Search Documents

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959

By E. L. Garton

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 3134, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and January and March, 1932, as published in Reports of Investigations 3140, 3147, 3150, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active Permissible list: Austin Red Diamond No. 1, L. F. Gel-Coalite W, L. F;" Austin Red Diamond No: 5. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.

Jan 1, 1932

By D. Harrington

An explosive may be defined as a substance (usually a mixture) that has the property of yielding, readily to combustion or oxidation upon application of flame or shock, the combustion or oxidation process being rapid and accompanied by formation of such relatively large quantities of gases that much violence and pressure are produced; these, in turn, react against their surroundings and cause what is termed an explosion. By their very nature their action is destructive and disruptive of adjunct materials; hence, all explosives axe potentially hazardous and every type of explosive, irrespective of its relative safety, should be handled, .stored, and used with utmost care at all times and under all conditions. It should always be remembered that any explosive can be rude safe only in certain of its features and under certain conditions and circumstance. If these facts (and they certainly are facts) are always kept in mind, most of the modern types of explosives can be utilized advantageously in our industrial life and with a considerable degree of safety. That commercial explosives can be handled. safely is borne out in part by the fact that in the past 15 years at least 3,000,000,000 pounds of the commercial explosive dynamite have been transported by railroads in the United State, without injury to any person, insofar as available records indicate.

Jan 1, 1939

By M. M. Jones

Natural brines are potential domestic resources of minerals. The brines of Searles Lake, CA, for example, contain an estimated one-fourth of our current reserve of tungsten. A key to Bureau of Mines research to recover this critical mineral is the ability to quantitatively measure concentrations of particular constituents in the large number of brine samples and process solutions produced under a multiplicity of test conditions. This paper describes procedures used to determine arsenic, boron, phosphorus, silicon, and tungsten in these solutions by simultaneous inductively coupled plasma spectrometry. A variable in-ternal standard method was used to compensate for tungsten interference on the other analytes in tungsten concentrates, and matching standards were used to determine tungsten in raw brine. Other solutions were analyzed using normal techniques. Analytes were determined down to 1 mg/L with an average precision of 2.5 pet relative standard deviation. Accuracy, estimated using synthetic solutions and by comparison with values obtained by other methods, averaged about 2.5 pet. The methods were rapid, required little sample preparation, and provided the needed sensitivity.

Jan 1, 1985

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By E. W. Pehrson

In making any canvass of secondary metals great care must be exercised to avoid duplication or exaggeration of net consumption. One of the major difficulties is to trace the metal accurately as it passes through the many cycles of manufacture. Greater or less duplication probably occurs in any canvass. The manufacturer of tin plate, for instance, purchases primary pig tin exclusively as a raw material. Most of it goes into the coating on the steel sheet, but a substantial part emerges in the form of byproducts such as scruffs and drosses. These are sold to other plants, where they are used in the manufacture of alloys and chemicals. Alloys and chemicals, however, are not necessarily articles for final consumption. The alloy may be sold in ingot form to a bearing manufacturer, who, in turn may produce some scrap, which he may sell to still' another plant that may make still other products. There is a considerable return of tin in the form of waste products from chemicals sold to the silk industry. Even tin plate does not represent an ultimate use of tin because the tin-can maker produces large amounts of clippings, which are sold to detinning plants, where the tin is recovered and used again for some other purpose. Thus the degree of duplication in consumption statistics depends on the point in the industrial cycle where consumption is measured.

Jan 1, 1936

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By L. R. Willmott

An ethanolamine purification unit for removing carbon dioxide and hydrogen sulfide from Firscher-Tropsch synthesis gas was installed at the Bureau of Mines synthetic liquid fuels demonstration plant at Louisiana, Mo. The unit was a surplus Radford Girbotol unit from the Missouri Ordnance Works modified for a capacity of 90,000 std. cu. ft per hour of synthesis gas at 450 p.s.i.g., operating pressure. The hydrogen sulfide loading of the feed gas was specified at 500 grains per 100 cu. Ft. The unit was designed by the Girdler Corp. and installed by the Koppers Co. Initial operations were conducted far 11 days in May 1951. Thereafter 7 additional runs were made, varying lo duration from 8 to 54 days. The last run was terminated on May 29, 1953, the total time the Plant wars in operation being 219 days.

Jan 1, 1956

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930