Search Documents

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By R. D. Dey, V. Castranova, J. M. Antonini, J. A. Blackford Jr.

Alveolar macrophages (AM) exposed to cytokines or bacterial lipopolysaccharide (LPS) produce the free radical nitric oxide (NO·) by an inducible nitric oxide synthase (iNOS). They also release reactive oxygen free radicals following exposure to silica dust. The purpose of the present study was to determine whether NO· is produced by rat AM and/or recruited leukocytes following the intratracheal (IT) instillation of silica. Male Sprague-Dawley rats (175 to 225 g) were IT instilled with either silica dust (10 mg/100 g body wt) or LPS (0.25 mg/100 g body wt). After 24 h, bronchoalveolar lavage cells (BALC) and lavaged lung tissue were assayed for iNOS mRNA. Cell counts of BALC and iNOS-dependent (Nw-nitro-Larginine methyl ester [L-NAME]-inhibitable) chemiluminescence generated by AM were also determined. Northern blot analysis demonstrated that the steady-state levels of BALC iNOS mRNA were significantly increased by 3-fold following IT silica and by 7-fold following IT LPS. Partially enriched fractions of either AM or leukocytes from silica-treated rats both exhibited significantly elevated iNOS mRNA in Northern analysis. iNOS-dependent chemiluminescence was significantly increased in AM by 36-fold following IT silica and by 89-fold following IT LPS. Differential counts of BALC showed that AM numbers did not change in any of the treatments; however, red blood cells increased by 30-fold following IT silica and by 23-fold following IT LPS. Total leukocytes (polymorphonuclear leukocytes plus lymphocytes) increased by 58-fold following IT silica and by 274-fold following IT LPS. The results demonstrate that AM and neutrophils iNOS steady-state mRNA levels, AM iNOS-dependent chemiluminescence, and lavagable red blood cells and leukocytes all increased following IT silica. These findings suggest that NO· production in rat AM and neutrophils is increased in response to silica. NO· has the ability to then combine with superoxide and form a highly reactive toxic species, peroxynitrite, which may be responsible in part for silica-induced lung damage.

Dec 1, 1995

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile coal in the usual type of byproduct-coke oven, because they expand excessively and exert side thrust, which ruins the oven walls. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking, coals with as much low-volatile coal as possible and still have a mixture that will not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile coal has been exceeded and ovens have been damaged. It is desirable, therefore, to rave a reliable method of determining the expanding tendencies of mixtures before they are charged into the ovens. Furthermore, coal charges somewhat in its properties as mining progresses, and therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used.]

Jan 1, 1938

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness_ It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 33 to 40.0 pct. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3+3 sequence) ranged from 13.3 to 63.3 pct.

Jan 1, 1991

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By Louis C. Brichta

The Kline tract ?3.nd the Frey tract are two separate properties situated in the Wentworth district on the easterly edge of the Tri-State zinc-lead region (fig. 1). The Kline tract is in the southwestern corner of Lawrence County, Mo., and the Frey tract, 1 1/2 miles west of the Kline, is in the northeastern part of Newton County, Mo. A bureau Of Mines drilling project embraced work on both properties, but the amount of work done on the Frey tract was comparatively small. At the time of the project the Kline tract was under lease to the Wentworth Mining & Milling Co. The Surprise Mining Co. held the lease on the Frey tract. Underground workings on the generally flat-bedded are deposits of the Kline property-covered an area of-about 15 acres. No total metal-production records are available. In 1942-1943 the mine, operated by the Wentworth Mining & Milling Co., produced at an average monthly rate of 83 tons of 60-percent zinc concentrate derived from mining and milling 1,700 to 2,100 tons of ore. At the end of that period no significant amount of reserve ore was in sight. The gravity-flotation mill on the property was operating at about one-sixth capacity.

Jan 1, 1949

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By Marvin E. Lane

This paper , which describes the mining methods and practices at the Hayden Creek lead mine of St. Joseph Lead Co. in southeast Missouri , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The Hayden Creek mine is in the W 1/2 sec . 7 , T. 36 N. , R. 4 E. , St. Francois County , Mo. , about 1 mile southwest of the town of Frankclay ( fig . 1) . The mine is on the west edge of the mining district known as the Lead Belt . However , neither the ore body nor the underground workings are connected with those of any other mine in the district . In contrast with most operations in the district , underground haulage is entirely trackless , and nearly complete delineation of the large , well -defined ore body by drilling permitted comprehensive planning of development and mining in advance of shaft sinking . The ore differs in character and occurrence from that of the main ore deposits in the Lead Belt in that the lead mineral , galena , occurs in the dolomitic matrix enclosing granite boulders instead of in dolomite limestone .

Apr 1, 1957

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

By P. G. Clites

The Bureau of Mines developed techniques for induction melting of titanium in a split, water-cooled copper crucible. Calcium fluoride, which was used as an inert slag cover during melting, formed an insulating layer of solid slag between the ingot and the crucible wall. This thin layer of slag effectively insulated the ingot from the crucible and prevented the molten metal from shorting across the slits between adjacent segments of the crucible. The technique provides a means of melting loose titanium sponge and scrap and eliminates the need for fabricating a consumable electrode. This report describes the equipment developed and compares ingots produced from two varieties of titanium sponge, from titanium scrap, and from previously melted titanium with ingots prepared by vacuum-arc melting and electroslag melting. A melting scheme was also proposed and evaluated whereby loose titanium sponge was consolidated into a first-melt ingot for vacuum-arc remelting.

Jan 1, 1969

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By Robert R. Perron

The U. S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 15 to 30 ampere fault to ground, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1975