Search Documents

By C. H. Riggs

THIS REPORT give's the results of a study of the central and south parts of the Cushing oilfield, including a description of the geology, a review of the production history, and estimates of oil reserves available by secondary-recovery methods. Each of the major producing zones of the field is treated separately. The report, which is one of a long series of field studies the Bureau of Mines has conducted over the past 40 years, was prepared to aid operators to increase oil recovery and to help prevent underground waste in the Cushing field, in the State of Oklahoma, and in the United States. The geology and production history are presented not as a review of past behavior of the Cushing field but rather to interpret the possibilities for increased oil recovery by future development of this and similar areas. The field, which is in the northwest corner of Creek County, Okla., was discovered in 1912 and developed during 1913 and 1914. For several years it, was one of the most important areas producing high-grade crude oil in Oklahoma. Although some oil has been recovered from each of 10 separate reservoirs, nearly 98 percent of the total recovery of oil in the area studied was from 4 major producing formations (table 1). Of these, only the Bartlesville [ ]

Jan 1, 1958

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By H. B. Hill

The Salt Flat field, formerly called the Joe Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately N. 20 to 45° The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1926, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting.

Jan 1, 1931

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By Noel N. Moebs

The Bureau of Mines studied the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian region. All relevant published literature pertaining to the occurrence and control of surface and ground water in underground coal mines was reviewed, and the impacts of mine water with respect to health and safety, production, environment, and costs were assessed and are described in this report. The report also identifies the sources of water inflow into underground coal mines, and gives a summary description and evaluation of techniques that can be used to reduce the amount of water entering these mines. Engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings were reviewed and are summarized. Major emphasis has been placed on the identification of geologic and hydrologic conditions of the site, the water control methods used, and an evaluation of their technical and cost effectiveness.

Jan 1, 1985

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22).4 and sulphur content by the lamp method.5 Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.6

Jan 1, 1931

After a stagnant performance in 1982, gross national product (GNP), industrial production, and employment increased during 1983 in nearly all industrial nations, with the U.S. performance generally leading the uneven worldwide recovery. Real U.S. GNP increased 3.3 percent in 1983 (table I). Although investment in nonresidential structures declined, total nonresidential fixed investment in the United States was up 1.5 percent following a 1982 decrease. The increase in worldwide industrial activity and demand in 1983 put greater pressure on prices in many countries. Prices increased from less than 3 percent in the Federal Republic of Germany, Japan, the Nether-lands, and Switzerland to as much as 10 percent in nearly all the other Organization for Economic Cooperation and Development nations. The annual inflation rate in the United States was 4.3 percent (based on the GNP fixed-weight price index).

Jan 1, 1984

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22),4 and sulphur content by the lamp method. Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.

Jan 1, 1931

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

[ ]

Jan 1, 1975

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960

By K. K. Kelly

METALLURGICAL thermochemistry of titanium is a broad subject and (if data were available) could include a wide variety of topics. The present report is restricted to extractive metallurgy and to substances and reactions that bear upon the magnesium, sodium, and hydrogen-reduction processes employing titanium tetrachloride. The aim has been to present enough data so that the reader not only can check: the calculations for the reactions discussed but also can conduct related calculations if he so desires, without recourse to other compilations of data. The subject matter divides naturally into two parts-the selection of the data to be adopted and the application of these data to pertinent metallurgical reactions.

Jan 1, 1959

By Michael J. Sapko, Kenneth L. Cashdollar

In This Chapter [Methane ignition as initiation source for much larger secondary coal dust explosions Rock dusting requirements to prevent coal dust explosions Dangers of hybrid mixtures of methane and coal dust] Although methane explosions are dangerous, those that involve coal dust are even more so. If exploding methane disperses and ignites the coal dust that has accumulated on the mine ribs and floor, the burning coal dust immeasurably increases the strength of the explosion. Such methane-dust explosions are prevented by inerting the coal dust in a way that prevents the exploding methane from igniting it. This chapter discusses the dust hazard and how it is pre-vented in U.S. coal mines. METHANE IGNITION AS INITIATION SOURCE FOR MUCH LARGER SECONDARY COAL DUST EXPLOSIONS The typical scenario for coal mine explosions starts with the ignition of a flammable methane-air atmosphere near the face. The turbulent winds from the primary methane explosion then disperse the coal dust. If there is insufficient rock dust (usually limestone), a secondary coal dust explosion then propagates throughout large sections of the mine. These scenarios have been studied extensively at the Bruceton Experimental Mine (BEM) and the Lake Lynn Experimental Mine (LLEM) of the NIOSH Pittsburgh Research Laboratory. The minimum quantity of methane required to initiate a coal dust explosion was studied in 1930 in the BEM [Rice et al. 1933; Nagy 1981] and then later in the LLEM, whose cross-sectional area (130 ft2) is over twice that of the BEM [Sapko et al. 1987a]. Studies conducted in the BEM closely simulated conditions that existed in operating mines in the early 20th century. The later tests in the 20-ft-wide entries of the LLEM simulated the geometries of modern mines with advanced roof support technology. The data from the BEM tests show that 13 ft3 was the minimum quantity of methane at the face that, when ignited, would disperse and ignite coal dust. In the BEM, this amount of methane was mixed with air to form a total flammable volume of about 140 ft3 of a 9% methane-in-air mix-ture. In the wider entries of the LLEM, about 37 ft3 of methane was required to disperse pure coal dust and start a self-sustained coal dust explosion. This amount of methane was mixed with

Jan 6, 2006

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943