Search Documents

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are establishes it can be ascertained with a degree of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and. built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town' whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well underdrained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive.Enviroment. The contiguous territory should afford no unwholesome sur¬roundings such as swamps Or accumulations of stagnant water.General Considerations. The water supply to be provided and the method of disposal of wastes influence to a certain extent the location of the camp or town-site. The means of supplying water, whether by gravity or by pupping, and the disposal of sewage, whether by outfall, system, sewage disposal system through septic tanks, broad irrigation or filter beds, or cesspools will govern the location of the site topographically in relation to source of water and point of disposal of sewage.* This article was prepared as part of the paper ""Use and Supply of Water for the Oil-Shale Industry"" by J. J. Jakowsky, to be published by the Department of Metallurgical Research, University of Utah, in cooperation with the United States Bureau of Mines."

Jul 1, 1921

By Joseph V. Mather, E. H. McCleary

"INTRODUCTION Workmen are transported in shafts in various types of cages or skips, most of which were designed primarily for hoisting cars and materials. Therefore, in general the cages or skips are not completely enclosed, adequate and gates are not always provided, and at many mines signaling devices and telephones are re¬stricted to those at the various landings in the shafts.Shaft accidents are usually severe - frequently fatal - and as a rule such an accident is caused by failure to comply with company rules or by ignoring them.Sixty men were killed and 555 men were injured in shafts of the anthracite and bituminous coal mines of the United States during the 5-year period 1938-42. 4/ Many of these accidents could have been prevented by having properly enclosed cages and adequate locking devices on doors to prevent workmen from falling into the shafts.The officials of the Heidelberg Coal Co. contemplated utilizing an old coal-hoisting shaft as a man-hoisting shaft; however, it was their desire to avoid the use of the conventional cage and to try to provide a safer means of transporting men in the shaft. Investigations and studies made by the officials revealed that an elevator similar to those used in large buildings would be more economical in first cost, maintenance, and operating costs would be less, and it would be safer and more convenient for the workmen. Effective safety devices for such elevators have been developed to such a high degree that those properly installed seldom fail. The elevator or man cage finally chosen cannot be pulled above the top landing through mechanical or man failure; it stops automatically at each landing and cannot be moved while a door is open; when the cage leaves the landing the doors opening to the shaft are automatically locked by mechanical and electrically operated locks; electric lights, telephone communication, and push-bottom controls are available on the cage, and adequate safety switches and overspeed controls are provided."

Jun 1, 1947

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By V. F. Parry

Under the present emergency every consumer should store as much coal as he can. Although there is no shortage of coal, there is likely to be a shortage of labor to mine excessive quantities in the fall, and railroads cannot be expected to deliver coal promptly on account of the need for transporting war materials. Some miners must join the armed forces, and those who are left may be unable to mine coal as rapidly as you will need it when winter comes. When the first cold days arrive, there may be a shortage of trucks to deliver coal. Deliveries may be planned in advance, and your turn might not come until it is too late.

Jan 1, 1942

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By L. C. IlsLey

The first thing to consider in prevention of electric shock is the voltage of the circuit. No person can be sure that he will not be killed, even from a 110-volt circuit, if he makes proper contact with the circuit so as to cause the maximum current to pass through his body. As the voltage is increased to 250 volts, 500 volts, or 2,300 volts the danger from contact with the electric circuit is increased, Alternating current of the same nominal voltage is possibly more dangerous than direct current. Experience has taught us that both will cause death, and that if the fatalities from this source are to be kept low, certain precautions in the guarding of circuits must be observed.

Feb 1, 1929

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By R. Hogg, T. F. Dumm

"It is generally agreed that dust characteristics play a role in the development of Coal Workers' Pneumoconiosis (CWP). Unfortunately, there is a serious lack of information on what the characteristics of mine dust actually are and how they vary among different mining regions, coal seams, etc. This paucity of data can generally be attributed to the serious problems encountered in collecting sufficiently large quantities of dust for conventional analytical procedures.Personal samplers are widely used in coal mines for regulatory and enforcement purposes. Generally, these provide information only on the total (respirable) dust loading in the mine atmosphere and on the mineral matter (primarily quartz) content of the respirable dust. A procedure has been developed by which samples collected with a slightly modified personal sampler can be analyzed for particle size distribution, total mineral matter content and elemental composition, in addition to the standard mass and quartz measurements. These analyses could readily be performed on a routine basis. Shape analysis by Scanning Electron Microscope (SEM) could easily be included if appropriate shape criteria are established. Extension of the procedure to include the determination of complete size/specific gravity (composition) distributions is quite straightforward provided sufficiently large samples (at least 10 mg) can be collected. Typical sample sizes for a personal sampler carried by a miner for one shift range from about 0.5 to 2 mg.The basic procedure was developed and evaluated using synthetic mine dust prepared in the laboratory. Field tests in three working mines in Pennsylvania and West Virginia have confirmed the applicability of the approach to the real world. Particle size distribution measurements on mine dust collected in the modified personal sampler were found to agree closely with the results of simultaneous in situ measurements obtained using cascade impactors."

Mar 1, 1989

By F. W. Hoertel

Near-optimum parameters were determined by the Bureau of Mines for vapor deposition of rhenium on heated copper substrates by hydrogen reduction of rhenium hexafluoride (ReF6). High-purity deposits of nearly 90-percent theo¬retical density were obtained with the reaction chamber at 250° C, with an H2 to ReF6 volume ratio of 25 to 1, and with an ReF6 flow rate of 5 grams per hour. Some rhenium deposited as a loose, black powder. When the established near-optimum parameters were carefully followed, this could be minimized but never completely avoided. Varying the reaction chamber pressure, both above and below atmospheric, yielded excessive quantities of rhenium powder. Deposition efficiencies, based on only the coherent metal, ranged between 70 and 75 percent. Massive deposits contained only spectrographic traces of impurities. The average microhardness (Knoop, 100-gram load) of vapor-deposited rhenium was 907. Limited research on the deposition of rhenium-tungsten alloys by reduction of the mixed hexafluorides produced deposits in which linear composition gradients were pronounced; this nonhomogeneity was attributed to the wide variation in optimum hydrogen-reduction temperatures of the two hexafluorides (250° C for ReF6 and 550° C for WF6). Using deposition temperatures between 250° and 550° C did not eliminate the composition variations.

Jan 1, 1967

By W. Wan, R. V. Ramani, J. M. Mutmansky

"Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer, and distribution of DPM in coal mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Analyzed using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study is presented.With diesel equipment holding an important place in underground coal mining and growing in use over time, it is important to develop and improve controls of the exhaust emissions, especially diesel particulate matter (DPM), to further reduce potential health hazards. The proper design and maintenance of diesel engines and on¬board control procedures are paramount requirements for controlling DPM successfully. There is also, however, a significant reduction potential in terms of personal exposure that can be realized by managing the DPM that gets into the airstream. Strategic design of the mining, ventilation, and equipment implementation systems remain essential for efficiently reducing the DPM concentrations.Modeling the effect of diesel exhaust contaminants upon the mine atmospheric quality will permit improved health and safety design of the overall mining and ventilation systems. Numerous studies have been performed to model the distribution/transport of gaseous and particulate emissions in the underground mine atmosphere and some very sophisticated convection/diffusion models have been developed (Skobunov, 1974; Thakur, 1974; Stefanko and Ramani, 1975; Wala, 1980; Bandopadhyay and Ramani, 1983). Most of these models were developed for a single airway or based on the assumption that the ventilation network of a mining section can be approximately represented by a single intake and a single return. The complexity of most models of the convection/diffusion type and the mobility aspect of diesel haulage units made a detailed emissions model very difficult to develop.The current model is an attempt to fill the need for a more generic tool applicable to mining sections employing multiple mobile diesel units by simplifying the convection-diffusion model to a convection-only model. The simplification is based on the fact that the diffusion coefficient will affect only the transient environmental contaminant concentrations with little or no affect on the time-weighted-average concentrations over a relatively long period such as a working shift (Lee et al., 1994). In view of the difficulties involved in mathematical modeling, the approach here is developing and using a computer simulation model. A PC-based FORTRAN 77 simulation model for the analysis of mining systems with multiple diesel sources and any ventilation network configuration was developed to study the distribution/transport of DPM in mine airways, evaluate methods of reducing DPM concentrations, and explore modifications to existing mining practice."

Dec 1, 1996

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX D DEVELOPMENT AND EXPERIMENTAL VERIFICATION OF ACOUSTIC SEAL CHECKER THEORY 1. Introduction In Section 7 of the report the acoustic seal checker concept was described in a general manner and the parameters which affect the signal level at the microphone were discussed briefly. In this appendix the theoretical basis will be presented and the experimental program described which permitted the extension of the theory into practice. The basic goal of the acoustic seal checker is to relate the reduction in sound pressure level to the size of the residual hole in the fly ash barrier. The smallest hole size that may be measured is determined by the signal to noise ratio, where the noise in this case includes the ambient noise in the mine, the internal microphone noise and the sound transmitted from the acoustic source via the flanking paths through corridors adjacent to the one being sealed. The latter source of noise can be discriminated against, at the expense of increased complexity of the acoustic system, by employing a pulsed source and pulse gating of the microphone signal set to accept sound via the barrier path and to reject the delayed flanking path signals. In order that the acoustic system be insensitive to precise source and microphone location and to permit assessment of system performance on an acoustic power flow basis, a broad frequency band of pseudo-random noise is emitted by the loudspeaker source. The preferred frequency range must be determined, the advantage of a directive source must be assessed, and the necessity

Jan 1, 1973

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. E. Murphy

The Bureau of Mines developed a hydrometallurgical method for recovering mercury metal from mercury sulfide concentrates. Sulfide flotation concentrate from the McDermitt Mine was leached in a cupric chloride solution at 80° C. The redox potential of the solution was maintained at 850 mV during leaching by chlorine sparging. Mercury extractions exceeded 99 pct in 3 h of leaching. After leaching, the pH of the solu-tion was increased from 1 to 4.5 to precipitate copper as atacamite. The pregnant solution typically containing 100 giL Hg was sent to elec-trolysis to produce high-purity mercury metal and chlorine for recycle. In a 200-A electrolytic cell operated for 24 h, current efficiency was 99 pct and the energy requirement was 0.9 kW·h/lb of mercury produced. Mercury removal from the waste stream was also investigated. Iron or zinc cementation, sulfide precipitation with H2S, and activated carbon adsorption all decreased the mercury concentration from 10 giL to 0.01 mglL, which is less than the Environmental Protection Agency limit on wastewater of 0.02 mg/L.

Jan 1, 1987