Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Monongalia County, W. Va. It is one of a Bureau of Mines series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.5 million tons of coal was produced in Monongalia County in 1957, of which more than 7 million tons was cleaned mechanically in 8 cleaning plants. On January I, 1954 the Bureau of Mines estimated that 1,576 million tons of recoverable coal remained in the county in beds 28 inches or more thick.

Jan 1, 1960

By Avery H. Reed

RECORD production of crude petroleum, lime, crushed marble, and talc highlighted the mineral industry of Alabama in 1963. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 86 percent of the total value of production, compared with 82 percent in 1962. The iron-ore industry continued to decline; in 1959 the value of iron ore produced was 12 percent of the total State production value; in 1960, 11 percent; in 1961, 10 percent; in 1962t 8 percent; and in 1963, 5 percent.

Jan 1, 1964

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By D. Harrington

"One of the underlying reasons for the establishment of the United States Bureau of Mines was the desire to promote greater safety in the mining and allied industries. Safety continues to be an important feature in the work of the bureau, and during the fiscal year 1929-30 the Bureau of Mines allotted $387,510 to the safety division out of a total appropriation of $2,249,670 (other than for helium).The safety division personnel consists of 22 engineers, 2 mine safety commissioners, 3 senior foreman miners, 18 foreman miners, 16 first-aid miners, 16 clerks, 10 cooks, and 3 laborers, a total of 90 persons. These safety workers are distributed through the 10 districts into which the United States has been divided for administration purposes. During the year 3 engineers, 1 senior foreman miner, 4 foreman miners, and 4 first-aid miners left the service. In general these men left the service to take up more lucrative positions.The 10 all-steel mine-rescue cars have headquarters as follows: Car 1, Reno, Nev.; Car 2, Raton, N. Mex.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa. There is also a mine-rescue car with headquarters at Juneau, Alaska. In addition, there have been established 11 mine rescue stations as follows: Birmingham, Ala.; Berkeley, Calif.; Seattle, Wash.; Evansville, Ind.; Jellico, Tenn.; McAlester, Okla.; Norton, Va.; Vincennes, Ind.; Wilkes Barre, Pa.; Salt, Lake City, Utah; and Pittsburgh, Pa.Every mine-rescue car and station is fully supplied with equipment and devices for use in case of mine fire or explosion, and at each station is an up-to-date automobile truck. At time of amine disaster the bureau's forces are immediately placed at the disposal of the authorities, State or company, with a view to giving such assistance as may be desired or available.The activities of the safety division at ordinary times are directed largely to securing and disseminating data on safety in mining. Among the numerous studies made, or being made, concerning safety and health in mining are those in connection with the causes and methods of prevention of mine explosions, explosibility of dust and gases, explosives and blasting, haulage, electricity, falls of persons or material, ventilation, dusts, high temperatures, timbering, lighting, machinery, and in fact practically anything which results or may result in acci¬dents of any kind in or around mines."

Nov 1, 1930

By J. F. Barkley

Smoke abatement is a subject of which fuel technology, although absolutely essential, is only a part. Its successful accomplishment starts and ends with human factors that must be given thorough consideration; between this "start" and "end" fuel technology is applied. Smoke abatement usually starts from the desire of some person or persons to be free from uncleanness caused by the stack of someone else and ends with the sincere desire of the operator of the fuel-burning equipment to maintain a clear stack. Although "smoke abatement been discussed for many years, it is only recently that the public has been mindful of such expressions as "air pollution" and "air hygiene." The subject has duel in common with that of supplying pure water but is more complicated. The public desires pure water, expects pure water, is willing to pay for pure water, and expects to continue to pay for it indefinitely; it is a development of civilization. It is doubtless correct to say, however, that people in general do not et realize the detriment of air pollution to their well-being or give the question enough serious consideration. This is illustrated by the fact that in city smoke abatement it is the mass of small householders that sins the most and is the hardest to handle. It is rather difficult to assemble a group of people in a room without the air becoming contaminated with smoke. Smoke abatement will lag with the lack of desire for pure air - probably the biggest human factor involved in its accomplishment.

Jan 1, 1939

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By P. M. Ambrose, C. Travis Anderson, Cresap Moss, R. S. Dean

"MANGANESE METALMethods of PreparationMethods of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century used Moissan's pyrophoric manganese. 5/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. It was essentially a pure material, and investigations in which it was employed (with proper precautions against oxida¬tion) led to accurate results concerning the intrinsic behavior of metallic manganese.An early investigation of the properties of ""Manganese-by-Mercury"" was made by M. Guntz. 6/ He prepared manganese by electrolysis of a concentrated MnCl2 solution with a mercury cathode. The manganese amalgam was pressed through chamois and distilled in vacuo (2 to 3 cm. of mercury) at 200°0., slowly rising to 250°0. Guntz recognized especially the decreased reactivity of manganese with increased temperature of mercury distillation. The most careful and com¬prehensive study of manganese made by this method is that of Kuh 7/ whose work unfortunately was never published in an accessible journal.Royce and Kahlenberg 8/ studied the electrode potential of manganese made by this method."

Nov 1, 1939

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1974 is compared with consumption in 1973 and 1975 (preliminary data).

Jan 1, 1977

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By K. K. Kelley

The first bulletin (269) 3 in this series, which appeared in 1932, compiled the entropy values then available for the elements and in-organic compounds, results being listed for some 150 substances. Elaborations and revisions followed in 1936 (272) and 1941 (280), when over 500 usable entropy values were tabulated. The present bulletin constitutes a further elaboration and revision. The accumulation of data since 1940 has been marked, and 800 entropy values now are available. The present bulletin also contains all the pertinent explanatory matter that appeared in its predecessors. Thus, it retains the same dual purpose of assembling the available values of the entropies at 298.16° K. of the elements and inorganic compounds and giving enough explanation of methods of calculating entropies to make the results comprehensible.

Jan 1, 1950

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982