Search Documents

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

Improvements in computer technology and associated software have allowed the improvement and development of more advanced ventilation modeling software packages including those that have the ability to simulate the effects of a mine fire on the ventilation system in terms of heat, smoke and gas distribution. This ability has real applications for the mining industry in terms of emergency planning, training and response. The primary focus of this paper will be the benefits to training programs that this type of software can provide to all types of training for various personnel, from the newly hired inexperienced miner, mine rescue, atmospheric monitoring personnel and emergency evacuation drills. The results of the simulations can then be used to give miner?s more detailed information on what types of conditions they may face based on the type and location of the fire and the program itself can be used to manipulate the ventilation system in a way that emergency response personnel may (i.e. tear down stoppings to reduce airflow to the fire area) and see the effects in real-time.

Jan 1, 2012

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By H. Cho

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal organic components could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation is dependent on the history of coal: the extent of liberation decreased when the size of the primogeniture coal decreased. The liberation of coal macerals was analyzed by examining the Liberation Index. It was seen that although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinitie), these particles were less liberated than the coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1996

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991