Search Documents

By Li Maolin, Cui Rui, Wang Guanghui

"As the stirrer speed directly affects the motion of grinding media, and hence the interactions with material particles to be ground, the rotation speed of a stirred mill is well recognized as one of the most important factors affecting the grinding performance. In this work, the effect of stirrer speed on grinding performance in terms of grinding rate and grinding energy efficiency was quantitatively investigated. Batch wet grinding tests of quartz powder at different stirrer speeds were performed, using a self-made horizontal stirred mill with alumina balls as grinding media. Grinding time, operating power and the sizes of ground product were recorded to analyse the grinding performance. The test results showed that grinding processes followed the first order grinding kinetics. The grinding rate constant increased with the increasing stirrer speed. Based on the grinding kinetics, the grinding energy equation was established. The energy utilization coefficient in the energy equation can be used as an indicator of energy efficiency. The energy efficiency decreased with the increasing stirrer speed. Quantitatively, with the stirrer tip speed increasing from 4.25m/s to 9.35m/s, the grinding rate constant was improved by 441.47%, whereas the energy utilization coefficient was decreased by 39.35%. The grinding rate constant and energy utilization coefficient can be used to evaluate the grinding performance when the grinding conditions need to be adjusted. The adjustment of grinding conditons would be optimal when grinding rate get significant improved with little decrease of energy efficiency."

Jan 1, 2014

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By J. Shibata

The behavior in electric field of fine particles present in aqueous solution was measured in order to apply to the classification of fine particles. The sample particles used are spherical polystyrene particles with the average diameter of 0.03 µm, 0.1 µm, 1.0 µm, 4.3 µm and 9.6 µm. Electrophoretic mobility and zeta potential of various particles are measured by an instrument based on the principle of the laser Doppler effect. The influence of temperature, electrolyte concentration on the electro-phoretic mobility was investigated for various polystyrene particles. The electrophoretic mobility increases with increasing pH and temperature of suspensions. The measured electrophoretic mobilities are different from electrolyte concentration and particle size. The electrophoretic retardation effect and relaxation effect are considered to explain the behavior of fine particles in electric field by applying the electro kinetic theory of Wiersema et al. For all particle size, the electrophoretic mobility decreases rapidly in high concentration of KNO3 such as 0.1 mol/dm3due to the compression of electric double layer The forces acting the particles in electric field are considered to be electrical force, friction force and some other forces like relaxation effect and electrophoretic retardation effect which appear in ionic behavior. It is considered that the particle moving velocity depends on the particle size. When the particle size is less than 1µm, the velocity increases with increasing the particle size. On the oth-er hand, the velocity deceases with increasing in particle size, when the particle size is larger than 1µm. This phenomenon is considered to be interesting from the viewpoint of classification for fine particles. We found that the electrophoretic mobility of 1.0µm particles is larger than that of 0.1µm particles, and that it is possible to classify fine particles by using the difference of electrophoretic mobility by many experimental results. The phenomena can be explained by the forces acting the fine particles in the electric field. We can apply the behavior to classification of fine particles.

Jan 1, 2014

By Thomas Mütze, Anja Hirte, Ursx Peuker, Thomas Kuhn

"The comminution behavior of two ferromanganese nodules samples of the equatorial northeast Pacific has been examined as a basis for the separation of two kinds of metal-rich layers. Those layers were finely grown together during nodule formation and are one reason that the exploration of deep-sea minerals calls for the development of new mineral processing concepts. Therefore fundamental analyses of the fracture behavior have been made under compressive and impact stress. Further experiments took focus on the crushing behavior in a jaw crusher and a small scale impact crusher as well as the milling behavior in a dry vibrating mill, a wet planetary ball mill, and a wet agitated ball mill. The comminuted products were characterized by PSD, particle shape, particle density, and porosity. The experiments show a low stress resistance of the ferromanganese nodules. Compared to compressive stress, impact stress turned out to be the more effective for crushing. Both samples showed no significant difference in the comminution behaviour which makes differing mechanical treatments unnecessary. In both cases particle sizes below 1 µm were achieved by wet grinding. This particle size is necessary to separate the two kinds of metal-rich layers which is part of continuative studies."

Jan 1, 2014

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By Weiguo Xie, Malcolm Powell, Lian Liu, Ping Yu

"In order to develop a common mathematical and simulation platform for tumbling mills, a review of existing mechanistic models was made identifying the key aspects of grinding and slurry transport which are common to all tumbling mills. A mill model structure has been developed for all types of tumbling mills based on the population balance framework by incorporating breakage characteristics, slurry and solids transport, product classification and discharge, and energy consumption. A size-dependant breakage model developed by the JKMRC is applied. Transport is separated from breakage events and treated as a main sub-model in the new model structure. The model structure is based on dynamic time-stepping technique to enable dynamic simulation capability for non-steady-state simulation and control modelling. It is envisaged that the new model will cover a full range of milling conditions. It should enable a smooth transition between different mill types, such as from AG (Autogenous Grinding) to SAG to ball mill. The dynamic mill model structure developed here is the first step towards mechanistic modelling of grinding mills and provides great potential for the optimization of the comminution process."

Jan 1, 2014

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By Xiaodong Jia, Richard A. Williams

"The packing of particles is a fundamental property of a material or system made up of particulates because it underlies many other physical properties of that material or system. Despite being ubiquitous, particle packing has not been an easy subject to study either experimentally or theoretically, except for a few regular shapes.This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. Figure 1 shows a few examples that are relevant to the mining and mineral industry.The ability to predict packing structure of real particle shapes and to compute directly some structuredependent physical properties (such as liquid permeability, mechanical strength/stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.The mining and mineral engineering industries are well placed to exploit this advance in digital packing and simulation since they deal primarily with asymmetric and complex particulate mixtures. In the future we expect to see a number of developments in this area including:Algorithms that can optimise packing to achieve user-defined propertiesA more rational approach to determining flowability of complex powdersUse of these more realistic packing algorithms linked to blast and crusher design"

Jan 1, 2003

By Arkady Senchenko, Yuri G. Seredkin, Alexander Aksenov

"This paper describes the development of efficient technology for the treatment of complex ores containing gold and copper as major valuable components, where silver is present as well. Copper is mostly represented by oxidized minerals in these ores; however, copper sulfides are also present. Gold is present in its free form and in associations with oxidized and sulfide minerals; silver usually accompanies gold. Complex composition of the ore requires complex solutions for their treatment. The results of searching for the techniques to recover valuable components are described in this paper. Gravity methods allow for free gold recovery, flotation methods allow one to recover major part of copper and precious metals in associations; and in the result of leaching process additional amount of copper, gold and silver is reported to solution. Combining all these methods help achieving high levels of valuable components recovery. When implementing a combined technological flowsheet about 80 % of copper goes to concentrates from gravity and flotation of sulfide and oxidized copper minerals; and sulfuric acid leaching allows increasing total copper recovery up to 90 % and higher. Major part of precious metals (up to 90 % of gold and 80 % of silver) is recovered to these concentrates, and after hydrometallurgical treatment it is possible to increase gold recovery up to 96 %, silver recovery - up to 90 %. The suggested technology helps solving the problem of precious metals recovery from complex gold-copper ores, and allows treatment of the ore with different proportion of sulfide and oxidized minerals, and at different valuable components grade."

Jan 1, 2014

By Xiaoping Xu, Tiansong Dong, Guosheng Wang

"Jianfengpo tin ore is located in Jiangxi Province, China. The cassiterite is fine and dispersed. It is hard to separate marmatite from a variety of sulfide minerals. Because the iron-containing sulfide minerals including pyrrhotite, pyrite and chalcopyrite are detrimental to the improvement of the grade of zinc concentrate. Besides, the presence of the iron oxides and ferro-carbonate minerals results in the difficult beneficiation of tin. Therefore, Jianfengpo tin ore is a kind of refractory cassiterite polymetallic sulfide ore. According to the properties of Jianfengpo tin ore, the technology process of "Sulphide ore preflotation-Bulk flotation of sulphur and zinc-Separation of sulphur and zinc -Magnetic separation-Gravity concentration" was developed to recover the valuable materials including marmatite, pyrite, magnetite, cassiterite and indium comprehensively. For the feed ore containing 0.87% Sn and 0.70% Zn, a zinc concentrate of 44.56% Zn with a recovery of 69.10%, a high-grade tin concentrate of 54.38% Sn with a recovery of 53.03% and a low-grade tin concentrate of 6.54% Sn with a recovery of 1.25% can be achieved in the batch flotation tests. In the industrial tests, for the feeding which contains 0.55% Sn and 0.65% Zn, the tin concentrate of 49.10% Sn with a recovery of 48.52% as well as the zinc concentrate of 45.11% Zn with a recovery of 60.10% can be produced. Thus some pyrite and magnetite concentrate are recovered as well. So Zinc, tin, sulphur and iron ores are recovered effectively by the technology."

Jan 1, 2014

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014