Search Documents

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By Ross D. Lawrence

"IntroductionOne of the methods used when applying the Market Approach to the valuation of a mineral exploration property is known as the Joint Venture Terms Method. The method is particularly useful for the valuation of early-stage exploration properties. Unfortunately, valuators are sometimes imprecise in distinguishing between joint ventures and other types of transactions.At VALMIN '94, Bob Appleyard1 proposed that, if one ignores the time value of money and the probability that the expenditure commitment would be completed, the formula to calculate the value ($V) of a property owned by Party B at the time of the deal would be:$V =$Ex (100-1%)/1% (Formula I)Where $V is the value of the property2Where $E is the expenditure commitment by Party A, andWhere 1% is the percentage property interest to be earned by party A.At PACRIM '99, Mike Lawrence and Graham Dewar3 referred to this method and suggested that there was an ambiguity in the formula proposed by Appleyard in 1994. Mike Lawrence referred to this problem again at VALMIN '014•Lawrence & Dewar suggested that the formulashould be:$V100% =($Ell%) x 100 (Formula 2)Where $V 100% is the value of the entire property,Where $E is the expenditure commitment by Party B, andWhere 1% is the percentage property interest to be earned by Party B.Subsequently, there has been considerable discussion in the AuslMM Bulletin5. In my view, this discussion has touched on a number of useful points, but generally has overlooked one essential element needed for an understanding of the correct application of the N Terms method. That essential element is to understand that there is a material difference between (1) entering into a joint venture arrangement and (2) the purchase of an interest in a property."

Jan 1, 2003

By J. F. Henderson

Stable mining operations commenced in the Northwest Territories in 1933. Pitchblende from Great Bear lake and gold from the Yellowknife district are the main minerals produced. The value of pitchblende products produced from 1933 to 1941 was nearly $6; 000; 000; data on subsequent production are not available. The first gold was produced from the Con mine at Yellowknife in 1938. Other properties that later came into production include the Negus; Slave Lake; Thompson Lundmark; and Ptarmigan mines. The annual gold production reached $3; 862; 000 in 1942 but due to the war and consequent labour shortage fell to $333; 218 in 1945. The only producing mines at present (May; 1947) are the Con and Negus; but several promising properties are under development; including that of Giant Yellowknife Gold Mines where large tonnages of ore are being blocked out. With the reopening of former producing mines and new production from properties now being developed; gold production should rapidly increase and exceed its former peak within the next few years.

Jan 1, 1954

By Andre L. Du Preez

Global mine hoisting regulations require safety fall arrest systems to be installed on vertical conveyance systems capable of safely decelerating and supporting a fully loaded conveyance in the event of a rope severance. Most current arresting systems are incapable of producing controlled safe deceleration rates. Although safety ?dogs? achieve marginally acceptable results on wooden guides, difficulties arise in achieving safe deceleration performance requirement where safety arrest systems operate on steel shaft guides. Previously, arresting systems capable of operating with steel guides have been incapable of producing controlled deceleration rates during the arresting of free-falling conveyances. Most are ?instanton? systems, whereby an occupant inside a conveyance being arrested would be subjected to unacceptably high deceleration forces. This paper briefly highlights the background to the selection process of Rio Tinto?s Technical Staff of a suitable Mine Conveyance Safety Fall Arrest System for #1 Shaft at Rio Tinto Oyu Tolgoi Mine, Mongolia. It also describes the Drop Test and Free Fall Test procedure and the results leading to the acceptance of the Horne Group Levelok® Emergency Braking Technology for the Oyu Tolgoi #1 Shaft in Mongolia. The paper highlights Rio Tinto?s primary objective for the selection of this advanced technology on their primary production shaft cage system as an emergency safety catch braking system combined as an advance hydraulic chairing system. It describes the design and operational parameters and the 'Fail to Safe' interfacing with current automated mine hoist systems.

Aug 1, 2013

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005

By E. Goodwin

The mechanics of formation of wear-metal suspensions in lubricants is discussed, along with the relationship of the concentration of the metals and other particles to the wear of lubricated machinery parts. The importance of particle and suspension analysis of used lubricants in a preventative maintenance program is stressed, in particular with regard to mobile equipment in a mining operation.

Jan 1, 1978

By Micheal Mayhew

"This presentation will provide information and facts on the drilling and blasting within a frozen shaft using a full face methodology. The Author will briefly discuss the history of the sinking of a frozen shaft in Saskatchewan, the challenges faced, and the solutions delivered. The case study will include a discussion describing the series of events that led to the decision to adopt a full face blasting methodology. The case study will describe key elements such as the drilling pattern, hole size and depth, explosive products and blast vibration monitoring systems. INTRODUCTION During the shaft sinking process at a project in Saskatchewan, it was recommended that a drill & blast benching method be utilized. Following an evaluation of the site, the geological conditions proved amenable to a ground freezing system that would stabilize the rock formations and prevent inflows of water into the shaft (Table 1).The shaft sinking process required that the ground surrounding the proposed shaft be frozen by drilling several near vertical freeze holes radially at a specified distance from the edge of the proposed shaft excavation. This would allow for the circulation of a chilled brine solution down the freeze holes. The circulation is achieved by means of stainless steel pipes encased within each other to provide a delivery and return conduit for the brine (Figure 1). As a result of this periphery freezing, the ground within the shaft excavation is also predominately frozen.The finished internal diameter of the shaft was 5.5 meters with varying overall excavation diameters to facilitate different liner designs used for various rock formations. For the most part, the fully unsupported/unfinished excavated diameter of the shaft varied from 6.9 meters to 8.5 meters depending on the zone excavated. The challenge was that the proposed drill and blast excavation method posed a significant risk due to the potential to damage the freeze wall and pipes during blasting. The decision was made to commence the excavation through mechanical excavation (i.e. chip and cut) methods then change to a drill and blast method utilizing a split benching design. Through this process, the team encountered five main challenges: 1. Sub-horizontal geological structures and slips that affected blasting performance and sometimes resulted in a sloping surface to the top of the bench; 2. Confined working area for the crews and equipment due to a limited work area as a result of utilizing the split (half) bench drill and blast methodology; 3. Mechanical chipping and cutting of the one-meter buffer zone to the final shaft diameter; 4. Crews working on extremely slippery uneven frozen rock and ice surfaces, which affected safety and efficiency; 5. Establishing a blast vibration monitoring system to determine if the drilling and blasting of the full shaft excavation diameter were acceptable."

Jan 1, 2019

By Sh. Karimidorabati

In the construction industry, project changes constitute a major cause of delay, disruption, cost increases, poor quality and unsatisfying performance. They are also known as a main factor of litigation between the owners and constructors. Construction projects are essentially process-based, and with the critical role of Information Technology (IT) in this industry, projects, especially mega projects, are being managed remotely. The volume of data and documents, such as Requests For Information (RFIs), different types of Change Requests (CRs) and Project Change Notices (PCNs), being transferred and exchanged amongst the stakeholders of a project is considerable. The circulation of these documents amongst project stakeholders still heavily relies on two methods or levels for management of change process; Conventional (fully paper-based, Faxes, Snail mails) and Electronic or semi-automated (Email, Internet, PDF files). These two methods are dependent on human discipline to follow specified processes which often break down because of human nature. This creates serious compliance problems. It is hypothesized here that fully that automated process-based management of change can lead to better compliance, more efficient management of change, and reduction of time and cost of data exchange. An approach of doing this is presented in this paper. Ultimately, its impact should improve project performance. Conclusions are presented on time savings and improved compliance.

Aug 1, 2013

By Matthew Blecha

The Tribag copper deposit is one of the rare examples of mineralized breccias in the Canadian Shield. The breccia is a pipe-like body, and consists of granitic, diabasic and volcanic fragments embedded in a vuggy, quartz-carbonate matrix. The mineralization is essentially chalcopyrite and pyrite, with minor molybdenite, sphalerite, galena and other sulphides. The main ore zone is saddle-like in shape, and is enveloped in a zone of chloritization, sericitization and clay-mineral alteration. It is suggested that the breccia is of the diatreme type. Introduction T HIS paper is based on eighteen months of field work, including surface and underground geological mapping and core logging, and on the survey of relevant literature. No significant amount of laboratory work has been done as yet. Location and Access The Tribag Batchawana property is located 40 miles north of Sault Ste. Marie, Ontario, about 10 miles east of Lake Superior. A 17-mile, all-weather road connects the property to the Trans-Canada highway to the south, and 4 miles of a 12-mile road remain to be completed to link it to the Algoma Central Railway to the northeast.

Jan 1, 1965

By A. P. Fletcher, K. Croteau

The intent of this paper is to cover some aspects of preventive maintenance methods which have come into wider usage in recent years as a means of increasing operating efficiencies. Particular emphasis is placed on lubrication and related servicing.

Jan 1, 1967

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By M. Harrison, C. H. Stockwell

"Metals vah1ed at more than $200,000,000 have been obtained, mainly since 1930, from the mines of northern Manitoba. The greater part of this production has been copper, zinc, and gold from the Flin Flon, Sherritt Gordon, and Mandy mines. The chief mines from which gold alone has been produced are God's Lake, Laguna, and Gurney. At present (May 1947) Flin Flon and Sherritt Gordon are the only producing mines, but the Nor-Acme property is being developed for large-scale production of gold. Large deposits of nickel and copper are being diamond drilled at Lynn Lake, and the Thompson, Ferro, and other properties are being developed. The mineral deposits lie within irregular or elongated areas of Precambrian sedimentary and volcanic rocks, surrounded by granite ( Fig. 1).The common rock types include basic and acidic flows, agglomerate, ruff, greywacke, arkose, argilli te, conglomerate, and their gneissoid and schistose derivatives. They are invaded by sills, dykes, and irregular bodies of gabbro and diorite, and all are cut by granite. Some of the sediments are interstratified with volcanics, and others are deposited unconformably on them.STRUCTURAL GEOLOGYLittle is known of the structures of the rocks in the area as a whole, because by far the greater part is unexplored or has been covered only by reconnaissance surveys. Available information indicates a general east structural trend in the southeast part, whereas in the west part the folding is mote complex with no definite overall trend. However, in a few small areas in the western part where detailed work has been done, as around the Flin Flon, Sherritt-Gordon, Nor-Acme, and other properties, the structure is fairly well known. The following descriptions apply chiefly to these areas ."

Jan 1, 1954

By K. R. Nichol

The author points out that corrosion works 24 hours a day, every day. It is an economic reality that the cost of corrosion is inevitable and that its cost should be incurred in the least expensive way. An economic evaluation technique to properly assess its relative impact is the Discounted Cash Flow Method. Various remedial and corrosion control measures are available and these, when coupled with a planned corrosion control program, help reduce the cost of corrosion.

Jan 1, 1973

By SANDVIK WHITE

The mining industry produces approximately 4-7% of global greenhouse gas (GHG) emissions. It is fundamental for mining operations to take immediate sustainable action to actively contribute to an emissions-free future for the next generations. The mining industry has traditionally relied heavily on diesel technology and transitioning to more sustainable solutions requires change management to drive cultural acceptance and new product development. Sandvik was interested to find out the lifetime emissions of a single drill rig and to compare similar application diesel and BEV drill rigs with same use profile to each other. That led the calculation and pondering towards comparing different countries and mine sites as well

Jan 1, 2023

By Nicholas Bonderoff, Amily Xu

The evaluation of battery electric vehicles (BEVs) in underground mines involves comprehensive business case analysis beyond just the capital and operating costs of the equipment itself. BEVs demonstrate benefits from an EHS perspective, reduced mine ventilation costs, lower energy operating costs, reduced overall GHG emissions (dependent on the source of electricity), elimination of DPM, lower equipment maintenance costs, and reduced cooling requirements in deep mines. When including batteries and supporting infrastructure, BEV capital costs are approx. 80% greater than that of diesel equipment. The project economics are highly dependent on the cost of electricity and diesel fuel, and these can vary widely depending on the location of the mining operation. Battery charging and swapping methodologies must be evaluated as there are a variety of approaches that can be employed which vary by manufacturer and type of equipment. Careful consideration of the cycle times, charging methodologies, and location of the battery charging infrastructure is necessary. Specific operating conditions must also be taken into consideration. For example, the time for blast gases to clear will be increased by reducing ventilation flow, and the potential impact on production needs to be evaluated. Similarly, the electrical distribution system needs to be evaluated for peak loading conditions when BEVs are charging. Criteria including maintainability, reliability, commercial availability, and performance need to be evaluated. BEVs have fewer components than diesel equipment and this correlates to lower overall maintenance costs, however, BEVs require maintenance personnel with specific skill sets in order to maintain the equipment. Battery lifecycle costs need to be considered as battery replacement incurs significant capital expense. Some manufacturers offer services to offset these capital costs through usage agreements. Recycling and disposal of batteries at the end of their lifecycles also need to be considered. With the increased selection of BEV equipment that will be available in the next 2-4 years, 100% BEV adoption is also possible. We recommend a holistic approach when evaluating BEVs for underground mines. This will ensure that everything is considered in order to evaluate the full impact of BEV implementation.

Jan 1, 2023

By R. Mulligan

"The Cordilleran tin belt extends from the Seward Peninsula in westernmost Alaska to Mexico. Throughout the Canadian section, tin occurrences are mainly confined to a belt along the northeastern fringe of the Western Cordilleran sub-region; the boundary of this sub-region with the Eastern Cordilleran sub-region is most simply defined as the practical eastern limit of granitic and metamorphic rocks. The stratified rocks underlying this restricted belt are mainly late Precambrian and early Paleozoic miogeosynclinal sedimentary rocks, which are more or less metamorphosed but otherwise are generally equivalent to the less severely deformed rocks underlying the Eastern Cordilleran sub-region. They contrast with Late Paleozoic - Mesozoic eugeosynclinal volcanic-sedimentary assemblages farther west, but the granitic intrusions throughout are mainly of Late Mesozoic age. Thus, narrowly defined, the tin belt largely coincides with a lead-zinc-silver metallogenic province, whereas copper deposits characterize the eugeosynclinal regions to the west. In addition to the tin occurrences, which include the Sullivan lead-zinc-silver mine, Canada's only significant producer, the belt contains all the beryllium, most of the tungsten and many Iithophile-type molybdenum occurrences. Several types of occurrences of each metal are represented. Lithium occurrences in the Canadian Cordillera are notably rare, and these few are insignificant."

Jan 1, 1971

By Brian G. Pewsey

Located in the northern part of the Province of British Columbia, the Cassiar Mine started development of its asbestos orebody in 1952, and is currently producing 105.000 tons of asbestos fibre annually. The townsite is nestled in a beautiful valley and supplies more than average facilities. The fibre is shipped to more than 40 countries and is used in many industrial products.

Jan 1, 1978