Search Documents

By M. Saghaeian, R. Hejazi, L. Hosseini, M. Zare

Difference between plant feed specifications in practice and design feed is a problem that most of processing plants face during operating and commissioning. This topic has led to inappropriate operating and necessitates repeating the basic tests on new feed. Gol-E-Gohar fourth concentrate line with a capacity of 2 MTPY, located in Kerman province, is the first iron concentrate plant in Iran in which High Pressure Grinding Roll (HPGR) technology has been applied. Plant&apos;s feed consists of 30% AG mills pebbles of lines 1-3 and 70% run of mine crushed ore whose Fe=51%, Fe/FeO=2.5, S=1.7% and work index=15 kWh/t. Desired concentrate has Fe>68% and S<0.7%. After the plant construction and operation commencement, providing design feed was not possible due to the crushing unit`s not being complete, therefore the plant was fed by AG mills pebbles. For predicting optimal conditions of the plant and investigating the possibility of improving the current concentrate specifications, sampling from the new feed and laboratory and pilot tests was performed again. Studies showed that new feed has Fe=41%, Fe/FeO=3.5, work index=17 kWh/t. Results of laboratory tests with Davis tube device and pilot tests run using magnetic separators with simulating the plant`s circuit showed that with current feed, achievable recovery in industrial scale would be 75.52% which compared to plant&apos;s recovery in studied period (75.94%) shows that plant operated in optimal conditions. To improve the current concentrate specifications (Fe=66%, S=1.03%, Ferec=75.94%) and for achieving desired concentrate, samples were reground to four fractions with k100= 300, 212, 100, 45 and Davis tube tests were performed on each of the samples separately. Results showed that the fraction whose k100=212 µm or k80=200 µm has respective Fe and S grades of 68.27% and 0.681% which are consistent with the desired concentrate.

Jan 1, 2014

By S. Kondratiev

Mechanism of the action of nonpolar physically adsorbed reactants in froth flotation is under discussion in the paper. It is shown that their basic influence on flotation includes removing of the kinetics restrictions of the flotation complex formation. Experimental data and practical evidence reported in the paper sustain the proposed mechanism. There are discussed potential dependence of the kinetics of dixanthogen formation on platinum and its influence on the induction time (IT).

Sep 1, 2012

By M. Panayotova

Most of the quantity of the water soluble xanthates, used in mineral flotation, is consumed in the process. However, the residue amounts are water contaminants downstream the mineral processing operations and can be toxic to aquatic biota at concentrations of 1 mg/L. In order to be able to discharge water from tailing ponds to natural water bodies the concentration of xanthates has to be decreased. The present paper studies the uptake of potassium ethyl xanthate by directly modified with copper and lead ions natural zeolitic rock, without passing through zeolite transformation into homoionic form. Modified zeolite exhibits high, comparable with powdered activated carbon of chemical purity grade, capacity to remove potassium ethyl xanthate from model wastewater, with pH in the range of 7?9 and pollutant concentration in the range of 10-150 mg/L. The pollutant immobilization is fast. Both Cu and Pb modified zeolite behave as selective with respect to xanthate in the model wastewater, and Cu-modified zeolite possesses higher selectivity. The equilibrium is best described by the Freundlich equation. Keywords: xanthate, wastewater, modified zeolite

Sep 1, 2012

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

"There are a variety of methods suitable to analyse elemental and mineralogical contents of rock drill core samples. Current demands are on fast exploration and objective analysis of ore samples. This paper proposes a combination of Laser-Induced Fluorescence (LIF) and image processing, entitled LIF-imaging, as a potential method for automated mineral analysis of the drill core samples. It is shown that LIF-imaging can produce a mineral map of the fluorescent minerals existing on the surface of the drill core samples. The test cases are drill core samples from a Ni-Cu mine situated in Kevitsa, Finland. The main prerequisite of LIF-imaging technique is a reference data, linking colours to the minerals. This study describes the calibration of LIF-imaging technique using precise but slow Raman spectroscopy. Using regularized logistic regression, a model is obtained that classifies the minerals based on their emitted fluorescent colours in the digital images. The abundance of each mineral group is estimated by pixel counting. The results are compared with X-Ray Diffraction laboratory assays performed on the same samples. The results show that the interpretation of the fluorescent minerals through LIF images corresponds to the XRD results. Furthermore, the utilization of the logistic regression to interpret the existing fluorescent minerals greatly improves the technique."

Jan 1, 2014

By Mojtaba Ghorbannezhad, Abbas Sam, Soroush Arabzadeh

One of the dewatering methods in mineral processing plant is filtration system. Disk filters are included the porous surface with pressure drop on both sides, Water in the pulp passes through the surface and solid particles remain as a cake on it. Wet concentrate production of magnetite processing plant at Golgohar Mining and Industrial Company with solid tonnage of 160 ton per hour and 49% solid amount contains 166 m3/h of water. In the present study, in addition to studying disc filter performance, the effective parameters on cake moisture were studied using Vacuum Bottom-Feed Leaf method (in the laboratory scale). Optimization was performed using the Taguchi method. The results showed that the cake moisture is reduced by increasing particle size and solid percentage (because of specific resistivity reduction), while the rate of cake formation and its thickness are increased. Also, it was found that by increasing pressure, the cake moisture is reduced and cake formation rate and its thickness are increased. In this study, the effect of fabric texture was also examined. Lowest cake moisture was obtained in condition of using compressed plain fabric with mono-multi filament fibres, pressure at 75kPa, solid percentage of 65 to 70, particle size (D80) equivalent to 123µm and disk rotation speed of 1.25 rpm.

Jan 1, 2014

By A. D. Ramirez, L. E. Gutierrez, M. A. Garces

"Scarcity of freshwater in mining operations in arid zones in different parts of the world has led to the mining companies to think about using seawater as an alternative source in mineral processing operations. Examples of this situation are Minera Centinela (AMSA) and Minera Sierra Gorda (KGHM), both plants located in northern Chile. Previous studies showed that molybdenite flotation is depressed at high pH values in seawater as a result of the action of hydroxy-complexes of magnesium and calcium that attach to the faces of the molybdenite particles, reducing its hydrophobicity and as a result flotation recovery. In this work, a study of the interactions between molybdenite and kaolinite is presented. The effect of sodium hexametaphosphate (SHMP) dispersant on the recovery of molybdenite in the presence of kaolinite is studied in different aqueous media and it is correlated with induction time data. The results allow to conclude that kaolinite has a stronger depressing effect on molybdenite in seawater compared to its effect in freshwater. Magnesium and calcium are the cations that have the strongest effect in enhancing the interactions between molybdenite and kaolinite. SHMP reduces the negative effect of kaolinite on the floatability of molybdenite both in seawater and freshwater. The induction time data correlate well with the micro-flotation results.INTRODUCTION The need for water in mining processes in arid and semi-arid zones has led to the search for new alternatives for this resource, among which seawater has gained an important space. In Chile, most of the mining operations are located in the northern part of the country, an area that has limited availability of freshwater for the processing of copper and molybdenum sulfides (Castro and Laskowski, 2011, Castro et al., 2012 a). Seawater is an aqueous solution with high concentrations of ions such as Na+, K+, Mg2+, Ca2+, So42-, Cl-, and other less concentrated species which generate important effects in the flotation process as they modify the properties of the solid/liquid, and liquid/gas interfaces, and also increase the consumption of some important reagents used to depress pyrite such as lime. It has also been proposed that flotation of copper sulfides is negatively affected in seawater because of the reduction of oxygen solubility compared to freshwater (Millero et al., 2002; Duan and Sun, 2003). In contrast, it has been shown that the presence of ions in solution in the process of flotation of natural hydrophobic resources improve recovery as result of the compression of the electric double layer (Laskowski, 1974; Klassen and Mokrousov, 1963, Laskowski and Castro, 2008."

Jan 1, 2018

By R. C. Miranda

Artificial vision systems are increasingly used to assist humans to perform different tasks in different areas. These systems are able to recognize patterns in complex images, which can provide multiple data. Currently, vision systems are used in both; monitoring traffic - which uses radars for vehicular plate recognition- as in metallurgical and food industries for strict quality inspections. Their use in mining occurs in measuring the speed of froth over the lip of a cell, in determining the shape and size of pellets, in obtaining from the tendency of mineral content and as a replacement for laboratory analysis of particle size. With this advanced tool, it is possible to achieve significant improvements in quality, productivity, and especially in reducing costs in pelletizing plant of iron ore. The objective of this paper is to contemplate the current situation of image analysis in the pelleting plants and glimpse at the potential applications that are being developed. This paper also presents the conception and implementation of an automatic control system of the pellets size distribution applied on a pelletizing plant of iron ore. The article demonstrates the strategy used for measuring the size distribution of the iron ore pellets, based on image analysis and the strategy implemented on advanced process control, which shows substantial gain on plant performance.

Sep 1, 2012

By Vladimir Vigdergauz

"Electrochemical studies of metal sulfides in connection with their floatability are discussed. According Frumkin, sorption of electroneutral organic substances has a maximum near the potential of zero charge. This idea initiated attempts of application of electrochemical methods for the controlling of organic collector sorption and mineral flotation. The lecture reviews results of electrochemical studies of the processes taking place during sulfide flotation: redox-state of mineral surfaces and xanthate solutions, xanthate sorption and hydrophobic layer composition, surface wettability and flotation recovery of sulfide minerals. Redox-transitions of minerals, transport of ions and charging of mineral surfaces, electroreduction of dissolved oxygen and accompanying processes of oxidation of minerals and reagents-collectors, - all these matters became the subjects of detailed research. Cyclic voltammetry, rotating disk electrodes, spectro-electrochemical techniques and other modern experimental methods now routinely accompany studies of mineral processing. Relatively new electroanalytical techniques like the voltammetry of mineral particles immobilised on electrodes using polymeric binders have become extremely useful for studying weakly conductive minerals and dispersed flotation products. Full discussion of electrochemical studies of metal sulfides in relation to mineral processing must include bioelectrochemistry and electrocatalysis which open exceptional possibilities for selective leaching of gold and non-ferrous metals. At this time, the paper focuses on the sulfide flotation as a potential-dependent process; the problem of oxygen and its influence on the sulfide flotation; the electrochemical aspects of xanthate oxidation and sorption; theory of suspended electrodes as applied to the mineral slurries and experimental study of the effect of electrochemical pretreatment of flotation pulps."

Jan 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

High flotation of iron sulfide minerals at high pH values in copper ores is mainly due to the activation of these minerals by copper species dissolved from copper sulfide minerals during grinding. Several methods have been tested to reduce this copper activation during grinding and therefore to depress iron sulfide flotation. They include grinding the minerals at high pH values or with a less reactive medium such as high chrome, and addition of a thiol collector or copper complexant during grinding. The efficacy of these methods in the flotation of a copper ore was tested against more common methods of depression of iron sulfide flotation. The mechanism of iron sulfide depression in these methods was also investigated.

Jan 1, 2014

By A. V. Bogdanovich, S. A. Urnysheva

"Gravity and X-ray luminescent separation methods are generally used in processing of diamond ores. X-ray luminescent separators are applied for separation of diamonds from feed ore size fractions from 100 to 10-15 mm size and for final treatment of gravity concentrates over 1 mm size. Gravity separation machines used for diamond ores separation are heavy medium cyclones and pneumatic jigs. One of the most important parameters, to a large extent affecting diamonds recovery from ore, as well as processing costs and specific energy costs, is size of dumped final tailings. That was exactly the purpose of the studies, the results of which are described in this paper. The studies performed on different ores showed that in order to achieve high recovery results, it is necessary to dump heavy medium separation tailings below 3 mm size. Separation of final tailings of -6+1 mm size by jigging is also possible. However, with a view to exclude extra diamond losses, it is necessary to maintain jigging concentrate yield approximately at 25% from starting feed, with its subsequent cleaning in heavy medium cyclones. In addition to that, it is necessary to separate 20-25% of middling with diamonds content at feed ore level and subject it to grinding. This will complicate flow sheet, but reduce load on heavy medium cyclones. In order to develop optimal flow sheet for gravity concentration of a specific diamond ore, large-scale investigations are required, including technical-and-economic assessment of separation alternatives. INTRODUCTION In processing of diamond ores, gravity and X-ray luminescent separation methods are generally used. It is common practice to apply X-ray luminescent separators for separation of diamonds from feed ore size fractions from 50 (100) to 20 (10) mm size and for final treatment of gravity concentrates over 1 mm size. With that, X-ray luminescent separation tailings larger than 3-6 mm size are reground and delivered to gravity concentration processing stage. Middling products circulation volumes are large, not infrequently necessitating decrease in concentrating plants capacity, especially with mining in deep workings of deposits, where ore strength is higher (Goryachev, 2010; Vaginov, 2000; William, 1988). Diamond ores preparation before processing is accomplished by means of roll-screw crushers and autogenous grinding mills, minimizing probability of free diamonds damage in liberation from barren rock. In re-crushing of size fractions that are “difficult” in autogenous grinding, high pressure grinding rollers are applied (Burchardt, 2014; Fedotov, 2011a, 2006b)."

Jan 1, 2018

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

By Bruno Michaux, Markus Reuter, Martin Rudolph

"It is relatively well-established in the literature that the flotation of calcium minerals using fatty acids as collector is very sensitive to the process water composition. In particular, hard waters have often been reported to strongly reduce the target mineral recoveries due to the formation of insoluble compounds such as calcium and / or magnesium dioleate, thus reducing the amount of collector available for adsorption onto the mineral surface. In this study, the flotation of a fluorite pre-concentrate was performed with tall oil, an industrial collector essentially containing fatty acids. The tests were performed in a variety of synthetic waters to simulate multiple degrees of water hardness, and to differentiate the role of magnesium and calcium ions on the flotation performance. The flotation tests revealed that, under the studied conditions, a significant difference between flotation in calcium-rich and magnesium-rich waters was observed, suggesting strong ion-specific effects in the system. Specifically, calcium-rich waters slightly improved the fluorite recovery, whereas magnesium-rich waters caused a decrease in recovery by as much as 20%. This paper is focused on the flotation kinetics aspect of the system. This approach highlighted the interesting finding that calcium ions did not simply increase the fluorite recovery, but also significantly increased its flotation kinetics. The magnesium ions, on the other hand, had the exact opposite effect.INTRODUCTIONAs the mining industry is facing an increasing number of issues related to its fresh water consumption, the idea of using alternative water sources for mineral beneficiation is gaining significant momentum. As a result, a proper understanding of the role of water chemistry in flotation is becoming more and more urgent, leading to an increasing number of studies on this topic."

Jan 1, 2018

By Marko Hilden

"A stochastic model of mineral texture is discussed and used to demonstrate that grain association within the intact texture has a significant effect on the liberation characteristics of breakage products. The majority of previous models have simulated texture and liberation of binary systems. This new model is able to simulate complex multi-component (multi-mineral) aggregate textures and their breakage products. Grain size distributions can be defined for each of several minerals. Mineral-mineral associations can be controlled by inserting mineral grains within grains of another mineral. Repeated Monte Carlo sampling of the aggregate is used and the liberation properties of the fragments are calculated. These are analysed to generate data in a similar form as reported by mineral liberation analysis systems, including density distributions, liberation distributions, and particle class distributions. Simulations results are presented where the model has been fitted to complex sulphide ores with four minerals. Comparison of the simulated particles and experimental data show that the model is able to reproduce similar particle class distributions as measured by QEMSCAN. The texture of real complex ores can be simulated and fitted to conventional mineral liberation analysis data. The model should provide a useful and practical means of modelling the effects of mineral texture on separation processes and in geometallurgical models."

Jan 1, 2014