Search Documents

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By M. Gangal, M. Grenier, D. Mchaina, S. Hardcastle

"Exposure to airborne respirable silica in surface and underground mine operations is known to be the cause of industrial lung diseases. For this reason, silica is a regulated substance and worker exposure must be monitored regularly. Diesel exhaust also contains substances which are potential caricinogens. In an underground setting, diesel particulate may be the main component of what is referred to as respirable combustible dust (ReD). Although diesel particulate or soot is not at present a rigorously regulated substance, new epidemiological data is prompting North American institutes and agencies to regulate diesel soot or RCD exposure. This paper describes a method where by silicaand RCD exposure may be determined using a single personal sample. In this method, an airborne respirable dust sample is obtained and analyzed nondestructively for silica components using an on-filter X-ray diffraction method. Filters are then ashed at 500°C in a muffle furnace over a four-hour period to determine mass loss due to RCD burning. Using on-filter X-ray diffraction analysis as opposed to redeposition of dust samples onto another analytical substrate allows the"

Jan 1, 1992

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By Robert B. Parsons

"A t last the legal red tape which has tied up flow-through share financing has been cut. New rules effective for deals signed after 1986 simplify flow-through financing by removing the necessity f or cumbersome agency relationships. But there is no free lunch-the new rules require increased government reporting. And beware federal tax reform promises to have a good look at the new flow-through share rules. IntroductionFlow-through shares have always worked better in theory then reality as an effective financing tool. The concept is straightforward: a transfer of risks, tax deductions, and potential returns. But the mechanics of the old flow-through rules made the transfer of risk impractical to impossible by placing the responsibility for incurring Canadian exploration expense (CEE) on investors. The new rules are significantly more realistic, shifting that responsibility to the issuing corporation. However, every silver lining must have a few clouds around it. In the case of the new flow-through rules, the more obvious negatives are increased reporting requirements and reductions in CEE eligible for flow-through by amounts of assistance received. The new rules are effective for deals signed after 1986, however, so a few old-style deals are still around. Practical Difficulties with Old RulesThe old rules which applied to investments in flow-through shares were structured so as to make it the responsibility of the investor, rather than the issuing corporation, to perform the Canadian exploration expense for flow-through. Since most investors had neither the expertise nor the inclination to incur the CEE, this requirement necessitated the use of cumbersome arrangements whereby the investors would appoint an agent (usually the issuing corporation) to incur CEE on their behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, the awkward legal structure of such an arrangement made the investor the ""principal"" incurring the CEE. As such, the requirements of the old rules were met and the investors could receive their flow-through share s."

Jan 1, 1987

By Patrick Mclaren, Peter B. Hale

Canada, with one of the largest continental shelf areas in the world, has done little to evaluate its offshore unconsolidated mineral resources which include heavy minerals (gold, chromite, rutile etc.) and industrial minerals (silica sand and aggregates). During glaciation much of the continental shelf was covered with an ice sheet and later subaerially exposed with the result that glacial, glaciomarine and fluvial processes deposited sediments that may contain heavy minerals derived from onland locations. With rising sea-levels, beach and nearshore processes may have served to concentrate heavy minerals by winnowing and removing the lighter mineral components. These potentially valuable resources can be found with suitable exploration techniques such as seismic profiling and bottom sampling. Gold deposits are known to exist off the coast of Nova Scotia, and on the basis of form er beach mining, gold deposits probably occur off Vancouver Island and the Queen Charlotte Islands. Large deposits of silica sand occur near the Madeleine Islands and it appears likely that supplies of marine aggregates are present close to urban markets or sites of future mega-projects such as oil field developments. This paper, which is based upon a review of literature and consultation with members of the Department of Energy, Mines and Resources' Coordinating Committee on Ocean Mining (DCOM), is the first step in assessing the Canadian offshore f or its resource potential with respect to quantified deposits, known and speculative mineral occurrences. Although this is a subjective evaluation, the potential appears promising. A more detailed resource inventory is required to provide a more certain assessment.

Jan 1, 1984

By Jean-Luc Collins

"This new tool can be used as a quick guide f or the assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type ""go or no go"" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break even while the other measures a probable value based on the asymptotic theory of statistical extremes.Its application is briefly illustrated by means of an underground gold mine extension project, an oil sands mine project and a polymetallic open pit project.Once a favourable recommendation has been obtained then a detailed ""cash flow after taxes"" analysis can be carried out for the project.IntroductionMany tools are used in financial decision-making such as the payback period, the discounted cash flow, the internal rate of return and the wealth growth rate (Berry , 1971).These tools are useful and meaningful in evaluating normal projects closely related to regular business where the number of assumptions made is usually very small and where the cost of capita! is usually selected as a discount rate or a hurdle value. In situations where a significant number of assumptions have to be made,two problems can emerge, namely:I. the risk involved is underestimated leading to a potential financial disaster; or2. a good opportunity is lost because the approach used in evaluating the project is too conservative.Each assumption has its own degree of uncertainty and it is well known that combining uncertainties together can lead to a total uncertainty of critical proportion. The easiest way to account for risk is to increase the discount rate or the hurdle value, but this approach alone is quite subjective and can easily lead to the problems described above."

Jan 1, 1993

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By Jean-Loui Frenetie, Françoi Himbeault

"Flow of traffic in the underground mine has been improved through the years with clever use of traffic lights. The evolution is characterized by three major design changes. This paper will scan the basic criteria of these designs.IntroductionMines Gaspe, formerly known as Gaspe Copper Mines Limited, is a member of the Noranda Group of companies. The mine is the ""raison d'etre"" of the town of Murdochville, located 600 m above sea level on the Gaspe Peninsula. Paved highways link the town with Gaspe, 95 km to the east, and with Anse Pleureuse, 400 km to the north, on the Gulf of St. Lawrence.The low-grade copper mineralization was discovered in 1921 at Copper Mountain by local prospectors, the Miller brothers. Noranda Mines Limited obtained an interest in the property in 1937. World War II interrupted exploration work and it was not until 195I that a decision was made to bring the property into production.Initially, operations were confined to the Needle Mountain underground deposits which commenced production in 1955. Between 1968 and 1982, low-grade ore from the Mountain open pit supplemented the production. Due to the depressed market, surface and underground operations were suspended in 1982. Needle Mountain underground mining resumed in the second half of 1984, but the Copper Mountain open-pit operation remained idle. Since 1979, more than 75 km of exploration drilling resulted in the discovery of two new deposits, one which is located under the town of Murdochville . Mines Gaspe's present ore reserve, approximating 8 million tonnes, will be depleted by the end of 1992."

Jan 1, 1988

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By K. D. Peaslee

Slag splashing is an important development that has dramatically improved BOF vessel campaign life and reduced operating costs. This paper highlights research from physical modeling work using a 1/8-scale room temperature model BOF and slag characterization studies from several plants in North America and China. In the model studies, gas flow rate during blow and viscosity of the liquid were found to be two of the most important factors to changing the overall rate of liquid splashed onto the vessel sidewalls. When the flow rate was increased or viscosity decreased, the lower regions of the walls were splashed at a much greater rate. It was also shown that by changing the lance height, more liquid was deposited in the upper regions of the vessel at the expense of lower regions. Reducing the number of nozzles was found to be the most effective method of selectively coating a particular vertical section of the wall. Studies of BOF's using slag splashing in North America and China showed a difference in the melting characteristics of the final slag. Generally, slag splashing is successful when the melting point of the slag is 220-270°C below the tap temperature to maintain a balance between fluidity and refractoriness.

Jan 1, 2004

By David J. McDougall

"IntroductionThe production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with the Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivières (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about the Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian rather than the English-Canadian milieu, but whatever the reason, the other Quebec iron work s have been generally ignored. All but one of the Quebec blast furnaces could be described as ""preindustrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day.Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence river. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces."

Jan 1, 1983

By Wang Wenqian, George W. Poling

"Devices and flowsheets for recovering fine placer gold are reviewed. Inefficiencies of gravity processing techniques are documented and discussed. Prospects of combining gravity and froth flotation techniques are presented. Possibilities of using other separation techniques, such as magnetic and electrostatic devices are also discussed.IntroductionSeveral new methods for beneficiating different types of placer ores have been developed in the last two decades. Improved efficiencies in the recovery of fine particles have been achieved by improving gravity flowsheets and machines as well as by developing multiple treatment techniques involving flotation, magnetic and electrostatic separations. Placer gold processing, however, has been an exception to some extent. Gravity concentration using riffled sluices accompanied by mercury amalgamation is still the main method in use today. Because of this, the recoveries of fine gold and the other associated values are often similar to those achieved several decades ago. For example, very few sluice systems recover significant placer gold finer than 100µm in size.Only a few proposals for using alternatives to simple gravity methods for recovering fine placer gold can be found in the published literature. The fixed, low gold price discouraged research in this field for many years. Development of more efficient processes has not kept pace with the recent rapid escalation in the price of gold. Froth flotation for saving fine placer gold might now prove economic, for example. This paper reviews literature published on the recovery of fine placer gold over the period 1907 to 1980. Suggestions for improving the performance in this field, based on the authors' current testwork, are also presented."

Jan 1, 1983

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By John H. Walsh

"ForewordPart I of this paper, published in the March 1992 issue of the CIM Bulletin, surveyed the probable consequences of a limitation on the emissions of carbon dioxide to the atmosphere for the steel industry. What might be termed the conventional responses to this restriction open to the industry were also surveyed in that section. This section, Part II of the paper, explores a new option - the possibility for the joint production of iron and liquid fuels useful for transportation purposes. In this case, it is shown that it is important to minimize the production of carbon dioxide during the reduction stage to maximize the proportion of the reductant carbon embodied in the fuel. It is also advantageous to conserve hydrogen in the reduction step. In essence, the same carbon fulfills two purposes: it serves as a reductant and fuel for ironmaking and then as a constituent of a liquid fuel. If recovered plastics could be used in ironmaking, the same carbon could serve three useful purposes in turn. The conditions and limitations for the joint use of carbon in such 'cascading' processes are explored below. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the turn of the century; that there will be a rising need for liquid fuels to supply the world's steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada's industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By K. S. Fraser, H. J. H. Pieterse

"A pressure oxidation plant to pretreat refractory sulphide ore at the Goldstrike plant in Nevada, was commissioned in early February 1990. The plant, with a nominal capacity of 1363 t/d, was commissioned over a one-week period and achieved design capacity and availability within ten weeks an unusually short period for a plant of this complexity.The pressure oxidation process is conducted under elevated temperature and pressure conditions, and in a corrosive environment. These conditions demand that the process and engineering design of the plant be carried out in a much more sophisticated and detailed manner than is normally required in a conventional gold plant.This paper provides an account of the process and engineering design of the Goldstrike pressure oxidation plant with special emphasis on the design of the vessels, slurry pumps, piping, valves, and control systems.BackgroundLocationThe Goldstrike property is located in Eureka County in northcentral Nevada on the Carlin geological trend. The mine is approximately 40 km northwest of the town of Carlin which is situated on Interstate Highway 80. The minesite is located 1700 m above sea level in the Tuscarora Mountains.Initial Goldstrike OperationsShallow, low-grade mineralization was discovered by diamond drilling in the Goldstrike area in the 1960s. A heap leach operation was established in the mid-I970s by the previous owners. The Post deposit was discovered in 1982. Gold production by mining and heap leaching reached I t/a (40 000 oz/a). American Barrick purchased the property in 1987 and started an aggressive program of deep drilling. This led to the discovery of the Betze and Deep Post deposits and established sufficient reserves to justify an initial 4100 t/d mill and a 5 500 000 t/a heap leach operation"

Jan 1, 1992