Search Documents

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

By R. Van A. Mills

[In previous contributions** the writer has called attention to important relations that faulting bears to the migration and accumulation of oil end gas. It has been pointed that favorably situated parts of oil and gas bearing, sands have been enriched by migration art segregation incident to faulting. The escape of water through natural passages such. as fault fissures has induced wide spread hydraulic currents through the beds toward these, points, of diminished pressure and these water currents, plus buoyancy hove contributed largely toward the migration of oil to favorable rock entrapments in the vicinity of the faults.*** The propulsive force of expanding gas has been one of the contributing causes for the hydraulic currents. Paradoxical as it may seem, the escape of gas with entrained oil through fissures has been on important factor In the migration, and accumulation of oil in many faulted areas. Compressed gas is the propulsive force by which oil generally moves to producing wells. It is also one of the propulsive forces by which oil has moved with or even ahead of water under conditions: of differential pressure brought about by faulting.]

Jan 1, 1922

By Guy A. Johnson

This Bureau of Mines report summarizes the results of efforts to develop reasonably priced, reliable mine shaft fire and smoke protection hardware for metal and nonmetal mines. The hardware was incorporated into a viable prototype system that would minimize fire and smoke hazards. The design of the system had to be sufficiently flexible to be utilized in a wide variety of metal and nonmetal mine shaft and shaft station configurations. As a result of long-term, rugged field tests, an improved (second generation) system was developed. The hardware is now commercially available.

Jan 1, 1978

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

By Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

Problem: Incident investigation reports do not usually contain enough information to aid in studying boom arm vertical speed for roof bolting machines to determine the impact that appendage speed had on an operator's risk of experiencing a contact. Laboratory experiments with human subjects are also not feasible because of safety and ethical issues. Method Researchers successfully developed a three-dimensional computer model that uses virtual human simulation software as the primary means to gather contact data when the boom arm touches the operator's hand, arm, head, or leg. Results: Data analysis of roof bolter simulations shows that the speed of the boom arm is the most important factor in determining the risk of an operator making contact. Regardless of other variables, contact incidents were always greater when the bolter arm was moving up, greater on the hand, and greater for the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom arm is ascending. Based on the data collected, boom speeds greater than 13 in/sec result in a substantial increase in risk to the roof bolter operator of making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Impact on Industry: The use of such information can be quite helpful in making recommendations to machine design and task procedures to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By Stephen C. Brown

THE expansion of the world economy which has been in process since 1958 continued in 1963 and both production and consumption of minerals rose. Gross national product (GNP) rose sharply in the United Kingdom and Japan, continued to expand in the United States and Canada, and maintained a high though slightly declining rate of growth in the European Economic Community (EEC) despite the appearance of excess capacity in certain lines and inflationary pressures in Italy and France. The steel and motor vehicle industries both increased output in North America, Western Europe, and Japan. The less developed areas benefited substantially from an improvement in their terms of trade, and their export earnings increased some 8 percent in 1963; although estimates of GNP for the majority of them are 110t yet available, it is probable that this increase was partly reflected in a substantial rise of GNP.2 In the United States the expansion was steady and extended through all sectors of the economy producing no distortions likely to disturb its continuing growth; at yearend with unemployment still at about 5.5 percent of the labor force and operating rates of industry estimated at about 87 percent of capacity, there was a substantial margin for further expansion. Though the balance of payments was still in heavy deficit for the year, in the last half it was moving rapidly toward equalibrium as net exports rose and capital outflows declined; prices were relatively stable, inventories increased only slightly and the activity of mineral-consuming industries remained high, steel output rising by 11 percent to highest level since 1957 and the auto industry output equalling the 1955 record.3

Jan 1, 1964

By W. A. Cole

This report covers the preliminary phase of an investigation of clays, shales, and certain rocks in Wisconsin to determine the feasibility of processing lightweight aggregate in the State. The study was extended to include rotary-kiln testing of a limited number of shale samples, and to an appraisal of the Maquoketa shale resources in eastern Wisconsin. A total of 45 samples of clays, shales, and other argillaceous rocks of Wisconsin were tested. The lower Maquoketa shale is the only material found to date that offers possibilities as a source of material that can be processed in a rotary kiln for lightweight aggregate. Bedrock occurrences of the Maquoketa shale are found in the eastern and southwestern parts of the State. The populous southeastern region of Wisconsin presents a large potential marketing area for lightweight aggregate. For this reason special study was directed to the Maquoketa shale in the eastern district.

Jan 1, 1961

By E. J. Kloos

The Bureau of Mines devised a new machine-test method for measuring carbon dioxide inspired by a wearer of self-contained breathing apparatus. The new method compares favorably in speed and precision with standard man-tests in which the apparatus is tested while actually worn, and is scheduled for use in future approval tests for facepiece carbon dioxide 'measurements. However, man-tests will still be used to measure the efficiency of the carbon dioxide sorbent materials in closed-circuit breathing apparatus.

Jan 1, 1966

By Philip W. Holland

The Bureau of Mines has developed a trace helium analyzer for deter-mining helium-4 in the parts-per-billion range. The instrument is used for analyzing pure gases, laboratory-prepared standards, and atmospher-ic samples. Accuracy at the 95-pct confidence level in the 50-to 20,000-ppb range is within ±2 ppb or ±0.4 pct, whichever is greater. The minimum detectable helium-4 concentration is calculated to be 5 ppb. The analyzer consists of a modified helium leak-detector mass spec-trometer, a laboratory-built sample inlet system, and a liquid-nitrogen-cooled charcoal trap. A programmable integrator and event-control module make automatic operation possible. The portability of the analyzer allows it to be used in the field.

Jan 1, 1984

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By John P. Gooch

The Bureau of Mines wrote a computer program which calculates the saturation curves and condensation characteristics of gaseous mixtures consisting of binary organic vapor and air. The program employs an algorithm which assumes an equilibrium mechanism for condensation, and the degree of fractionation obtained is predicted on the basis of relative volatility. The program incorporates a feature which allows the user to examine the fractionation resulting from condensation as a function of the size of the temperature increments over which condensation is assumed to occur. If a single. temperature interval between the dewpoint of the mixture and the outlet temperature of the condenser is assumed for the calculation, the results obtained will be those resulting from a single equilibrium condensation. If the condensation is assumed to occur over a number of temperature increments, the results obtained will approach those predicted by the Rayleigh equation as the magnitude of the temperature increments approaches zero. The results from calculations performed on vapor mixtures from organic heavy liquid solutions used in beneficiating potash and brucite ores are presented. The liquids are solutions of dibromomethane in trichloroethylene or perchloroethylene. The results show the degree of liquid recovery which is possible by cooling mixtures of organic vapor in air. Compositions of the vapor range from 10 to 95 percent air, and assumed condenser exit temperatures range from 110° to 50° F.

Jan 1, 1971

By Robert D. Schmidt

This Bureau of Mines report describes the development and application of a computer model for simulating the hydrological activity associated with in situ leaching. The model is intended to provide uranium resource developers with a description of the flow behavior of leachants and ground water during the development, production, and restoration phases of a leaching operation involving an arbitrary pattern of injection and recovery wells. Different aquifer environments are modeled, using a closed-form solution to the partial differential equation that describes three-dimensional changes in piezometric head as a result of pumping from leachant injection and recovery wells. The computer program can model a maximum of, 50 arbitarily located wells. Numerical techniques involving difference quotients and Taylor expansions about time points are used to derive time, velocity, areal sweep, and fluid volume parameters associated with leaching hydraulics. These parameters are output by the program in graphic and tabular formats. Other numeric methods insure that the program running time is minimized without significantly affect-ing the accuracy of results.

Jan 1, 1980