Search Documents

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By E. H. Rose

This paper, describing the concentrator practice of the Moctezuma Copper Co., is one of a series being prepared by the Bureau of Mines. The Nacozari concentrator of the Moctezuma Copper Co. (the Mexican subsidiary of the Phelps Dodge Corporation) is located about 75 miles south of Douglas, Ariz., in the Moctezuma District of the State of Sonora. Nacozari is the southern terminus of the Nacozari Railroad, ever which all concentrate is transported to Douglas for smelting.

Jan 1, 1930

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By W. A. Calhoun

This investigation of low-grade bauxites as potential sources of aluminum by caustic desilication and alumina extraction was undertaken by the Bureau of Mines to develop extractive methods for winning alumina from domestic deposits of low-grade bauxites. This report is the second of a series covering the work by the Bureau of Mines' Rolla, Mo., and Bauxite, Ark., laboratories. The first report published in the Journal of Metals, December 1951,3/ and dealt with kaolin and halloysite. The present investigation is concerned with low-grade bauxites only. The purpose of these investigations is to increase the domestic supply of aluminum ores. With eventual depletion of high-grade deposits, aluminous materials, such as low-grade bauxite, clays, shales, and high-iron laterites, will become our principal domestic sources of aluminum. The development of extractive processes for winning alumina from these low-grade materials is one of the many national security measures undertaken by the Bureau of Mines. A method has-been developed in the laboratory for successfully treating high-silica bauxites from domestic deposits. In this process the bauxite was calcined at 980° C. to form amorphous silica and alumina. The calcine was then leached by percolation with 15-percent sodium hydroxide solution at 940 to 96° C., removing 67 to 77 percent of the silica with a loss of 4.1 to 5.0 percent of the alumina. The sodium hydroxide in the spent liquor used in desilication was 95 percent recoverable, and comparable desilication results were obtained with 100-percent reclaimed liquor, The indicated cost of reagents, for sodium hydroxide and lime used in the desilication and regenera¬tion of spent liquor, was about $4.00 per ton of calcine treated.

Jan 1, 1954

By W. H. Young

MOST OF THE key items in the bituminous-coal and Lignite industry declined in 1954 compared with 1953. Production, consumption, exports, average value per ton, men working, and days worked all declined; however, in the field of mechanization, the percentages mechanically loaded, mechanically cleaned, mined by auger, and mined by stripping all increased, as did production per men per day. Production.-The output of soft coal in 1954-391.7 million tons- was 14 percent less than the 457.3 million tons produced in 1953. The lower production in 1954 was due largely to a sharp reduction in consumption in the United States and to a drop in exports.

Jan 1, 1958

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX C - HOISTING SYSTEMS - AVAILABLE EQUIPMENT C 1 - Introduction A survey has been made of available hoisting equipment which has applications for use in metal and non-metal mine emergency escape hoist systems. The information was gathered from a number of sources, including representatives in the USBM and MESA, mine operators, personal visits and telephone interviews with manufacturers, field visits to inspect equipment, advertisements, catalogues and indices of manufacturers. Wherever possible, technical specifications and prices were checked out with the manufacturer, or supplier. The sections on individual sub-systems and components, such as automatic control systems, winches and controls, are not intended to be all encompassing surveys. Rather a reasonable number of representative units in each category are discussed. The sample is large enough to provide a general picture of the kind of equipment available, including the abilities and limitations and a reasonable price range. The survey has been divided into six categories 1. Complete Hoisting Systems A Above ground installations B Below ground installations 2. Hoist Assemblies ^(Man-rated) 3. Hoists (not Man-rated)

Jan 1, 1976

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d&apos;Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d&apos;Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

By Jeffrey Y. Foley

In 1980, the Bureau of Mines investigated the northern Darby Mountains on the Seward Peninsula, AK, for radioactive mineral deposits. Uranium is concentrated in silicified shear zones in biotite quartz monzonite of the Darby pluton. The shear zones are best exposed in steep, narrow, avalanche gullies; they are characterized by radiometric anomalies and by uranium and thorium geochemical anomalies. Radiometric and geochemical anomalies are also found over altered biotite quartz monzonite where there are no visible shear zones. The radiometric and uranium anomalies are often spatially, but apparently not genetically, associated with alkaline mafic and felsic dikes. Similar geochemical and radiometric anomalies over discolored altered zones and geochemical anomalies in sediments downstream from the altered zones indicate that additional areas may also be favorable targets for uranium deposits. Analyses of panned, heavy mineral concentrates show no significant concentrations of uranium or thorium in resistant heavy minerals. This indicates that radioactive elements in the Darby pluton are concentrated in soluble, nonresistant minerals that may constitute a recoverable uranium resource.

Jan 1, 1986

By George E. Fish

This report describes investigations conducted by the Bureau of Mines from 1957 through 1959 in the Roseland anorthosite-titanium belt of Nelson and Amherst Counties, Va., for the purpose of studying the titanium resources of the area. Three titanium deposits containing much saprolite ore derived from the decomposition of anorthosite and diorite were selected for detailed study Following a reconnaissance of the reported titanium occurrences in the belt. These three deposits occur in or are associated with anorthosite. Most of the occurrences are situated on or near the contact between the anorthosite and the gneissic country rock. The saprolite deposits are as much as 1.5 miles long, 1,000 feet wide, and 100 teat deep and contain significant reserves of titanium-bearing material estimated in excess of 20 million tons. Where it was penetrated by drilling, the unweathered rock beneath the saprolite contains nearly the same titanium values as the saprolite.

Jan 1, 1962

By J. M. Kuchta

Concentrated hydrogen peroxide (H202) is a highly reactive oxidizing agent that liberates heat when it decomposes. The heat liberated may be sufficient to ignite combustibles with which the peroxide comes in contact. For this reason, concentrated hydrogen peroxide should be handled only by personnel familiar with its many unique properties.6 Hydrogen peroxide is used as a bleaching agent in the manufacture of textiles; this is its major single use in the United States. It is also employed as a reagent in chemical synthesis, as a source of free radicals to start polymerization, as a foaming agent in the manufacture of porous substances, and for its effect on biological processes. Moreover, highly concentrated hydrogen peroxide is a compact source of energy that can be utilized both as a monopropellant and as the oxidizer in a bipropellant system, During World War II, large quantities of highly concentrated hydro- gen peroxide were used as propellants, particularly in Germany. Since then, production of the peroxide has increased rapidly; in the United States alone it has more than doubled since 1950.7 Because of its widespread use, increasing interest has been shown in the hazards of handling the high- strength peroxide.

Jan 1, 1961

By W. M. Mark

This investigation was undertaken to develop methods to improve the quality of titanium sponge produced by the Bureau of Mines modification of the Kroll magnesium reduction process. Research revealed that by systematic elimination of detrimental impurities introduced with the raw materials and by improved handling and processing techniques, high-quality ductile titanium with a hardness of less than 110 B.h.n. (Brinell hardness number) can be produced consistently. This improvement was accomplished by helium (or argon) stripping of residual atmospheric and other dissolved gases from the titanic chloride, preliminary dehydration of crude titanium sponge, and careful regulation of the titanium tetrachloride (TiC14) feed rate to the reactors.

Jan 1, 1960

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962