Search Documents

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By Vladimir G. Kochnev

An innovative AG and SAG technology aimed to be applied in grinding of ores and in the production of construction materials is described. A novel design of a cantilever-type mill capable to operate in autogenous, semi-autogenous and ball grinding mode ensures easy delivery and installation even in remote areas, and low capital and operating costs. Results of the tests of the new heel-shaped liners performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation are reported. The approach includes also a novel discharge grid design and a technique of treating the material of critical size. These innovations make grinding in AG and SAG mills dramatically more effective, with an increase in the throughput rate and a reduction in power consumption ranging from 1.5 to 2 times.

Jan 1, 2003

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By C. Dorfling, S. Bradshaw, J. Eksteen, M. Khesa, C. A. Snyders

Titaniferous ores serve as a major feedstock for the production of a white titanium dioxide pigment, a titanium metal and several other titanium-based products. Such ores exist mainly as heavy mineral sands. Ilmenite is upgraded to intermediate products namely synthetic rutile and titania slag through the synthetic rutile route and the reductive smelting route respectively. Tronox KwaZulu Natal Sands (Pty) Ltd recovers high titania slag via the reductive smelting process while slag is used as a feedstock to the pigment industry and furnace dust from the gas cleaning plant is disposed as waste. Previous investigations have shown that such furnace dust can contain significant amount of titanium-bearing minerals. This study looks at the characteristics of the furnace dust obtained from Tronox KwaZulu Natal Sands and investigates a possible high temperature recovery route in detail. The furnace dust was examined by using x-ray fluorescence, x-ray diffraction, microscopy and laser-diffraction size analyses. The characterization work showed that the furnace dust was rich in titanium and iron, containing 49.4 wt% ??????2 and 29.5 wt% ????2??3. These oxides were associated with Si, Mn, K, and Al oxides as impurities. A Carbolite® vertical tube furnace was used to investigate the extent of formation of titania slag and metallic iron on a laboratory scale at 1500°C, 1600°C and 1650°C. The laboratory reduction tests revealed that the slag samples with an equivalent titanium dioxide content ranging from 70.9 -76.9 wt% at 1600°C and 1650°C could be obtained. The Fe content of the metallic iron samples produced ranged between 93.0 and 97.1 wt%. The experimental results were found to be in relatively good agreement with the FactSage simulations, both of which demonstrated the potential of producing a titania slag and a metallic iron from the furnace dust.

Jan 1, 2018

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By Andries Van Wyk, Steven Bradshaw, Guven Akdogan, Jacques Eksteen, Cornelius Snyders, Cleophace Mpinga

"In order to exploit lower grade and complex platinum group metal resources, cheaper and more efficient alternatives to the conventional mill-float-smelt-refine route are being sought, particularly for resources’ in areas that are water-scarce and where electrification is costly and problematic. Leaching with cyanide is a promising process option and although recoveries are lower than in the conventional process routes, progress into the understanding of cyanide leaching of PGM containing ore and concentrate has been made. Research regarding the feasibility of upgrading the pregnant PGM leach solution using activated carbon has, however, been lacking and hence forms the focus of this paper. Bottle roll adsorption tests for dilute PGM solutions (0.15ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) onto granular activated carbon showed high rates within the first 60 minutes (giving more than 90% recovery of precious metals). Comparison of the Pt isotherm to Au isotherms from literature indicated a similar loading capacity, while that of Pd was found to be significantly lower. The effects of solution pH, temperature, base metal concentration, free cyanide concentration, thiocyanate concentration, initial PGM concentration and activated carbon concentration were investigated and are discussed. Elution of the Pt and Pd, with the AARL elution process, was found to be effective with recoveries of 95% after 5 bed volumes of eluant at the optimum pre-treatment concentrations and a temperature of 80°C. Temperature, NaCN and NaOH pre-treatment concentration and the ionic strength of the eluant were found to be the most important factors affecting elution while base metals concentration, acid-pre-treatment, carbon loading and thiocyanate concentrations to a lesser extent. Simplified combined flow sheets are suggested and the corresponding mass balances are compared."

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By C. P. Lowes

"The REFLUX™ Classifier (RC™) consists of a fluidized bed housing, with a system of parallel inclined channels above. This system performs a simultaneous gravity separation and desliming of the feed material, utilising the inclined channels in order to retain the relatively fine dense particles. These particles promote the formation of an autogenous dense medium within the fluidized bed. Relatively large, low density particles are displaced from the fluidized bed and conveyed upwards through the inclined channels reporting to the overflow with other finer particles. Given the hydrodynamic role of both the particle size and density in determining the particle transport through a water based suspension, all gravity separators operate over a limited size range. In the case of the REFLUX™ Classifier, efficient separations can be produced across a very broad size range, from nearly 10 mm down to 10 m, however, for a given application the size range is much more limited. This study was concerned with the processing of dense minerals over a broad size range, and the need for multistage processing. Here the overflow from the first stage cascades to the second stage, incorporating coarse gangue rejection. This approach is shown to deliver remarkably high grades and recovery.INTRODUCTION The performance of the REFLUXTM Classifier (RC™) in beneficiating fine coal is well documented (Galvin, 2012). Although the technology can be applied to relatively fine particles below 0.1 mm, or coarser particles below 2.0 mm or even 8.0 mm (Galvin et al., 2010), in each case the technology is applicable to limited particle size ranges. In coal preparation, the most common size range is 0.25 to 2.0 mm, covering an eight-fold range in the particle diameter. Coal has a relatively low density, typically below 1600 kg/m3, with a significant portion below 1400 kg/m3. In water, the buoyant density difference (~ 400 kg/m3) is therefore low compared to that of gangue minerals (1600 kg/m3) by a factor of 4, enhancing the potential for separation. Thus, in coal preparation, the technology can be applied over a commensurately broader size range, typically up to eight-fold."

Jan 1, 2018