Search Documents

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By H. J. Handewith

"After having performed qualitative and quantitative tests on nearly 550 rock specimens from tunnel projects throughout the world and comparing the results with actual boring in eight distinctly different rock types which varied in compressive strength from 12,000 to over 34,000 psi, it has been concluded that any rock -andesite, granite and even taconite -can be machine-bored. The question is -can it be bored economically? The intent of this paper is to delineate the investigative needs to accurately and reliably answer this question. A piece of NX core in the hand represents less than 50 per cent of the worthwhile geologic information that could have been obtained from a given core hole. A thorough site investigation by competent personnel can gene-rally foretell to what extent, if any, varying geologic conditions will hinder machine progress.A laboratory testing technique has been developed that has been correlated well (80 to 120 per cent) with actual boring results. This technique will be discussed in detail. Rock cutter life is a function of the penetration rate and the forces required to sustain that rate. Cutters are now, and will be for .some time to come, the single, most expensive consumable item involved in continuous tunneling in hard rock. It is by strict attention to predicting these rates and forces that tunneling costs can be optimized."

Jan 1, 1970

By H. J. White

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel- base superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES® 282® alloy for applications in aircraft and land base gas turbines and other high-performance high-temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (~ 900 °C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability, and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/ repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R- 41, Waspaloy, and 263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, we present (1) results from hot ductility testing of annealed and annealed/aged material; (2) results from Time Resolved X-ray Diffraction (TRXRD) studies during a welding thermal cycle of annealed and annealed/aged material, and (3) gas metal arc (GMA) and gas tungsten arc (GTA) welding of annealed and annealed/aged material.

Jan 1, 2010

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By T. Feldmann, G. P. Demopoulos

The adsorption of gold complexes on inorganic metal oxides has been mainly discussed in geochemical literature, but it is also of interest to the hydrometallurgical industry. This is so because it could be responsible for valuable metal losses or because it could potentially serve as alternative adsorbent material to activated carbon in certain cases such as from hot and acidic process slurries. This paper constitutes an early investigation into this subject by focusing on the effectiveness of FeOOH, Fe3O4 and Al2O3 as sorbent materials. All tests were done in a batch stirred-tank reactor under atmospheric conditions with synthetic gold(III)-chloride solutions at 23°C and 80°C, in the pH range of 1.6 to 9.0. Detailed kinetic tests were performed at different pH values (3 and 6) on FeOOH and Fe3O4 with solutions having gold concentrations from 5 mg/L to 130 mg/L. The adsorption of gold was found to be best both in terms of kinetics and loading characteristics at 80°C and pH=6. This was explained by a change in Au(III)-Cl speciation from a gold(III)-chloride complex to a gold(III)-chloride-hydroxy complex. By far, magnetite (reagent grade chemical) yielded the best gold adsorption characteristics making it an interesting sorbent material for further development considering that it can be advantageously recovered from slurry streams via magnetic separation. On the other hand, the tendency of gold(III)-chloro complexes to adsorb on metal (hydro) oxides needs to be taken into account to minimize undesirable metal losses in chloride-containing leaching media.

Jan 1, 2015

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By J. A. Beesley

This paper reviews contemporary international law concerning the seabed, current developments in the United Nations on the seabed, and the main outstanding problems. It emphasizes the importance that the Canadian government attaches to this area.

Jan 1, 1969

By R. P. Viljoen, A. D. Scheglov, A. L. Sokolov

"Abstract -The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonic­ magmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonically­ controlled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian plat­ form, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu rnineralization. lt does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By Afshin Sadri, Wai Lai Ying, Brycklin Wilson, Zoe Coull

"Although there have been great steps forward to integrate corrosion engineering into operations, there is still an underlying tendency for maintenance tasks to be performed in a reactive manner. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify leading indicators of failures. Prevention is generally less costly than repairs; moreover, when paired with appropriate monitoring techniques, intervention of corrosion protection can be more effectively timed and based on more accurate data. Hatch asset reliability studies show nearly 80% of defects are introduced through operations and maintenance. Therefore, proactive corrosion management can provide the necessary feedback to optimize operations and maintenance strategies preventing costly corrosion losses. Understanding corrosion risks gives a clear picture of the benefits of a proactive approach to asset performance. Monitoring techniques (Non-Destructive Testing, field testing, sampling, etc.) by nature are a more effective means of improving maintenance efforts and preventing corrosion losses than other methods (RCA, FMECA). This paper will outline the importance of proactive corrosion management and demonstrate its benefits through industry examples.INTRODUCTION Over the past few decades, with the growth of technology and awareness of sustainable development many studies have shown the benefits of a proactive approach to maintenance strategies. However, in practice there is still an underlying tendency for maintenance tasks to be performed in a “reactive manner”. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify defects and leading indicators to failures."

Jan 1, 2017

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By A. M. L. Cushing, S. Kelebek

Presently, adsorption is one of the effective methods of removing toxic contaminants from waste waters. The contaminants from metal mining industrial operations include an effluent water containing various types of heavy metal species at concentrations beyond the maximum allowable limits, which are 0.5 ppm and 0.3 ppm for nickel and copper species, respectively. Adsorption behavior of copper ions pre-chelated with diethylenetriamine (DETA) and triethylenetetramine (TETA) onto natural bentonite and peat has been investigated. Both natural bentonite and peat was found to be capable of removing these copper-polyamine complexes from aqueous solutions relevant to process water effluents. However, the adsorption capacity of bentonite was significantly higher than that of peat. Two models were used to study the adsorption kinetics: a pseudo-first-order rate expression and a pseudo-second-order rate expression. For both adsorbents, the data conformed best to the pseudo-second-order rate expression. Representation of the experimental data through adsorption models was also investigated. Out of the four cases considered, namely, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms, it was found that for both bentonite and peat, the copper polyamine adsorption data conformed best to the Dubinin-Radushkevich adsorption model. The Langmuir model also represents the bentonite-copper polyamine adsorption system reasonably well as the second best case, suggesting that the amount adsorbed on bentonite might be a monolayer with strong affinity.

Jan 1, 2015

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017