Search Documents

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

By Larry P. Jackson

As part of the current research effort in shale-oil chemistry conducted by the Federal Bureau of Mines, reduced chlorophyllins were prepared and pyrolyzed in an effort to identify the role of plant pigments and their decomposition products in the nitrogenous compounds found in the product of oil-shale pyrolysis. The properties of the chlorophyllin pyrolysates were related to the composition of the reduced chlorophyllins with particular emphasis on the amount and types of nitrogen compounds formed. A comparison based on the types of nitrogen compounds present was made betvJeen shale oil and the chlorophyll in pyrolsates. In order to make this comparison, a sample of shale-oil light distillate was separated into polar and nonpolar fractions, and a careful examination of the polar fraction was conducted to obtain an accurate picture of the types of nitrogen compounds present. The information gathered from these studies was used to evaluate reduced chlorophyllin as a model of oil-shale kerogen insofar as the production of nitrogen compounds was concerned. The results indicate that the reduced chlorophyllin does yield nitrogen products which are directly related to the nitrogenous compounds in shale oil, and it therefore represents a good model of shale-oil kerogen.

Jan 1, 1975

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Ted C. Briggs

Equations for the elastic pressure distortion of the volumes of a Burnett compressibility apparatus are developed and presented in this report for volumes under internal and external applied pressures. An experimental method for the determination of the external pressure distortion coefficients is presented. Young?s modulus and the internal-pressure distortion coefficients are computed from the experimentally determined external-pressure distortion coefficients. The temperature dependence of the pressure distortion coefficients and of Young's modulus is evaluated for the temperature range 0° to 80° C.

Jan 1, 1968

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By Stephen C. Tadolini, Thomas M. Barczak

Western mines have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the early 1990’s provided a very effective alternative and remains the dominant form of tailgate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled together, provides more capacity than an equivalent sized Can support and improves transport efficiency. However, the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but they have not been proven in high deformation environments. Alternative supports are also being used in longwall recovery operations. These include the Rocprop and Omni Prop, which are extendable support systems. They also provide active roof loading which can be beneficial in these applications. Specialty supports, such as the Sand Prop and Spider Prop, have also been introduced into western longwall operations. This paper compares the performance characteristics of these various support systems.

By D. Harrington

Research in connection with occupational diseases, including silicosis or, more definitely, pneumoconiosis, has been prosecuted much more actively in North American countries during the past 5 or 10 years than in any other known period. This applies particularly to the United States, owing largely to the fact that in recent years compensation for ill health presumed to be caused by industrial work of certain kinds is being paid to a far greater extent in this country than previously. Most other countries have had occupational-disease laws for many years. Court rulings in the United States, which started 5 or 6 years ago, have given a few heavy verdicts in connection with ill health or death caused, or alleged to have been caused, by some phase of occupational work other than traumatic injury, and these have called attention to the fact that ill health and even incapacitation can be caused by some kinds of employment. With the onset of the world-wide financial depression, which resulted in permanent abandonment of many business or industrial enterprises (among them mines) in the United States, the workers frequently believed that they could expect nothing in the future from their former employers, hence they felt free to demand monetary benefits or damages because of ill health which they suffered, or thought they suffered, because of their previous employment. The result was a flood of lawsuits and. compensation claims for occupational disease, particularly where dust was involved.

Jan 1, 1938

By E. O. Bennett

Various methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of tests show that the "shut-in pressure-drop" method described by Rawlins2 is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rate of leakage from the fall in pressure and change in temperature determined by the "shut-in pressure-drop" method of testing. METHOD OF MEASURING PRESSURE DROP The gas is "shut in" the line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The change in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.

Jan 1, 1926

By Philip B. Lorenz

A Bureau of Mines feasibility study on the use of tracer pulses to assess the degree of fracturing in an underground formation consisted of three phases: 1. A laboratory study on sand packs and open tubes, which developed a correlation between dispersion of the pulse and size of the flow channels. 2. A test on a retort, 11 feet in diameter and 45 feet high, packed with shale rubble. Void volume was measured, but evaluation of channel size was not possible because of interference from the space unoccupied by the matrix. 3. A field test on an explosively fractured shale formation. Pressure, flow, and transit time led to qualitative estimates of fracture pattern, but quantitative detection of dispersion in the formation was overwhelmed by dispersion effects in the well.

Jan 1, 1973

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973

By Wilbur I. Duvall

This report presents experimental data on the propagation of explosion- generated strain pulses in rock. Tests were performed in 5 different rock types, employing 10 different types of explosives. Charge sizes ranged from 0.5 to 50 pounds, and travel distances ranged from 2.5 to 70 feet. Analysis of the data shows that the experimental peak strain data satisfy an exponential decay propagation law of the form: ?R/W1/3 = Ke ?aR/W1/3. For a particular rock, parameter K is a linear function of the calculated detonation pressure or the calculated energy density of the explosive. For a particular explosive, K is a linear function of the elastic parameter of the rock, p2, a result, which is at variance with elastic theory. The absorption constant, a, is independent of type of explosive but dependent upon rock type. However, no definite relation between a and the physical properties of the rock could be established.

Jan 1, 1959

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By R. S. Olsen

The Bureau of Mines is engaged in a continuing research effort toward the recovery of alumina from kaolinitic clay and other nonbauxitic domestic minerals. Hydrochloric acid extraction of calcined clay is among the acid processes under consideration. Although aluminum is easily leached from calcined clay, the presence of fines and slimes in the leached residue has hindered the application of this and other acid leaching processes. A clay feed preparation method was therefore developed that eliminated the slimy nature and the separation problems normally associated with leached clay residues. The preparation process consists of crushing the raw clay to minus 20 mesh, dampening the crushed clay with a fine water mist while tumbling on a rotating disk, and calcining the misted clay at 750° C. The misting process increases residue settling rates threefold to 9 cm/min (18 ft/hr) and filtration rates by two orders of magnitude. Leaching-kinetics were determined for misted clay feeds in a batch, stirred-tank reactor. Rapid leaching occurred during the first 85 to 90 pct of the extraction. The linear relationship of extraction to time during this initial phase corresponded to a zero order reaction with a rate constant of around 10 pct/min.

Jan 1, 1981

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By R. E. Perry

In connection with a program of coal research at the Southern Experiment Station the Bureau of Mines, in cooperation with the University of Alabama and the various coal operators, conducts washability studies of coal from beds in Alabama and other Southern States in which commercially important deposits occur. One of the main objectives of a washability study is to obtain technically and commercially important data necessary for determining the best methods for preparing and utilizing the Nation's limited reserves of coking coal. Such information is important to conservation because it facilitates selection of preparation methods that will provide maximum yields of coal with low ash and sulfur contents.

Jan 1, 1958