Search Documents

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

Discussions of the papers with a written contribution on Paper No. 11 and authors' written replies. Also brief obituary of Dr. T. David Jones on p146.

Jan 1, 1947

"The sulphide nickel resources of Australia are concentrated in the Western Australian Shield. This shield is considered to have developed by extensive, but incomplete, Proterozoic reworking of once-continuous Archaean crust. It now constitutes relic Archaean cratons and intervening orogenic mobile belts transected by narrow, curvilinear tectono-thermal mobile belts of younger Proterozoic age. Remnants of the Archaean cratons are exposed in the Yilgarn and Pilbara Blocks. In the former an ancient (to ca 3600 m.y.) high-grade gneiss terrain (Western Gneiss Terrain) occurs along the western margin of the block and is interpreted to flank younger (ca3000-2800 m.y.) greenstone belts to the east. Ancient (to ca3500 m.y.) granitoid-greenstone terrains dominate the Pilbara Block.Proterozoic mobile belts contain only traces of nickel mineralization, except for one locality in the Halls Creek Province. The Archaean high-grade gneiss terrains contain no important mineralization, and the Pilbara granitoid-greenstone terrains contain only scattered examples of less important types of mineralization.The important deposits (e.g. Kambalda, Windarra, Agnew, Mt Keith) are all of komatiitic affinity and are best developed in the youngest greenstone belts of the eastern part of the Yilgarn Block. In particular, they are concentrated within, and adjacent to, the Norseman-Wiluna Belt, which contrasts in age, lithofacies and structural style with all other greenstone belts in the shield. It is interpreted to have been a rift zone. Within this belt the two main deposit types—the volcanic peridotite-associated and intrusive dunite-associated deposits—are concentrated into spatially separate zones. Precise controls on this heterogeneous distribution cannot be determined unequivocally from available data. One possibility is that the major volcanic peridotite-associated deposits were developed selectively in the actively subsiding axial part of the rift zone during the early extensional phase, whereas intrusive dunite-associated deposits were formed during a subsequent (less active?) stage of volcanic basin development. Distinctive sub-types (facies) of the volcanic peridotite-associated deposits form clusters that are generally within the rift zone. These may represent deposits related to discrete eruption centres, and at least part of their variation is due to relative position within extensive, topographically confined, linear flows."

Jan 1, 1984

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

The probability of detachment of quartz particles from air bubbles during bubble oscillations was investigated by means of a vibration method. Theoretical calculations of the detachment force based on the work of Nutt and Schulze for a single spherical particle show a correlation with the experimental results described. However, the forces that were determined experimentally were considerably lower than the theoretically derived values. Some of the factors which were expected to affect the probability of detachment, such as particle size, bubble size, collector concentration and vibrational acceleration, were also investigated

Dec 1, 1991

By P Shead, M A. Tuck

Both climate and methane control have been a prime concern in the development of the workings within the Deep Soft seam at Harworth Colliery. This paper describes the numerous methods employed over the past 15 years to effect control over these two major environmental pollutants at Harworth and describes a future method of working which will enable the output levels required to be achieved, whilst effecting the required level of both climatic and methane control. Firstly, the paper gives a broad historical overview of the steps taken since 1981, when production started in the Deep Soft seam at Harworth Colliery, to effect control over the main environmental pollutants in the seam. Secondly, the paper details the results of planning exercises undertaken to assess the various options with respect to panel layout, to achieve environmental control in future production districts. Finally, the recommended method of panel design to achieve the levels of production required is detailed.

Jan 7, 1997

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992

By K. C. Misra, W. Wrightson Jr.

The Lick Fork prospect shows appreciable nickel sulphide mineralization in a narrow, steeply dipping, layered sequence of metamorphosed hornblende peridotite, gahhro and hornblende gahhro, intrusive into the Pedlar Formation (charnockitic pyroxene granulite) of the Virginia Blue Ridge Complex (Precambrian). Rocks of the intrusion have equilibrated to granulite- facies metamorphism, as indicated by pervasive polygonal texture of silicate aggregates, development of biotite- and hornblende-preferred orientation, compositional equilibration of the silicate minerals, the Mg-Fe2+ (orthopyroxene-dino- pvroxene) distribution coefficients (average 0.57), (MgO + FeO + Fe20 3)/Al20 3ratios in orthopyroxenes, and Ti contents and AI(i\)/A I(\i) ratios of hornblendes. The sulphides, consisting of pyrrhotite-pentlandite (with up to 4 wt% Co)-chalcopyrite-pyrite-marcasite-violarite- bornite—mackinawite, are virtually restricted to the ultramafic unit of the intrusion and constitute 20-30% of the samples of hornblende peridotite studied. Although the basal accumulation of the sulphides may suggest magmatic segregation, sulphide- silicate textures typical of sulphide liquid immiscibilitv are not present, even in the sparsely mineralized gahbro units. On the other hand, the transgressive and relict textures are strongly suggestive of replacement of the silicate minerals by sulphides. These include chaleopyrite ± pyrrhotite ± pentlandite (violarite) ± pyrite ±magnetite veins crosscutting silicates, sulphide penetration into silicates at silicate-sulphide contact zones, rounding of silicate grains against sulphide matrix, and islands of silicate minerals (olivine, hornblende, pyroxene, biotite) in sulphide masses. Metamorphic mobilization of pre-existing sul­ phides is a possibility, but involvement of post-metamorphic, hydrothermal fluids is suggested by the following features: paucity of annealing and deformation textures in the sulphides, replacement of metamorphic and deformed silicates, lack of differential sulphide mobilization and the common occurrence of sulphides along grain boundaries and triple junctions of poly gonal silicate aggregates. The consistent association between sulphides and hydrothermal alteration products of silicates suggests that they are cogenetic. The hydrothermal fluids may have merely mobilized and concentrated the pre-existing, disseminated, magmatic sulphides, or there may have been significant addition of sulphides during this process. This question cannot be resolved unequivocally with the existing data.

Jan 1, 1984

By W. Petruk, M. J. Matos

An aplite ore from Guarda in northern Portugal, containing albite, microcline and quartz and muscovite gangue was studied to identify conditions for extracting the feldspar minerals. The large amounts of quantitative mineralogical data needed to evaluate grinding behaviour were provided by automated image analysis. The images were acquired on polished surfaces by measuring back-scattered electron signals produced with a microprobe. Minerals were identified from X-ray spectra and discriminated by grey level and element-characteristic X-rays. The quantities and size distributions of the minerals were determined by measuring thin sections of unbroken ore to predict the grind required to liberate the feldspars. The ore was then ground to -1.7 mm, polished sections were prepared from sieved fractions and the quantities of mineral species and apparent total liberation were determined by analysis. The predicted and measured liberations were compared and the grinding behaviour of the ore interpreted. In an appended correction, the correct version of Equation 1 is represented and Tables 3 and 6 are revised to consider all size fractions, including those coarser than 300 micrometres, in calculating the total liberation from King's fractional liberation

Jun 18, 1905