Search Documents

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By S. S. Venkata

This volume describes a comprehensive program of research into the reliability of mine electrical power system components and the resultant reliability of the total system. The research effort encompassed analytical models, laboratory testing and field testing. The analytical work included definition of terms, fail rate functions and distributions, failure rate estimation and techniques and procedures for theoretical reliability assessment. One of the primary mine power system components addressed in the study was the ac molded case circuit breaker. This device is known to have low reliability and hence an unfavorable impact on mine safety and productivity. Ac molded case circuit breaker reliability was studied by analytical means, laboratory testing and field monitoring. A similar three-pronged' effort was made to study the reliability of undervoltage relays/releases. Particular emphasis was placed on new solid state undervoltage relays. The reliability of bulk power components, such as trailing cab les, motors, control gear, and other equipment, was assessed by gathering maintenance records from active mines. These data were compared to similar records from other industries. The work was extended to include the reliability, availability, maintainability and safety of these components.

Jan 1, 1979

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By J. R. Thoenen

During the past 6 years the Mining Division of the U.S. Bureau of Mines has prepared many information circulars containing valuable technical data covering the operating details of mining and ore-dressing plants throughout the United States, Canada, Mexico, and other countries. These papers, written for the most part by operating officials in the field, have been designed to comprise a reference library for the operating engineer. In order to make the information contained in these publications more readily available to the busy engineer the enclosed series of reference tables has been compiled. The tabular arrangement is by subject rather than alphabetical order, thus avoiding the bulk of an alphabetical index.

Jan 1, 1935

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By Gilbert A. Wray

This report presents the results of a study of the overturning Stability of Front End Loaders and the development of an Obstacle Detector to warn of Obstacles in the blind regions of the vehicle. The contributing factors have been identified, the FEL stability characteristics have been determined and six overturn warning indicators were fabricated and two were field tested in a mine operation over an extended time period. A simplified overturn indicator, based on the principle of sensing wheel load, was designed, constructed and field tested. The principle was demonstrated to be sound, however, the method of sensing wheel load must be revised. An obstacle detector capable of detecting a man sized target at ranges of two feet to one hundred feet was designed. A "Breadboard" device utilizing existing microwave devices was constructed and tested successfully.

Jan 1, 1977

By W. E. Dennis, M. M. Fine

"INTRODUCTION During peacetime, the United States uses less than 3,000 tons of chemical-grade celestite annually. The war need, however, was estimated to exceed 15,000 tons a year.Hitherto; most of the required chemical-grade ore has been imported from England, Mexico, and other foreign countries. If foreign sources do not find it possible to meet the demand for ore of chemical grade (plus 92 percent SrSO4), it is expected that requirements could be satisfied by concentrating low-grade domestic ores. Celestite deposits on Brown, Nolan, Fisher, and Coke Counties, Texas, are considered to be possible sources of supply for this low-grade material. The Bureau of Mines explored the most important deposits to determine the grade and amount of ore available and conducted ore-dressing tests to obtain a suitable method of concentration.The exploratory work, consisting of test pitting and sampling, was carried on under the direction of W. E. Dennis, one of the authors of this paper, from October 8, 1942, to January 30, 1943. The ore dressing-tests described herein were conducted at the Bureau of Mines Laboratory at Rolla Mo.In this report, a particular deposit is referred to by the name of the landowner on whose .property the .deposit lies. The location of the deposits investigated is shown on figures 1, 2, 3, and 4.The celestite deposits were previously studied by the Bureau of Economic Geology of the University of Texas, and the results of its investigation are published in Mineral Survey Circular No. 46."

Feb 1, 1947

By Michael R. Norland

This U.S. Bureau of Mines report on U.S. and Canadian 1iterature pertaining to soil characterization and the use of soil amendments as a part of the reclamation process of coal surface-mined lands contains 1,280 references. The references were published during the 1977 to 1988 period. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate those articles with the coal mining region and subjects of interest. All references are annotated.

Jan 1, 1991

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By Thomas E. Howard

Man has been engaged in the construction of tunnels in. rock for several thousand years. During that time, methods of tunneling have changed drastically. Hordes of men chipping away at the tunnel face have been replaced by mechanical drills and explosives and by tunnel boring machines. Spoil is no longer carried on the backs of humans, but is now removed by trains, trucks or conveyor systems. These and other changes have had the effect of greatly increasing the rate of tunneling, while at the same time, greatly decreasing the potential dangers to workmen. Although the techniques, equipment and material used for tunneling are being continually improved, rock tunneling is still a slow and expensive process. Significant improvements and innovations are needed to reduce the cost and time required for tunneling if we are to fully utilize the subsurface to aid in the solution of urban problems and in the conservation of resources. This report is intended to facilitate the orderly development of tunneling technology by focusing attention on the inadequacies of rock tunneling and the improvements that are needed. The data presented were derived from the results of a comprehensive questionnaire that was completed during the summer of 1969 by more than 600 individuals and organizations in 17 countries. Table 1 lists the countries and the number of replies from each. Appendix A contains a summary profile of the national responses, while the text presents the results and a brief analysis of the conclusions that might be derived from the data in the questionnaire. The data shown in Appendix A represent the consensus opinion of each of the 17 nations without regard to the number of individual replies or the amount of tunneling activity that is represented. The national consensus was determined for each country by a plurality of the individual responses, in some cases modified by the opinion of the rapporteur. Tire above procedures can lead to situations which are misleading. For example, experience and activity arc a rational basis for analysis; but, if national replies are weighted on this basis (i.e., number of responses), informed and valuable opinion of less active countries would probably be overwhelmed and lost. In analysing the data on the basis of national responses without weighting, it becomes apparent that many of the same problems exist under a given set of conditions regardless of the number of tunnels that have been driven.

Jan 1, 1970

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932