffaceous sedimentary rocks. Low-lying areas are covered by Quaternary alluvial-fan, sand-dune, playa, lacustrine, and landslide deposits. The principal structural features are normal faults that have large vertical offsets; these faults are typically concentrated at the margins of large horst and graben. The 34,310-acre "additional," or western part of the area was mainly studied in 1988 and borders the east shore of saline Summer Lake. In this portion of the study area there is potential for undiscovered resources of soda ash, boron compounds, and sodium sulfate as well as by-products, which include magnesium compounds, salts, potash, bromine, lithium, and tungsten associated with brines. No energy or mineral resources were identified in the study area, but brines within lake and playa sediments contain concentrations of chemical components suitable for the production of soda ash, boron compounds, and sodium sulfate. Possible by-products include potash, salts, bromine, lithium, magnesium compounds, and tungsten. Limestone from the study area could be used in the recovery process of brine components or agricultural uses. The study area includes thermal springs and lies within 2 miles of the Summer Lake Known Geothermal Resource Area. Local production of geothermal power by the binary process may be economically feasible. Soda ash, soda ash products, and boric acid are widely used in fluxing metals, and have important applications and markets in the aluminum industry in the northwest and the developing Chinese counterpart. Evaporite commodities are essential to many "backbone" industries, and to many new applications and advanced materials. Markets for brine mineral products appear to be undergoing steady and strong growth, especially in the Pacific Northwest and in Pacific Rim countries. Soda ash produced near the study area would be 55 percent closer by rail to marine export at Portland, Oregon, than trona deposits of the Green River District (Wyoming). Soda ash and a daughter product, caustic soda, and sodium borohydride will receive increased application in the bleaching of paper pulp for environmental reasons. Caustic soda, used in many industrial processes, is more environmentally friendly when derived from soda ash than when produced from sodium chloride salt, because of the absence of a chlorine by-product. Producing soda ash from brines, a type of in situ" mining, can be done with minimal environmental degradation, and mining natural soda ash is environmentally as well as economically preferable to synthetic soda ash production.

Jan 1, 1995

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By M. Gunter, M. Buzon, B. McNamee

"A Google search on talc asbestos will yield over 500,000 hits – the reason being the growing number of civil lawsuits in this area. Historically the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos. Ultramafic hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc; they can occur in the surrounding black-wall, also the serpentinite host rock is in direct contact with the talc. Thus allegations can be made non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. INTRODUCTION Gunter (1994) wrote the following in regard to the question “What is asbestos? “The question yields different answers depending upon the audience. To a mineralogist, asbestos is a mineral form. To an engineer, it is an industrial material with several useful properties. To a medical doctor, it is an agent that might cause certain diseases. The third answer invokes several more issues: to a lawyer, a possible lawsuit; to a news reporter, a story; to an asbestos abatement worker, a job; and to a public school administrator or a parent, a nightmare.” The main function of that article was to try and provide background information to be taught at the college level to help students understand some of the issues associated with the use of asbestos in our modern society, and especially its use as a fireproofing agent in schools and public buildings. At that point in time one of the main issues was asbestos abatement as the mining and use of asbestos was waning as its health risks became more clearly known in the occupational setting. Now over 20 years later the current issue we are dealing with herein is “asbestos” occurring naturally in talc. This is a well know concern for those in the talc industry and they have been working on methods to ascertain if their products contained “asbestos” since last century. As such our articles will focus more on issues emerging from recent litigation, and the confusion that occurs, especially in the “asbestos” nomenclature as the mineralogist, engineers, doctors, and lawyers previously mentioned try to communicate. And lastly we need to remain cognizant of the fact that people are still dying of mesothelioma in the US. As a last resort to recoup expenses as they are dying they often respond to the TV advertisements we’ve all no doubt seen."

Jan 1, 2016

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

As noted by D.W. Fuerstenau in his Plenary Lecture at the Conference on Extractive Metallurgy of Gold and Base Metals, Kalgoorlie, Australia, "Com¬minution of solids is surely one of the oldest technologies that, even in this day and age of DNAs, chips and space exploration, continues to challenge our scientific acumen and engineering ingenuity." Thus, the fundamentals of comminution continue to receive a great deal of attention in the literature. This was particularly true in 1992 with the publication of the proceedings from the SME-sponsored symposium, Comminution Theory and Practice. Papers covering topics ranging from liberation to comminution fundamentals to novel size reduction techniques are included in this review. Liberation Liberation continued to be a prime area of research interest, not only in terms of liberation modeling, but also in understanding the basic mechanisms involved in mineral liberation. King (Comminution - Theory and Practice, pp. 3-15) described a method for determining the interphase area between mineral grains. He showed how the mea¬surement of interphase area before and after comminution could be used to determine the presence or absence of intergranular fracture. Lin, Miller and Cortes (Kona, Vol. 7) discussed the use of computed tomography (CT) as a nondestructive means of investigating three-dimensional particle composition. The use of this technique in constructing coal washability curves from CT data was presented.

Jan 1, 1993

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By R. J. Mirville

Flocculation is an important step in the treatment of coal preparation waste waters. The effects of polymer charge and molecular weight and solution pH and ionic strength on the adsorption and flocculation characteristics of a series of polymeric flocculants on some typical waste water constituents have been studied experimentally. The results indicate that the nature and extent of flocculation are strongly system-dependent. For the case of coal, both adsorption and flocculation behavior can be correlated with the polymer conformation in solution. For the mineral constituents, on the other hand, adsorption and flocculation depend also on the surface properties of the solid.

Jan 1, 1979

By R. W. Salmi

The authors discuss the cooperative efforts by Minnesota Ore. Operations and Research; from the earlier development, testing and installation of fine shear screens in the Minntac Step III concentrator to the most recent testing and operating data that has resulted in the installation of Derrick Multifeed sandwich deck screens in Minntac Steps I and II. Pilot-plant test results that were obtained at the Coleraine, Minnesota Research Laboratory are also reported and demonstrate the effects of feed rate and feed percent solids on sandwich screen performance with two sizes of Minntac fine screen feed.

Jan 1, 1984

By Daniel R. Shawe

Epigenetic ore deposits in Nevada and Utah occur in clusters or belts in a variety of tectonic settings. Many are concentrated in the western half of Nevada in a region containing numerous, relatively large intrusive bodies. Throughout Nevada and Utah, they tend to be clustered in elongate zones or belts. Some of these belts are well defined by the distribution of mineral deposits, patterns of igneous rocks, alinements of faults, and aeromagnetic anomalies, whereas others are equivocal. The Pioche belt in eastern Nevada and western Utah, the Eureka belt in central Nevada, and the Manhattan belt in western Nevada exemplify the general characteristics of these belts, the close relation of some belts to geologic structure, and the lack of a clear correspondence in other belts. Some of these belts are characterized by alined or en echelon faults that disrupt the north-trending Basin ranges, by belts of Cretaceous and Tertiary granitoid and porphyry intrusive rocks near which the ore deposits occur, and by alined magnetic anomalies generally related to the Cretaceous and Tertiary intrusive rocks. All the mineral belts have produced precious and base metals and tungsten; the Manhattan belt in addition has produced magnesite and brucite; and the Pioche belt, uranium, fluorspar, and alunite. The belts in Nevada and Utah may be related to a variety of factors, such as zones of structural weakness in Precambrian rocks, transverse zones of lateral faulting, localized areas of igneous activity, or a combination of these and other factors. Specific types of ore deposits in Nevada and Utah seem related compositionally to the intrusive bodies with which they are associated. Iron deposits, for example, are associated with mafic intrusive rocks such as diorite or gabbro, whereas copper deposits generally and tungsten deposits almost exclusively are associated with granitic intrusive rocks such as quartz monzonltc and granodiorite.

Jan 1, 1976