Search Documents

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004

By Ian E. Efford

The paper gives an assessment of Canada's energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada's energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977

By Edward Martinez

Due to its unique properties, chrysotile asbestos is used in many diversified applications. In recent years, a better understanding of the structure and properties of chrysotile has evolved due to the research efforts of many investigators. A summary of the results of some of these investigations is given. An attempt is made to show the relationships between the properties of chrysotile and its crystal structure. Examples taken from the literature are cited in which methods have been developed for modifying the properties to improve the performance of asbestos in some applications. These include the effect of pH on the positive zeta potential and the addition of sodium silicate to improve filtration characteristics. The dehydroxylation and formation of forsterite when chrysotile is heated are also discussed.

Jan 1, 1966

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944

By Stefan Planeta

On discute les performances techniques et économiques des méthodes d'exploitation à haut rendement dans les mines métallifères au Canada. L'accent est mis sur la dilution et pertes des réserves minières et sur les coûts opératoires et totaux. Une analyse technique de quelques opérations minières est également effectuée. Il ressort de cette analyse que les résultats réels des opérations minières en cours diffèrent souvent de ces planifiés suite à la dilution du minerai et aux pertes importantes des réserves minières. On propose, définit et discute un certain nombre des facteurs de performances technologiques et économiques pour pouvoir mieux apprécier les problèmes rencontrés dans plusieurs mines en opération. À l'aide des études de cas on démontre impact négatif de la dilution et des pertes additionnelles des réserves minières sur la rentabilité des opérations en cours et sur les nouveaux projets miniers. On conclut, que l'application des indicateurs proposés donnerait un outil valable, aux opérateurs miniers, aux niveaux de la planification, du suivi des travaux d'exploitation et d'éventuelles études comparatives entre les différentes situations minières. ABSTRACT The paper discusses technical and cost performance of bulk mining methods in Canadian U/G metal mines. It focuses on ore dilution, ore reserves losses as well as on operational and total cost. Technical analysis of some mining operations has been performed. It indicates that due to dilution and significant reserves losses, the actual results of mining operations often differ substantially from those planned. The paper proposes, defines and discusses several indicators quantifying technical and economical performance in order to assess better the problems encountered in several operating mines. The case studies presented here have demonstrated an adverse effect of dilution and additional reserves losses onto profitability of existing operations and new mining projects. It is concluded that the application of the above mentioned indicators may be beneficial for mine operators. They may become a very useful tool at the stages of planning, follow-up of mining works and with regards to comparative studies between different mining situations.

May 1, 2001

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

By W. Zheng

Pipelines can develop stress corrosion cracks in either intergranular or transgranular form. Since the mid-1980s, numerous colonies of transgranular cracks have been found across Canada and many other countries in the world. While the intergranular form of cracking has been well studied in the past 40 years, the mechanisms governing SCC in near-neutral pH environment, i.e., the transgranular form of the cracking, are yet to be understood in greater depth. Over the past ten years or so, a large number of research publications have been available on this subject and this paper summarize our latest progress in understanding the mechanistic aspect of the problem. Better understanding of the role of mill scale surface and the steel metallurgy in crack initiation has been indicated in the recent literature. However, the initiation of SCC in the lab research still relies on loading conditions that are far more aggressive than those encountered in the field. Most crack growth studies in the past are also performed under very aggressive mechanical conditions, which could have prevented the observation of environment effects. However, more recent research at lower K or Delta K ranges seems to suggest a strong role of the environment. Naturally, modeling of growth should reflect the effect of the environment, steel metallurgy, and the changing mechanical properties of the pipe steel with time. For a specific steel in a given environment, the crack growth rates tended to increase with the strain rate, indicated either by the nominal applied loading frequency or by the calculated crack tip opening rate. Future research needs to address the issue of concurrent growth of multiple interacting cracks. More attention should also be given to concurrent initiation of multiple cracks in a colony, as failure is usually caused by a coalesced crack not by an individual crack. The effect of soil environment should not be limited to the chemistry of soil solution; other factors such as cathodic processes, the variation of environment with time and physical conditions of coatings should also be considered as part of the study.

Jan 1, 2005

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By D. Maddocks

"IntroductionThe greater part of the iron ore industry in Canada is located along the Labrador-Quebec border on a geological formation known as the Labrador trough. The Labrador trough is a 700 · mile long geosynclinal segment composed of folded and faulted Proterozoic sediments, volcanics and intrusives, extending from Gagnon, Quebec, to the north west tip of Ungava Bay. This geosyncline can be divided into three parts (Fig. 1).The northern unmined part, extending from southern to northern Ungava Bay, is a low grade metamorphosed iron formation.The iron deposits of the central region, represented by Schefferville, are hematite-limonite ores formed by oxidation and leaching of an unmetamorphosed taconite formation. Average iron content of the ore is greater than 540Jo for direct shipping and 50% for plant feed.The deposits of the southern section (Carol Lake, Wabush, Mt. Wright, Gagnon) extend from just north of Carol Lake to Gagnon and is a metamorphosed silica-iron oxide (specular hematite and magnetite) formation averaging plus 30% iron.The mineral wealth of this area was first observed by Father Louis Babel about 1870 and again by Dr. A.P. Low of the Geological Survey of Canada in 1894. However, the remote location hindered development until after 1945. First production of direct shipping ore from Schefferville was in 1954. Production at Carol Lake commenced in 1962.This area now accounts for sixty million long tons (61 Mt) per year of processed iron ore products as follows:This chapter will concentrate on pelletizing and agglomeration as experienced at the Iron Ore Company's Carol Lake operation. However, whenever possible, reference will be made to alternate methods, procedures, equipment, etc."

Jan 1, 1989

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By V. Bazhko, V. Yahorava

The calcium sulphate waste stream of the wet phosphoric acid process, commonly called phosphogypsum (PG), contains the majority of rare earth elements (REE) initially present in the apatite feedstock. Mainly light and middle REE are present in PG and their total concentration ranges from 0.27% to 0.35% by mass. Worldwide, around 7 billion tonnes of PG have been produced to date at a current growth rate of 150-200 million tonnes per annum. In total, an estimated 21 million tonnes of REE are locked in PG waste dumps around the world. Due to the value of the REE contained in PG dumps a number of processes have been devised for their recovery. The majority of these processes applied complete or partial gypsum dissolution, but were deemed not viable due to high capital and operating costs. Mintek developed an alternative method for the recovery of REE from PG by applying Resin-in-Leach (RIL) technology. This technology was tested on PG sampled from dumps and current arisings from South African phosphoric acid production plants. The extensive testwork program included evaluation of various lixiviants and optimisation of lixiviant additions, optimisation of REE leach and adsorption conditions, batch equilibrium and kinetic adsorption tests, continuous RIL testwork and numerous variability tests. It was found that PG from different sources was highly variable, both in terms of REE recovery as well as physical properties of the material such as viscosity and filterability of the slurry. The recovery of REE varied from 15% to 80% depending on the origin of the samples. A high-level economic study indicated that at a price of >21 $/kg for mixed REE oxide product in conjunction with an overall REE recovery as low as 15% the economics of REE recovery from PG via RIL technology may already be favourable.

Jan 1, 2016

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By J. G. Martin, J. C. Campbell

THE VICTORIA JUNCTION 31,4-million-ton coal preparation complex went into operation in October 1976."' It is designed to produce a metallurgical coking coal by lowering the sulphur and ash content of the raw coal using a heavy-media cycloning process to treat deslimed crushed coal, with scavenging of fine coal by flotation from the primary minus-28-mesh screen product. A secondary H-M cyclone scavenges a thermal-grade coal from the primary H-M cyclone tailing.

Jan 1, 1985

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016