Search Documents

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By W. A. Selvig

EQUIREMENTS of montan wax for industrial use in the United States before World War II were met by imports, nearly all of which came from Germany. An important industry for extraction and refinement of this wax from certain brown coals had developed in Germany. At the beginning of the war, montan-wax imports were shut oft, and American industry was forced to rely largely on substitutes. Since the war, relatively small amounts have been imported from Czechoslovakia. Because of the shortage of montan wax at the close of the war and the fact that industry in the United States had to rely on foreign sources in the past, this investigation was started in 1945 to determine probable yields of wax from domestic lignite. Results of the investigation and the properties of extracted waxes are described in this report. Also included in the report are discussions of the occurrence and geology of lignite deposits of the United States from which samples were obtained for wax extraction and the petrographic composition of lignites, particularly in respect to those components that contribute to wax yields.

Jan 1, 1950

By Y. H. Cheng, D. M. Lewis, V. Castranova, M. W. Barger, J. K. H. Ma, J. Y. C. Ma, W. F. Xin

Bis-basic ethers off fluorene and fluoren-9-substituted derivatives such as tilorone have been reported to inhibit silica-induced fibrosis in rats. The potential antifibrotic potency of 2,7-bis (diethylamino) ethixy fluorine fluorenone (F-9-H.H), fluorenoxime (F-9-one), and fluorenol (F-9-ol) was F-9-axime > F-9-one ~ F-9-H,H > F-9-ol. Since the release of reactive oxygen species and growth factors from alveolar macrophages (AM) in response to silica exposure has been linked to the development of pulmonary fibrosis, the present study was carried out to determine the inhibitory effects of these compounds on rat AM activity in vitro. The following parameters were monitored: (1) cellular viability; (2) zymosan-induced respiratory burst activity (superoxide and hydrogen peroxide release, chemiluminescence, and oxygen consumption) of AM; (3) drug binding to AM; and (4) lipopolysaccharide (LPS)-stimulated interleukin- I (IL-1) release from AM. The bis-basic ethers, at 40 did not affect cell viability when incubated with AM for 30 min, but significantly inhibited zymosan-induced macrophage respiratory burst activity. The inhibitory effect of these agents was F-9-oxime > F-9-one ~F-9-H,H > F-9-ol. Binding of these drugs to AM was time and dose dependent, and exhibited the following binding affinity: F-9-oxime > F-9-one > F-9-H,H > F-9-ol. F-9- oxime was shown to inhibit LPS-stimulated IL-I release by AM in a dose-dependent manner. This inhibition of IL-1 release by AM cannot be explained as a decrease in viability. In addition, these drugs were also shown to impair human fibroblast proliferation in response to serum stimuli without impairing cell viability. These results indicate a positive correlation between drug binding to AM or other cell types and their inhibitory effects on cellular activities including oxygen consumption, superoxide release, hydrogen peroxide secretion, chemiluminescence, IL-I release, and proliferation. The ability of-these bis-basic ethers to modify AM and fibroblast functions in vitro suggests that further investigation of their reported antifibrotic potency in vivo is warranted.

Dec 1, 1996

By Robert C. Hickman, Xavier B. Starnes

"The general location of the Kentucky, Fluorspar District and the Moore Hill fault area are shown in figure 1. An engineer3/ the Bureau of Mines visited the district in July 1942 and reported on the Moore Hill fault system. Subsequently the Bureau explored the Summers, Pepperbox, McCune, Eagle-Watson, Henry Watson, Davenport, Felix Tyner, and Eagle-Wring prop¬erties by core drilling. These properties and the principal faults are shown on figures 2 and 3.Collaboration of the Federal Geological Survey4/ was of great benefit, particularly in mapping the properties, determining the stratigraphy, and furnishing information on that and other geologic factors.Fluorite was noted as early as 1818 near Shawneetown in southern Illinois.5/ In 1835 an attempt was made to work deposit in Crittenden County, Kentucky, but interest centered chiefly upon the galena found with the fluorite. The first shipments of fluorspar from Kentucky wore made in 1373 from the Yandell mine of Crittendon County.6/ It is not known when the first work on the Moore Hill fault was done, but it seems probable that the Cullen-Eagle and Nancy Hanks were being ,worked in 1900. Gravel spar was found on the surface at the Two Brothers mine in 1904,7/ and the main shaft was started in 1914; work also began at .the Davenport in 1914, and in 1917 the Eagle-Watson was in production. A shaft was gunk on the Pepperbox in 1918, and in 1922 fluorspar was found and work was started on the Summers property. In 1924 work began at the McCune, Felix Tyner, Eagle-Wring, and probably the Hicks properties.No Good approximate record of production from each property on the Moore Hill fault system is obtainable, but an estimate based upon all data available is as follows:"

Sep 1, 1946

Numerical models play a significant role in the design of safe underground mining excavations and support systems. Advances in the capabilities of numerical modeling software, together with ever increasing computational speeds, have made it possible to investigate the very nature of the large-scale rock mass and its response to mining excavations. The improved understanding of the rock response obtained from modeling enhances our designs, resulting in greater stability and safety of the mining excavations. To help advance the state of the art in this field, the National Institute for Occupational Safety and Health organized the International Workshop on Numerical Modeling for Underground Mine Excavation Design. The workshop was held in Asheville, NC, on June 28, 2009, in association with the 43rd U.S. Rock Mechanics Symposium. The proceedings include 10 papers from leading rock mechanics and numerical modeling experts in the United States, Canada, Australia, and Germany. The papers address a wide range of issues, including various numerical modeling approaches, rock mass modeling, and applications in coal and metal mines.

Jun 1, 2009

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

By John J. Mulligan

Coalbeds were discovered in outcroppings of the Beacon group of sediments on the north end of the Willett Range ( altitude 77 ° 11 ' S , longitude 160 ° 20 ' E ) , Victoria Land , Antarctica , in December 1960 during an investigation undertaken as part of the U.S. Antarctic Research Program under the auspices of the National Science Foundation . Three separate exposures of coal or coaly material were found . Two of the exposures contain , respectively , eight and four beds of hard , compact , finely banded attrital coal ranging in thickness from 8 feet downward to a few inches , and reported to range in rank from mediumvolatile bituminous to semianthracite . The coals are associated with carbonaceous shales containing an abundant assemblage of fossil plants resembling those associated with the Permian coals of Australia and other Gondwana areas . The third exposure , apparently somewhat higher in the stratigraphic sequence , contains only coaly plant fragments scattered through a thin conglomerate and overlying sandstones . A sandstone bed that overlies these coal - bearing sandstones contains abundant logs and fragments of silicified wood . Preservation of features is poor , but one segment of a silicified stem suggests comparison with Rhexoxylon , a gymnospermous tree that usually is considered indicative of Triassic age . The Beacon sediments in this area have been invaded , broken , and uplifted by a massive series of diabase sills and dikes greater in volume than the intruded sediments . The heat emitted by these intrusives must have advanced the metamorphic development of the coals . However , there is no evidence of alteration to graphite , and coal found in direct contact with a diabase sill contains no vesicles or other usual evidences of natural coking . Either the pressure of overlying rocks inhibited the development of coke , or the coals had been metamorphosed beyond the coke forming stage before the igneous intrusion .

Jan 1, 1963

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By Joel N. Van Sant

THIS REPORT describes the occurrence, mining, and use of refractory clay in Colorado within Region III of the Federal Bureau of Mines, which includes the States of North arid South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona. Field work by the Bureau of Mines, United States Department of the Interior, included examination of active and abandoned refractory-clay mines as well as a reconnaissance survey and sampling of numerous clay-bearing formations exposed in Colorado. Information from the survey and the sampling will help guide private industry in its search for virgin sources of refractory clay. Library research of published and unpublished reports from various Federal, State, and private sources was conducted during the early phase of the investigation. Most of the refractory clay mined in the Denver-Golden district of Colorado is not used for refractory purposes but is blended with other clays in the manufacture of structural clay products. The predominantly flint-clay de-posits in the Pueblo and Fremont County districts are mined and utilized chiefly in fabricating refractory products.

Jan 1, 1959

By G. Boehler

The purpose of this program is to demonstrate the feasibility and practicality of noise control for secondary and tertiary crushers in surface non-coal mining plants and mills. It is a part of the broad Bureau of Mines program to reduce noise in mines to levels mandated in the Coal Mine Health and Safety Act. Utilizing the results of previous contractual research efforts in which noise levels of secondary crushers had been measured, two noise enclosures were designed and evaluated for the REXNORD Symons 7-ft diameter secondary and tertiary crushers installed at the Jackson County Iron Company, in Black River Falls, Wisconsin. The first enclosure had a circular shape following closely that of the crusher and was built up entirely of quick-release panels which can be handled by the crusher operator alone. The second enclosure was octogonal in shape and can be rapidly removed, partially or totally using an overhead crane. Both enclosures fully satisfy the noise reduction objectives and permit daily and long-term maintenance of the crushers. Cost analyses show the cost of the enclosure to be less than 10 per cent of the cost of the crusher, the cost of the octagonal enclosure being estimated at only 60 percent of that of the circular one, e. g. $15,000 against $25,000. It is concluded that the octagonal enclosure best meets the needs of the Jackson County Mining Company and it is recommended that an experimental enclosure be built at the earliest possible time, as proof-of-concept.

Jan 1, 1977

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975

By Floyd R. Hertweck

This Bureau of Mines publication contains analyses and related source data for 349 natural gas samples from 26 States and 2 foreign countries. The 3 samples from foreign countries and 339 of the U.S. samples were collected during calendar year 1983. The remaining seven samples were collected earlier, but releases granting permission to publish were not received until 1983. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-seven publications have presented the results of 13,332 gas analyses made prior to 1983. The first three bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-27) containing 8,104 analyses of sam¬ples collected since 1960.

Jan 1, 1984

By Oliver Bowles

"Underground operation.In its broader sense the term ""mining"" is applied to all processes whereby raw materials are taken from the earth to be used as sources of mineral products. In a more restricted sense ""mining"" is applied to underground operations as contrasted with open pit work designated as quarrying. The tern is used in the restricted tense in this paper; for it relates to the exploitation of limestone deposits by modern methods of underground operation rather than by open pit methods.Present tendency toward miningIt may seem to some readers that a paper on mining limestone will find little general interest among lime plant operators, for only a limited number of them have yet resorted to this means of procuring raw materials. It is noteworthy, however, that a growing tendency exists toward underground operation, for one by one quarry owners are faced with increasing difficulties in open pit operation. It seems desirable, therefore, for operators to keep closely in touch with this gradual change in process, to inquire into the underlying causes, to compare costs, and to study the effects of the change in method on subsequent steps in calcining the stone to produce lime."

Mar 1, 1924

By R. R. Sayers

The hazards connected with work under abnormal air conditions are becoming of increasing importance from a financial as well as a physiological stand- point, due to the extension of compensation laws to include diseases caused by dusts, toxic gases, and abnormal temperatures and humidities. The United States, with the excention of California, North Dakota, Wiscon- sin, Massachusetts, and Connecticut, is the only English-speaking country to-day where silicosis is not compensated.3 Cases of permenent total disability or death due to silicosis mar aprear in common-law courts, particularly in the States that have not recognized silicosis as an occupational disease for which compensation should be provided. Such cases have recently been tried in one State, according to a magazine editorial, not providing scheduled commensation for employees affected by silicosis, with results favorable to the claimant. Clearly established cases definitely linked with occupation as the cause may be expected to be recognized as deserving by juries and courts, and awards will be made. In one Atlantic Coast State, according to this editorial, 108 claims for silicosis, including 21 deaths therefrom, are said to have been filed against two small plants engaged in finely pulverizing quartz sand.

Sep 1, 1932

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982