Search Documents

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

By G. W. Murrie, W. P. Diamond, C. M. McCulloch

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over- burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

Predict the cumulative hydrologic impact of mining on the environment. Approach A comprehensive set of computer models has been developed to predict the impact of mining on ground water. Mine inflows, drawdowns in aquifers, and ground water quality can be predicted. How It Works The Prickett-Lonnquist finite-difference groundwater model was specially modified for the hydrologic problems of mining. This model, developed at the Illinois Water Survey in the 1960's,

Jan 1, 1982

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By J. W. Pall

The method of mining bituminous coal in Pennsylvania cannot be treated in an extended manner in this publication since this would require more space than justified. The general plan of operation of most mines is on the room and pillar system, using double entries from which the rooms are driven In the early mining in the Pittsburgh coal bed the "checkerboard" plan was much used, but this entailed a large loss of coal in the blocks of coal that were left standing. In recent years there has been a tendency towards the adoptions of the panel, room and pillar method, also the block system, which ad mats of concentrated mining within a relatively small section of the mine It is not unusual to use 4, 6, or 8 parallel entries for the panel development. The longwall advancing method has been tried in some of the thin beds of the central coal field, but so far it has not passed beyond the experimental stage. The average extraction' of coal throughout the State is 714 per cent, but it is estimated that 15 5 per cent of the loss is avoidable, so the actual extraction should approximate 87 per cent. Pennsylvania is exceptionally well provided with means of transportation by trunk lines, branches, and by intra State railroads, among which are the Pennsylvania, Baltimore & Ohio, New York Central, Buffalo, Rochester & Pittsburgh, Western Maryland, Bessemer & Lake Erie, Pittsburgh & West Virginia, Pittsburgh & Lake Erie, Erie, Monongahela Division, and Montour railroads, all of which reach some of the bituminous mines The Monongahela River furnishes water transportation for Allegheny, Greene, Fayette, and Washington counties During 1923 the coal traffic on this river amounted to 18,709,084 tons, and of coke, 385,426 tons Coal is moved on the Allegheny River also, the total in 1923 being 911,178 tons s.

Jan 1, 1928

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal Workers Pneumoconiosis is the leading cause of death due to occupational illness among coal miners. This disease is caused by miners’ exposure to respirable coal mine dust. A Personal Dust Monitor has recently been developed to provide near real time feedback to miners regarding the number of milligrams of respirable coal mine dust in the air they breathe. This paper was prepared by the National Institute for Occupational Safety and Health to document coal miners’ reactions to this new device, and how they make use of the information it provides. Structured interviews were conducted with 30 coal miners at four mines. A four-stage conceptual model of miners’ decision processes with respect to how they interpret and respond to the dust exposure numbers from their personal dust monitor is proposed. The stages are: Diagnosis, Action Planning and Intervention, Evaluation, and Institutionalization. The interview responses provide considerable support for the model. Most miners paid attention to Personal Dust Monitor feedback and made efforts to reduce their dust exposure. Their efforts included: changing where they positioned themselves, making ventilation system improvements, and using respirators more often. The 29 miners who reported having experience wearing both the old and new type of dust monitors were asked which dust sampling system they preferred. Eighteen (62%) preferred the new monitors, 7 (24%) preferred existing monitors, and 4 (14%) had no preference. The most frequently cited advantage of the new monitor is its ability to provide relatively quick feedback on dust exposure. Miners provided several suggestions for improving the design of the instrument.

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult&apos;s law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

To monitor the quantity and quality of air in underground mines to assure safe working conditions. Approach Several mine air monitoring systems, consisting of sensing stations in the return airways and control stations on the surface, have been Installed and tested. How It Works Sensor stations are located at strategic places in the underground mine. At each station, the sensors measure air velocity, air temperature, methane concentration, and carbon monoxide concentration. In one system, differential air pressure between intake air and return air, is also measured. Output voltages of the sensors are converted to digital signals at the sensor stat ion; these signals are multiplexed so that data from all sensors can be trans-phone wire to a central station. There the data are displayed and alarms are triggered when the sensed values exceed (or in the case of air velocity, fall below) a preset value. In addition to receiving data automatically, the central station can poll individual sensors at any time.

Jan 1, 1978

By P. Yant, A. C. Fieldner

"IntroductionIn its investigations relative to reducing the hazards of carbon monoxide poisoning, the Bureau of Mines recently had its attention drawn to a compound2a sold under a trade name for which claims are reported to have been made regarding its efficacy in reducing that type of poisoning in automobile garages. Accordingly, some of the product was obtained and analyzed for its power to absorb, oxidize, or destroy carbon monoxide; and the results are herein reported.Description of ""Compound"" (quoted from manufacturer's circular)While the circular does not actually state that the ""compound"" protects against carbon monoxide, the inference is therein, because each of the two following quotations is below these respective headings; ""Carbon-Monoxide Poisoning,"" and ""Chronic Gassing Among Garage Workers.""The ""compound"" holds chlorine and oxygen gases in solution with formaldehyde, which unites with the hydrogen to form hydrochloric acid., giving an over-supply of oxygen which burns up carbon just as a piece of wood is burned in the fire. The formaldehyde in the composition of the ""compound"" is a great affinity for ammonia and hydrogen sulphide."

Apr 1, 1924