Search Documents

By R. B. Schluter

The objective of this Bureau of Mines investigation was to determine the effects of adding manganese compounds and ores to iron ore pellets. Manganese dioxide, carbonate, sulfate and chloride, plus six manganiferous ores from the Minnesota Cuyuna Range were tested as additives to increase the manganese content of iron ore pellets. One to 5 percent manganese, as a compound or ore, was added to five magnetite concentrates and one hematite concentrate. These concentrates were ballad, indurated (1,300° C), and tested for reducibility. Manganese sulfate and chloride were unsatisfactory additives causing cracking and degradation of the pellets during reduction. Manganese dioxide, carbonate, and the ores were satisfactory additives. The additives increased pellet compression strengths with a corresponding loss of reducibility, as compared to the pellets without manganese additions. The changes in compression strengths and reducibility were caused by the formation of Jacobite spinel and slag within the pellets. However, when the induration temperature was lowered from 1,300° to 1,200° C the reducibility and compression strengths were comparable to the pellets without manganese additions indurated at 1,300° C.

Jan 1, 1974

By W. C. Sanborn

The Bureau of Mines program of investigation and development of domestic mineral deposits had as its wartime objective the most effective immediate utilization of these resources in the interest of National security. Since the war, the results of individual projects are being prepared for publication as rapidly as practicable. Numerous chromite deposits were examined, among them those of the French Hill Mine in northern California. Situated 16 miles east of Crescent City, 76 miles from the nearest railroad shipping point at Grants Pass, Oreg., this deposit had a recorded yield of about l4,000 tons of metallurgical-grade chromite to the end of 1943. By the end of 1946, total production was more than 25,000 tons, averaging 43 percent Cr2O3, with a chrome:iron ratio of about 2.5:1.

Jan 1, 1948

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By A. J. Kraemer

"During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attack bearings, wrist pins, and other parts of engines. On the other hand, in making gasoline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more than 90 per cent of the 153 samples analyzed passed the Federal specification requirement, Which limits the sulphur content to 0.10 per cent. 3This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity ad distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995."

Jun 1, 1930

By Robert W. Freedman

The Bureau of Mines investigated methods of analysis of free silica in respirable dust, including both work done at the Bureau of Mines and work done elsewhere. The review covers both coal dust and noncoal dust, taking into account both existing and proposed chemical and spectroscopic procedures.

Jan 1, 1971

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By I. AITKENS

The opal , long in disfavor because it was considered " unlucky, " has become much more popular in recent years . For variety and beauty of color the precious opal is without a peer . These colors do not come from any chemical constituent but are produced by structural peculiarities , which in varying degrees deflect the light rays entering the stone and give a prismatic play of hues .

Sep 1, 1931

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By S. R. Borrowman

Mill tailings from conventional uranium extraction processes contain nearly all of the radium originally in the ore. Such tailings require controlled storage in perpetuity to safeguard the surrounding environment from radioactive contamination. Alternatives to controlled storage of the tailings are (1) removal of the radium from the tailings for separate storage or use or (2) removal of the radium when processing the uranium ore. In laboratory tests conducted by the Federal Bureau of Mines, radium was leached from tailings using either hydrochloric acid or ethylenediamine tetraacetic acid. A hydrochloric acid leaching method was used to extract both radium and uranium from the ore to yield tailings containing less radium than those produced by either conventional sulfuric acid or alkaline leaching processes. From 77 to 94 percent of the radium in mill tailings was concentrated by sedimentation in slime fractions representing nearly 25 weight-percent of the original sample.

Jan 1, 1975

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By Robert Howard

With the rapid depletion of the Peerless Coal Co.'s mine in Spring Canyon, it was necessary, if the company was to remain in the coal-producing business, to look to the development of a new property or to acquire a mine already developed. After careful investigation of several operating properties it was decided by the officials of the company to take over the lease on an undeveloped acreage held by a private party in Price Canyon, about 3 miles north of Castle Gate, Utah.

Jan 1, 1930

By A. W. Khair, M. Ahmad, L. D. Gehl

"This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a more dusty environment.IntroductionThe high demand for coal production has increased the need for mechanized coal cutting in underground coal mines. Continuous miners have been used in the United States of America for nearly four decades and now presently more than 2000 are in operation. Almost half of the underground coal production of the country is by continuous miners. Today, competition in the coal industry has increased, due mainly to market conditions and legal restrictions, thus placing an emphasis on production, efficiency, and safety. The use of continuous miners has resulted in the generation of respirable coal dust which causes black lung in mine workers. On the other hand, bit wear presents a serious problem as it affects productivity and economy.Much research in the put has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in the cutting process. Recently, dust hazards in underground coal mines as a result of coal cutting has been a great concern to mining engineers as well as environmentalist of the country. In past, much emphasize has been given to fragmentation mechanics (Khair et al, 1989), dust generation due to regrinding (Khair and Xu, 1991) and dust generation due to bit wear (Khair, Xu. and Ahmad, 1992). These studies concluded that dust concentration increased considerably after a bit weight loss of 7% and thereafter the bit should be replaced. Thus, legal restriction by the Mine Health and Safety Administration for the respirable dust concentration in underground might be a factor deciding the level or rate of production using continuous miners. While efforts in research are on reducing dust generation, it is also important and relevant to study bit wear in more detail.Bit wear is affected by three major groups of parameters: (1) machine operating parameters, (2) insitu conditions and (3) properties of rock. Again, past studies have shown that depth of cut, material of tool, position of water jet and velocity of the rotating drum are very important machine operating parameters. The content of the rock/coal material is important as bit wear is usually due to abrasion or adhesion. Diffusive wear becomes dominant only when the temperature exceeds the sensitive range i.e critical temperature. Mechanical tools have indicated that a rise in temperature is a function of drum velocity, properties of cutting material (rock or coal) and properties of tool. Bit wear due to chemical reaction and oxidation art almost negligible in coal cutting."

Nov 1, 1995

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965