Search Documents

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By R. K. Franklin, S. T. Reese, J. J. Forbes

"INTRODUCTION It is a recognized fact that in the coal-mining industry coal dust must be allayed to promote the safety and health of underground workers. The Bureau of Mines has been cognizant of the hazards of coal dust for many years, and the necessity of controlling such dust was acknowledged when the Federal Mine Safety Code was formulated. Accumulations of coal dust increase the explosion hazard in a bituminous-coal mine and facilitate the propagation of an explosion. Some of the coal dust produced in mining is inhaled by the workers and contributes to respiratory infection. Impairment of vision and personal discomfort resulting from working in dense clouds of coal dust reflect unfavorably on the efficiency of workmen. Considerable coal dust, originating at the working face, is carried in the ventilating current and deposited elsewhere in the mine, thereby increasing the explosion hazard. It is apparent, therefore, that if coal dust could be allayed effectively at its points of origin, the dust-explosion hazard in bituminous-coal mines would be reduced greatly.Although dust control is practiced in many bituminous-coal and lignite mines, the extent and effectiveness of control for the, entire industry-is not generally known. The purpose of this circular is to present such information clearly, and to encourage coal-mine operators to install dust- allaying equipment.Factual data on dust-allaying practices at working faces in a large number of the bituminous-coal and lignite mines in the United States were .compiled from reports on recent Federal inspections of these mines, The information is presented in tabular form to permit review of the dust-allaying practices of a substantial part of the industry, by States, and also according to employment, and loading practice."

May 1, 1950

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By C. C. Anderson, H. H. Hinson, H. J. Snhroeder

"INTRODUCTION The Eunice field is one of a group in southeastern New Mexico producing oil and gas from so-called limestone-type reservoirs in which the productive strata are dolomite or dolomitic limestone ordinarily, wells in reservoirs of this type show wide differences in their productive characteristics, indicating erratic variations in porosity and permeability. Often there is a large difference in total footage of actual ""pay"" penetrated in neighboring wells and the vertical distribution of the ""pay"" within the productive strata varies. In the Eunice field there are few easily recognizable geologic markers to indicate true structural conditions of the oil-productive section, due to horizontal and vertical gradation in chemical compositions and lithologic characteristics of the strata. Geologic markers are found some distance above the oil-producing zones in this field and consequently they indicate only the general structure. Furthermore, no direct relation has been found between the general structure and the accumulation of oil within the reservoir.Many problems in well-completion and production practice have been met in the Eunice field because of erratic variations in porosity, permeability, in vertical distribution of ""pays,"" and the apparent departure from ordinarily accepted relations of oil accumulation to structure. A detailed study of the position and characteristics of the oil- and gas-producing zones aids production procedure. The methods employed in studying the Eunice field, discussed in this paper, may be applicable to other limestone-type reservoirs."

Jul 1, 1939

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems in developing urban areas. Uncertain knowledge of abandoned coal mines also imposes potential hazards in coal excavation operations since water inundation or the release of methane gas is a pricnipal hazard when mine excavation operations break into an abandoned mine. U.S. Army requirements for an effective method for detecting and mapping subversive man-made tunnels have resulted in a surface-operated automatic earth resistivity survey system with a digital computer data processing system. Field tests aimed at demonstrating the system performance resulted in successful detection of tunnels having depth-to-diameter ratios up to 15 to 1. Under the sponsorship of the Bureau of Mines, a similar system was designed and constructed for use in the detection of coal mine workings. This report discusses the hardware and software aspects of the system and the application of the high-resolution earth resistivity method to the survey and mapping of abandoned coal mine workings. In the field tests reported, the targets of interest were both air-filled and water-filled workings.

Jan 1, 1980

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By R. H. Nafziger

The Bureau of Mines evaluated 18 domestic titaniferous materials with widely varying compositions, mineralogy, and physical properties in electric-arc furnaces, Techniques were devised to recover both the titanium and iron values contained in these materials so that the reliance of the United States on foreign sources of higher grade ilmenites and rutile might be decreased. Most of the tested titaniferous materials responded well to lower grade or byproduct reductants, such as bituminous coals, charcoal, and coke breeze. Sufficient slag fluidity was realized by maintaining from 8 to 12 wt-pct iron in the slags; no contaminating fluidizers were required. Fluid slags containing up to 79, 70, and 54 wt-pct Ti02 were realized from east coast ilmenites, a rock ilmenite, and a titaniferous magnetite ore, respectively. A carbon-lined furnace shell is recommended for minimum slag contamination. Good results also were obtained during extended submerged-arc furnace tests.

Jan 1, 1980

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By R. S. Fowkes

Jetstream pressure distributions and coal cutting rates were determined for a number of nozzles and under different operating conditions. The jetstrearn pressure distribution data were fitted to an assumed curvilinear equation by the utilization of a numerical least-squares technique with the aid of a digital computer. Subsequent manipulation of the approximation equation showed that the total force of the jetstream, rather than its maximum pressure or total kinetic energy per unit Lime, was the most significant quantity affecting the coal cutting rate. A shorter method for assessing the ability of a nozzle to cut coal was found.

Jan 1, 1968

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

The Florida phosphate industry, which supplies about three-quarters of the domestic phosphate fertilizer, produces tremendous volumes of phosphatic clay wastes (slimes). These clays retain a high percentage of water for extended periods of time. The clays also pose an environmental hazard because the disposal technique involves aboveground storage behind earthen dams. Although much research has been undertaken by numerous organizations to dewater slime, no completely satisfactory solution has been developed. In June 1972, a cooperative effort by the Federal Bureau of Mines and the Florida phosphate mining industry was initiated to develop a solution for dewatering the Florida phosphatic slimes. This report discusses various aspects of the slimes problem, reviews past research, makes recommendations for future research, and includes a bibliography of references and patents dealing with the subject.

Jan 1, 1975

By M. J. Kovalik, D. E. Wolfson, F. Fischler

Plastometric tests were made to determine the maximum thickness of the plastic layer for different U.S. coals . The effect of test variables on the maximum thickness of the plastic layer was studied . The values for the maximum thickness of the plastic layer were found to be related to the Gieseler maximum fluidity , plastic temperature range , free swelling index , and other plastic properties of coals . Only a general relationship was observed between the plastometric parameters obtained in these tests and the coking properties of coal .

Jan 1, 1964

By P. G. Clites

This bulletin summarizes the results of Bureau of Mines research on the development of the inductoslag melting process. Inductoslag melting is an induction melting technique using a segmented, water-cooled, copper crucible. The process was developed as part of the Bureau's work on effective utilization of reactive metal scrap, and the process has been applied to melting Ti, Zr, Cr, Co, Fe, Ni, and V. Construction details are given for the segmented crucibles and for both an ingot furnace and a casting furnace. The melting process is described, and results of tests conducted with a variety of reactive metals are given.

Jan 1, 1982