Search Documents

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By André Chagnon, Michel Malo, Benoît Dubé, Chantal Pelchat

"Abstract- In the southern Gaspé Appalachians, gold mineralization is spatially associated with the Acadian dextral strike-slip Grand Pabos-Restigouche fault system. Two different structurally-controlled gold prospects, the Lac Arsenault and the Saint-André-de-Ristigouche, are described to unravel the genesis of gold mineralization in this part of the Canadian Appalachians.At the Lac Arsenault gold prospect, gold mineralization consists of Au-As-Pb-Zn-Cu-(Ag) polymetallic fault-filled quartz veins with laminated textures emplaced in brittle-ductile sinistral X shear fractures. Mineralized veins are hosted by Middle Ordovician graywacke of the Arsenault Formation, belonging to the Dunnage Zone, the Early Paleozoic oceanic domain of the Appalachians. Terrigeneous rocks of the Arsenault are regionally metamorphosed at the lower greenshist facies and the mineralized veins are included in a zone of Fe-carbonate alteration.The Sb-Au-As mineralization of the Saint-André-de-Ristigouche gold prospect, in the southwestern Gaspé area, comprises extension veins in the extension direction emplaced in brittle conditions. Mineralized veins are hosted by calcilutite and laminated silty and argillaceous limestone of the Early Silurian part of the White Head Formation, which belongs to the Gaspé Belt, the Middle Paleozoic successor basin in the Gaspé Appalachians. Metamorphic grade of the White Head Formation in the southwestern Gaspé area is very low, but the gold mineralization is included in a zone of hydrothermal propylitic alteration which includes two Cu-skarn mineral occurrences. The Lac Arsenault gold prospect has many characteristics of "greenstone-hosted quartz-carbonate vein" deposits whereas the southwestern Gaspé area, which includes the Saint-André-de- Ristigouche gold prospect, shows affinities with the geological setting of sediment-hosted gold deposits (Carlin-like deposits). The two gold prospects are controlled by the Grand Pabos- Restigouche fault system but they were not emplaced at the same level in the crust. Acadian strikeslip fauting played a major role in their respective genesis in providing channelways for ore-bearing fluids. The recognition of the analogy of the geological setting of the southwestern Gaspé area with that of Carlin-like mineralization gives new ideas for exploration in the area and elsewhere in the Appalachians.Résumé - Dans le sud des Appalaches de la Gaspésie, on trouve des minéralisations aurifères spatialement associées au système de failles de coulissage dextre acadien de Grand Pabos-Restigouche. Deux indices très différents, Lac Arsenault et Saint-André-de-Ristigouche, sont décrits pour évaluer la genèse des minéralisations aurifères à contrôle structural de cette partie des Appalaches canadiennes. Au Lac Arsenault, la minéralisation aurifère comprend des veines polymétalliques à Au-As-Pb- Zn-Cu-(Ag) en remplissage de failles. Ces veines à texture laminaire se retrouvent dans des zones de cisaillement fragiles-ductiles senestres de type X. Les veines minéralisées sont encaissées dans les grauwackes d’âge Ordovicien moyen de la Formation d’Arsenault appartenant à la zone de Dunnage, le domaine océanique du Paléozoïque précoce des Appalaches canadiennes. Les roches terrigènes de l’Arsenault sont métamorphisées régionalement au faciès inférieur des schistes verts et les veines aurifères sont dans de larges zones d’altération dolomitique (Fe-carbonate).Dans le sud-ouest de la Gaspésie, la minéralisation à Sb-Au-As de Saint-André-de-Ristigouche est dans des veines d’extension comprises dans la direction d’extension et mises en place dans des conditions de déformation fragile. Les veines minéralisées sont encaissées dans les calcaires argileux et les calcilutites de la partie silurienne de la Formation de White Head qui appartient à la ceinture de Gaspé, le bassin successeur du Paléozoïque moyen des Appalaches de la Gaspésie. Le degré métamorphique des roches du White Head est très bas, mais"

Jan 1, 1998

To create a successful growth oriented diamond company that succeeds in the practical business of mining and selling rough diamonds, and which pursues an aggressive exploration strategy to seek and develop worldclass diamond mining opportunities in a market that has become increasingly under-supplied.

May 1, 2008

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV."

Jan 1, 2017

By D. A. Bordin, C. J. Newman, R. J. St. Eloi

"The requirements for a metallurgical acid plant treating smelter gases are both unique and demanding in terms of sulphur dioxide treatment and emission control. Since start up in 1981, the copper smelter at the Kidd Creek Division of Falconbridge Limited has undergone several major expansions. The expansion and modification of the acid plant has been an integral part of this process. Both production demands and government regulations dictate that this metallurgical acid plant be unique in terms of operating flexibility. The variable capacity to treat a wide range of sulphur dioxide concentrations, and the operating flexibility to control emissions are the topics of this paper.INTRODUCTIONThe Kidd Creek Division of Falconbridge Limitied is a base metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April, 1964. Mining operations began in 1966 with a 9000 tonne per day concentrator coming on stream in November of that year. In April 1972, a 108 000 tonne per year zinc plant was commissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 tonnes of ore per day . To expand zinc production, the world's second installation of the Cominco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 125 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No.3 tankhouse technology for the copper refinery.The smelter, which uses the Mitsubishi Continuous Smelting Process for the continuous production of blister copper from concentrate, went on line in June 1981. It has been expanded from its original capacity of 60 000 tonnes to 100 000 tonnes per year of copper.From the very early design stages for the metallurgical complex, the company had adopted a policy of constructing and operating modern plants which would meet existing and anticipated environmental standards. With this in mind, the decision was made to utilize the proven technology of fixing sulphur dioxide emissions, in the form of sulphuric acid. A 636 tonne per day single absorption contact acid plant was built to serve the zinc plant in 1972. In 1981, an 883 tonne per day double absorption contact plant was built to serve the needs of the copper smelter. The copper smelter acid plant has since been expanded to a design capacity of 1692 tonnes per day and it is the main focus of this paper."

Jan 1, 1989

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By Ferri Hassani

Some future challenges ? People ? Shortages of HQP (e.g. engineers, scientists, geologists) ? Environment ? Regulatory standards - GHGs and air pollutants ? Mine waste management and rehabilitation ? Downstream processing (e.g., alternatives to cyanide) ? Climate change adaptation ? Lowering costs and improving productivity ? Energy efficiency ? Mine automation ? Health and safety ? Deep mining

May 1, 2008

By H. Salamanca

Recently, the mining industry has become one of the leading target markets for the technology industry as they need to innovate in their productive processes in order to boost productivity, reduce operation costs, increase operation safety, and improve the quality of life of their workers. This work presents the technological developments that HighService has done in different stages of the mining productive processes to include robotic manipulators in their automation solutions as well as the development of new equipment and sensors. The robotic technology integration is presented in different applications such as handling and selection of cathodes in E-W machines, automation of base plate maintenance, automation of cathode stripping machine, and multi-tools handler for liner bolt replacement in SAG mill liner maintenance activities. The proposed solutions show technical and economical viability with low initial investment and short implementation period of six (6) to ten (10) months. The results have been validated in plant, obtaining higher production rates and availability.

Jan 1, 2007

By Harry J. Cain

Introduction The property of Pioneer Gold Mines of B. C., Limited, is located in the Lillooet mining district of British Columbia, on Cadwallader creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern railway. Milling by the present Company was commenced in 1924, a small amalgamation plant, consisting of a crusher, Bryan mill, and plates being operated until 1928. Tailing from this plant was impounded and later treated in the 100-ton continuous counter-current decantation cyanide plant which was erected during 1927-28 and placed in operation during May of 1928. A second cyanide plant, employing continuous counter-current decantation, having a nominal capacity of 200 tons, has been erected during the past few months and was put into operation during September of the present year. The ultimate capacity of the combined units of the present mill has not been determined, but it is expected to be much in excess of the rated capacity. The Ore The ore, as received at the mill, consists chiefly of quartz carrying free gold, with small amounts of pyrite, arsenopyrite, and pyrrhotite in evidence, though probably amounting to less than one per cent of the total. Some gold is very closely associated with the sulphides. The country rock is a basic igneous rock, probably an augite diorite. Near the vein it is highly altered to sericite, which slimes readily on grinding, and does not settle very well. The quartz is of two types, clear and ribbon. In the latter, the ribbons, which are not much thicker than paper, consist of shattered sulphides. In crushing this ribbon quartz, breakage is often along the streaks, exposing these shattered faces to advantage in subsequent treatment. While gold is the metal for which the ore is mined, some silver is also present and is paid for by the mint. It is, however, unimportant from a commercial viewpoint. From the standpoint of crushing and grinding, the ore might be termed 'medium 'hard'.

Jan 1, 1932

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By Maxime Tacher

BRP (Bombardier Recreational Products) designs and commercializes recreational vehicles such as watercrafts, sport boats, snowmobiles, ATVs... The Spyder roadster is the last product in the Can-Am product family lineup. To remain at the forefront of innovation, a hybrid motorization version of the Spyder is being developed in order to reduce fuel consumption and emission of greenhouse gases. But, the addition of electric components (e-motor, lithium-ion battery... ) raises the issue of added weight and volume. This article deals with the mass reduction of this Spyder by optimizing its frame.

Jan 1, 2011

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012