Search Documents

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By R. J. Leary

Significant improvements in surface conditions or mechanical properties of steels have been attributed by several investigators to ladle additions of small quantities of rare-earth metals or their oxides. To investigate systematically these effects in wrought and in cast plain carbon and alloy mechanical steels containing approximately 0.35 percent carbon, heats of four representative compositions were melted by the Bureau of Mines in a 4-ton open-hearth furnace. Each heat was cast into three sets of ingots to exemplify respectively, treatments with (1) rare-earth metals, (2) rare-earth metal oxides, and (3) an untreated set as a control. The development of melting, casting and rolling practices is described and discussed. Lance injection of oxygen shortly after melt raised the temperature of the metal immediately as much as 500° F., principally because mechanical agitation exposed the high-carbon metal to the flame and furnace root. An exceptional degree of superheat in the metal at the termination of the refining period was attributed to oxygen injection during the refining period. Bath temperatures higher than industrial practice were permitted by the all-basic furnace lining. Rates of carbon elimination as high as 0.036 percent carbon per minute were achieved by oxygen injections.

Jan 1, 1961

By R. S. Dean

The development of metallurgical processes may be divided into periods : First , the discovery of a basic reaction which brings about the production of the desired product from the available raw material ; second , a long stage of mechanical development during which little or no attention is paid to the reaction itself ; and third , a careful study of the reaction . Most metallurgical processes are to -day approaching the end of the second period . This we may illustrate by the steel process . The reaction of carbon with iron ore to produce pig iron and the subsequent refinement of the pig iron by an oxidation reaction is very old . Development in modern times has been almost entirely mechanical , the development of the blast furnace , furnace , the Bessemer process , the Siemens process , and even the Aston process for wrought iron being mechanical improvements almost entirely . Metallurgy is now entering a phase where the reactions are being considered . The question of how far can they be made to proceed is being repeatedly asked . As mechanical processes are improved , we approach a limit to which our basic reactions can be pushed which is determined by the nature of the reactions themselves . We want to know : How far can iron be decarbonized by iron oxide ? How low can the oxygen of copper be reduced by any given reaction? How efficiently can the fuel in a zinc reduction process be used ? The demand for purer metals and lower production costs has forced these and similar questions upon us . How are we to answer them ? The determination of these equilibria or end points of metallurgical reactions by direct means is fraught with difficulty because here we must overcome mechanical difficulties which too often become the limiting factors even in the laboratory and we do nottherefore get the actual limit to which the reaction itself may be carried . Further , there are so many reactions of metallurgical materials that to survey each separately is a job to give pause to any experimenter or group of experimenters .

Dec 1, 1930

By John K. Alley

Fibrous silicon carbide was produced by thermal decomposition of certain silicates contained in graphite crucibles. Induction heating was used to produce the necessary temperature and thermal gradients. Both green and white fibers were mainly the beta modification even though each color grew within a different temperature zone. Alpha silicon carbide, present in insufficient amounts for X-ray detection, was identified by electron diffraction. The white fibers formed in a zone between 1,365° and 1,634° C (±50° C). The green fibers (less contaminated) formed in a much more narrow zone between 1,650° and 1,672° C (±50° C). The average lengths and widths of microscopic fibers grown by this method were 1.5 mm/0.002 mm (white) and 1.2 mm/0.0035 mm (green); however, same fibers observed by electron microscope had cross-sectional measurements of 150 to 300 A. Both differential thermal analysis and thermogravimetric analysis showed that silicon carbide fibers oxidized in air at temperatures above 500° C. Fibrous silicon carbide was indexed as a cubic cell with the dimensions a = 4.358 A. The density calculated from X-ray data was 3.217 g/cm3.

Jan 1, 1963

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966

By John R. Dudo

The Bureau of Mines Morgantown Petroleum Research Laboratory, with the cooperation of the Penn York Oil Company, cored the Dewdrop, Bradford Third, Lewis Run, and Sartwell sands in the Sartwell oilfield, McKean County, Pa. This report contains a review of the geology and depositional history of the field and an evaluation of the feasibility of secondary recovery of oil from the Bradford Third and Sartwell sands by waterflood or gas drive. Core analysis, geologic data, and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Reservoir geometry, rock properties, fluid characteristics and saturations, and relative permeability-saturation relationships were used to assess the floodability of these two sands. The results of this study indicate that between 53,000 and 61,000 barrels of oil can be recovered by water or gas injection. The success of a waterflood or gas drive will depend on the field injection rates of the reservoirs comprising this oilfield. Following an economic evaluation, additional field work is recommended to further test the floodability of the reservoir.

Jan 1, 1967

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By N. A. C. Smith

This report on the physical and chemical properties of typical crude oils of southern Louisiana and southern Texas is the seventh in a series of preliminary chapters of a bulletin covering the producing districts of the United States. Preceding reports* may be obtained from the Bureau of Mines on request. The details of the methods used in this survey in collecting samples and making laboratory tests have been discussed in the first three papers. A method of summarizing and interpreting the laboratory data has also been given, but most of the crudes included in the present report differ so radically from those previously reported, that it has been found advantageous to adopt a somewhat different method in making summaries. This method is described in detail later. If any errors or omissions are noted by readers, it is hoped that these will be brought to the attention of the Bureau of Mines, for correction before the appearance of the final bulletin.

Jan 1, 1922

By Abrasive Materials

Table 1.-Salient abrasive statistics in the United States [ ]

Jan 1, 1967

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By Claude A. Tongish

This Federal Bureau of Mines report presents information on the accumulation and distribution of helium in U.S. natural gas reservoirs. The investigation concerns the relationship or association of helium with geographic location, geologic age, reservoir depth, nitrogen, carbon dioxide, and argon. Although helium is a minor constituent in natural gas, these data show that certain conditions make some reservoirs statistically more favorable than others for the accumulation of helium. The report is based on gas analysis information collected-by the Bureau from 1917 to 1974 from 10,086 gas samples, representing 6,455 reservoirs in 35 States. The occurrence of helium in the reservoirs was 11.5 percent with less than 0.005 percent of helium, 70.9 percent with 0.005 through 0.29 per-cent of helium, and 17.6 percent with 0.30 percent or more of helium in the gas. Results of the various correlations are presented in tables and charts. Relationships have also been determined quantitatively by measures of correlation. The statistical data can be used to determine the environment under which reservoirs with high-helium contents are most likely to occur. These data can be used with other information for predicting the future helium resources of the United States.

Jan 1, 1980

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By W. R. Gilliland, G. W. Jones

"One-phase of the accident prevention program of the Bureau of Mines is the determination of the explosion hazards of various combustible gases and vapors encountered,mining and allied industries and the development of means and methods of eliminating them.Gasoline is foremost among the combustible-liquid's as to quantity used and variety of applications in industry, It is a chief contributor to the causes of fires and explosions, taking an enormous yearly toll in property damage and considerable loss of lives.The results presented in this report evaluate the effect of various gaseous inert substances, which owing to their chemical composition, should be of considerable value in the prevention of gasoline fires and explosions. The substances investigated are as follows: Nitrogen (N2), automobile exhaust gas (85 percent N2 + 15 percent CO2), carbon dioxide(CO2), dichlorodifluoromethane (CCl2F2-Freon-12), trichloremenofluoromethane (CC13F-Freon-11), and dichloromonofluoromethane (CHCl2F-Freon-21).The general term ""gasoline"" designates a combustible liquid of such characteristics as to give satisfactory operation without preheating in spark-ignition-type internal-combustion engine. It comprises a complex hydrocarbon mixture having a limiting distillation range and produced commercially by distilling or ""cracking"" crude petroleum or other various petroleum stocks. Small proportions of other substances may be incorporated in the gasoline to enhance its antiknock properties or operating characteristics in internal-combustion engines and to increase its stability during storage, transportation, and use.It is thus seen that gasoline may have rather wide variations of chemical and physical properties, and it would: appear that the results of any investigation dealing with one particular gasoline might not be applicable to other types. However, as indicated by the results given in this report, the inflammable properties of different gasolines at normal atmospheric temperatures are influenced largely the mars volatile hydrocarbons containing 5, 6, 7 carbon atoms- in the molecule, and that the heavier constituent of higher molecular weight have a minor influence on the inflammable properties at ordinary temperatures."

Apr 1, 1946

By J. S. Dunning

The objective of this research by the U.S. Bureau of Mines was to determine the effects of AI additions on the sulfidation resistance of Fe-Cr-Ni alloys. A series of Fe-Cr-Ni alloys with and without -additions of 4 pet AI were tested in a wet S vapor atmosphere at 677 C. A study of the morphology and composition of corrosion scales indicated a different corrosion mechanism for AI-free alloys compared with AI-containing alloys. Aluminum-containing alloys formed a compact, tightly adherent layer at the metal-scale interface that reduced corrosion rates by a factor of 3 to 10 compared with that of AI-free alloys. The thin, adherent AI-containing scale limited inward diffusion of 0 and S to the base metal and outward diffusion of Ni from the base metal. Aluminum-containing alloys formed a three-layer scale in oxidizing-S environments, while AI-free alloys formed a less protective two-layer scale.

Jan 1, 1989

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975