Search Documents

By Kuwauchi. Y., M. Barati

Recycling of dust using a rotary hearth furnace (RHF) has gained considerable attention in the past two decades for the sustainable production of steel with less environmental impact. In order to further promote the recycling of electric arc furnace dust and carbonaceous wastes using the RHF process, a mathematical model was developed to predict the reaction behaviour of dust-reductant composites. The reduction kinetics of zinc and iron oxides as well as the volatilization behaviour of volatile matter in the reluctant were considered. The modeling approach and some preliminary results are presented in this article.

Jan 1, 2011

By China University of Mining & Technology, Yuemin Zhao, Bo Zhang, Liang Dong, Zhenfu Luo, Chenlong Duan

"In China, approximately 65% of coal reserves are in the west region, where water shortage is a serious problem: high-efficiency dry coal beneficiation technology is desired. Using magnetic powder and fine coal as heavy medium, and using air as the fluidizing agent, a novel air dense medium fluidized bed separator is proposed for coal preparation. Coal can be efficiently separated according to density in the fluidized bed, where bed density is steady. The separator is highly reliable, the circulation quantity of heavy medium is low, and the gas distributor cannot be easily easily. The world’s first industrial modularized dry coal preparation plant was built by China University of Mining and Technology. Dry coal beneficiation technology was first used to produce low-ash coal. Results of industrial production show that the ash content of clean coal is 3.46%, the probable error E value is 0.055 g/cm3, and the organic efficiency is over 90%. The advantages of the modularized dry coal beneficiation system are the high separation accuracy, the simple process flow, the low operation cost, low energy consumption, and so on. This technology provides a new effective method for coal separation in acid region and coal tending to sliming.INTRODUCTIONCoal is the most important primary energy source in China, where coal output reached 3.68 billion tons in 2013 and represents approximately 68% of the primary energy consumption. Coal has made a great contribution to the development of the Chinese national economy, but it also brings serious environmental pollution. However, approximately 65% of coal reserves are in the arid west region in China where water shortages present a challenge for wet coal preparation technology. In addition, the abundant lignite resource, because it is easy to mud in the water, should not be treated with the wet separation method. Therefore, it is critical to develop highly efficient dry coal preparation technology to meet the demand in arid areas. Further, water resource shortages are a global problem, thus the development of efficient dry coal preparation technology in has potential application in other water-short countries like South Africa, Brazil, India and Turkey."

Jan 1, 2016

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen's University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

By H. Attia, S. Engin

This paper presents a practical approach for determining the optimal spindle speed and the depth of cut in a milling operation within the ever-increasing economic and technical constrains. Analytical modeling and experimental work has been carried out to predict chatter in such operations. The stability lobes determined from this analysis were then used as a constraint in the optimization of the cutting process. The optimal cutting conditions are determined for two different objectives: maximum metal removal rate and minimum cost per unit. It is demonstrated that this approach can be generalized to impose multi-level constrains, e.g., surface integrity and machining accuracy. The approach presented in this work was examined and validated on three NC milling machines. The productivity improvement, cost reduction, while respecting part quality requirements, is demonstrated.

Jan 1, 2006

By T. Kho, W. Zhang, M. E. Reed

The control of flash furnace heat balances is critical. Suspension smelting control and stability comes from stable operation of the heat balance, and this leads to a stable reaction shaft exit temperature. A number of flash furnace operations have been reviewed to determine if the application of this approach is beneficial for their operation. The cause and effect relationship between reaction shaft exit temperature with uptake and throat buildup is being enhanced with this work program. Our operating personnel are exposed to the operational hazards of cleaning this buildup from the throat and it is imperative that as an industry we continue to look for repeatable solutions. WorleyParsons has reviewed operational data from a number of flash furnaces and looked at the possible improvements that can be made to decrease variation in the reaction shaft exit temperature. The data assessed for each operation illustrate the need to fully understand the process inputs to the particular operation and to ensure that the control changes are correctly impacted. In the plant data that have been assessed for a number of operations combinations of feed changes and inappropriate process decisions have lead to changes in reaction shaft exit temperature which impact the overall furnace operation and the uptake shaft condition, and ultimately the boiler. INTRODUCTION In 2016 WorleyParsons jointly prepared a paper outlining the effects of heat balance control on the Olympic Dam flash furnace (Reed et al, 2016). That paper investigated the importance of heat balance control in flash furnaces and demonstrated the changes made at the Olympic Dam operation to control the heat balance in the furnace and the impact that change had. The operation is still using the tool to assist in trouble shooting performance and pinpointing problems that may lead to issues in the furnace throat and Waste Heat Boiler (WHB). As a result of the interest in the methodology and due to the issues surrounding safety and process performance caused by WHB throat buildup and damage, WorleyParsons approached a number of flash furnace operators to discuss the application of the approach at their operations.

Jan 1, 2019

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By H. Fuchs, W. Hilger, E. Prosser

"The Lone Gull discovery of Urangesellschaft Canada Limited was made in 1974 as a result of extensive exploration activities for unconformity related uranium deposits in the Baker Lake area of the Northwest Territories. The structurally controlled mineralization is hosted in Aphebian metasediments and intrusive granitic stocks located approximately 2 km south of the unconformity between the Lower Proterozoic Aphebian and the Middle Proterozoic The/on Formation.The original discovery was made with a helicopter mounted radiometric system during systematic prospection over the unconformity. Diamond drilling was first carried out in 1977 and continued, with an interruption in 1981, to the present. A total of 25,500 metres and 199 holes have been drilled and outlined three ore zones. Preliminary geological reserves are estimated at some 16 million kgs. U30 8 at an average grade of approximately 0.4%.IntroductionUrangesellschaft initially entered exploration in Canada as a participant in joint ventures in 1968, and was incorporated in Canada in 1974 as Urangesellschaft Canada Limited. Subsequently, UG was among the first companies to apply exploration criteria developed from the Athabasca Basin, namely the Middle Proterozoic unconformity over Archean/ Aphebian basement, for selection of exploration targets in the geologically similar Thelon Basin.The Baker Lake area in the Keewatin District of the Northwest Territories was selected from the extensive Thelon Basin because it had the best accessibility (Fig. 1). The hamlet of Baker Lake located close to the geographical centre of Canada, is largely an Inuit settlement with a population of approximately 1,100 inhabitants. The distance from Baker Lake to the Lone Gull property is about 80 km. Baker Lake is connected to the tidewater of Hudson's Bay via Chesterfield inlet and is serviced by scheduled domestic flights several times weekly from Churchill, Manitoba, about 650 km to the south."

Jan 1, 1986

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By R. Plassart, F. Laigle

"As a powerhouse, a transformer or a valve chamber, large underground caverns are a major element of hydropower plant. On the contrary to galleries and shafts which are linear and long underground structures, large caverns are designed with often complex geometries and large spans. Moreover, as these caverns are generally located on the foot of the hydraulic scheme, the high overburden is often responsible of a high stress state. Thanks to current experiences in France and around the world, the Hydro Engineering Centre (CIH) of EDF has defined great principles in the design of caverns leading to a more general methodology. The project of Tehri in India is an example of difficult ground, with in the same time a high overburden, a ductile material and an important schistosity. These physical realities are attempted to be approached in numerical modelling thanks to a constitutive law with softening behaviour and an oriented criterion integrated in the continuum model. As a result, a flexible support is advised, based on a high density bolt system and a thin lay of shotcrete. This methodology has been developed in the case of Gilboa in Israel, except the schistosity which has not been observed in situ. At last, the example of Gavet (France) illustrates a discontinuous case of numerical modelling for a good quality but fractured rock mass.PRINCIPES ET METHODES DE CONCEPTION DE GRANDES CAVERNESHYDROELECTRIQUES SOUTERRAINESRESUME Les grandes cavernes souterraines abritant les turbines, les transformateurs et certaines vannes sont des ouvrages majeurs dans les aménagements hydroélectriques. A la différence des galeries et des puits qui présentent de longs linéaires, les grandes cavernes sont des structures à la géométrie souvent complexe et avec des portées conséquentes. De plus, ces cavernes étant généralement situées en pied du circuit hydraulique, la grande couverture rocheuse peut se traduire par un état de contraintes important. Forte de ses expériences récentes en France et dans le monde, le Centre d’Ingénierie Hydraulique d’EDF a identifié de grands principes de conception des cavernes permettant l’élaboration d’une méthodologie plus générale. Le projet de Tehri en Inde est un exemple de terrain difficile, présentant à la fois une forte couverture, un matériau ductile et une schistosité marquée. Ces réalités physiques sont approchées au mieux grâce à la prise en compte dans les modélisations numériques d’une loi de comportement radoucissante avec un critère orienté intégré dans un modèle continu. Les résultats ont conduit à privilégier un soutènement souple basé sur un boulonnage systématique relativement dense associé à une fine couche de béton projeté. Cette méthodologie a ensuite été reprise pour le projet de Gilboa en Israël, exception faite de la schistosité puisque non observée sur site. L’exemple de Gavet (France) enfin permet d’illustrer un cas de modélisation numérique discontinue d’un massif rocheux de bonne qualité mais fracturé."

Jan 1, 2015

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

Up to thirty years ago, coal preparation in western Canada, except at four plants, had not included actual coal washing. The exceptions were at Nanaimo and Royston, B.C., where tub washers and wet tables were in use; at Hosmer, B.C., using. Robinson cones; and at Leitch Collieries, Passburg, Alta., using a feldspar jig. The two last named collieries had a short life and were not operating in 1920. The industry was divided, as at the present day, into two sections, steam (bituminous) coal and domestic (largely sub-bituminous) coal, the first generally supplying industrial needs and the second householcl and other heating requirements. The two sections overlap to some small degree today as prepared sizes, chiefly stoker, and briquettes, from steam coal are shipped for house-hold use, and domestic slacks are used in certain industrial plants. The .domestic operator, for reasons shown later, was not primarily concerned with actual coal washing as a phase of coal preparation, and bent his efforts to improvement of screening and loading plants, with hand-picking of coarse sizes. The bituminous operator, on the other hand, felt it necessary by 1920 to consider coal washing. When the mines were comparatively young, coal quality could be controlled to a considerable degree by selective mining, by leaving behind some of the seam or by-passing districts in a mine where the coal was of inferior quality to that in other districts. This obviously had its limitations, and so the next step was coal washing.

Jan 1, 1952

By S. K. Sharma, Sanket Bacchuwar, Prabal Kumar Agrwal, G. V. Rao

"Iron ore processing industries play a vital role in the Indian economy. At present Iron ore of around +64% Fe is used for production of Iron through blast furnace. To produce +64% Fe from low/medium grade ores, crushing & beneficiation is compulsory. But during these processes, large amount of slime is generated. It is estimated that 18% -25% of tailing is generated during the processing of iron ore. The iron ore slime is discarded because of its particle size and chemical composition not being suitable as feed to the blast furnace. Although the fines/slimes can be agglomerated to larger particle, the alumina to silica ratio which is normally more than one pose serious problem during sintering process and subsequent smelting in blast furnace. The alumina content in the slime needs to be reduced for it to be used as the feed for blast furnace. The sample assayed 61.40% Fe, 7.68% SiO2, and 1.52% Al2O3, LOI 2.63% and all other elements were found in critical limit. A series of 27 tests were conducted by using a spiral for optimisation of process parameters to produce a pellet grade concentrate from the stacked slimes obtained from Kirandul. This paper deals with the optimisation studies of various parameters of a spiral concentrator and helps to utilize the fines from tailing ponds.INTRODUCTIONReserves of high-grade iron ores are diminishing all over the world at an alarming rate. As a result, alternative ways of augmenting and conserving precious and non - renewable natural resources are being seriously considered. One such attractive option is the recovery of metal values from slimes / tailings. Iron ore tailings containing around 48 - 60% Fe are generated from the iron ore washing plants and are disposed into tailing ponds without any further utility. These tailings in the form of slimes are not suitable in iron and steel making due to the presence of higher amount of gangue constituents. Several beneficiation techniques have been tried from time to time to reduce the gangue so that the beneficiated products could be effectively used."

Jan 1, 2016

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By P. Karimi, A. Amini, H. Abdollahi, A. Mirzaeian

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2016

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019