Search Documents

By C S. Walker

This paper analyzes the physical, operational and economic site conditions which were conducive to the design of a diesel-electric power plant wherein the over-all use of the thermal energy of the fuel exceeds 80 per cent. The heat energy supplied to the diesel engines is recovered in power generation, vapour phase cooling, waste heat boilers, air to exhaust gas heat exchangers and lubricating oil coolers. Electric boilers are also integrated into the plant design to enable the ratio of electric power output to heat recovery to be varied to suit the seasonal and daily variations. The criteria relative to thermal and electric power design requirements are discussed, and the design details of some parts of the plant which conform to these criteria are illustrated. Some data in regard to the actual operation of the plant over a short period are also included. Introduction THE Cantung mine (Canada Tungsten Mining Corporation) is located some 180 miles north-east of Watson Lake, Yukon Territory. It is situated on the upper reaches of the Flat river at an elevation of about 3,700 feet.

Jan 1, 1965

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one's thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By C. G. Harris, R. Sluyter

The purpose of an undercut is to undermine a block of ore which will then proceed to cave into draw holes just below the undercut. Undercut-ting is the final and most vital phase in the development of an ore block. Since its purpose is to undermine and induce caving into a block of ore, great care must be exercised to avoid premature caving by removing only enough rock to permit undercut development to proceed. Several undercutting methods, used over a twenty-year period, are re-viewed and their suitability is com-pared with ideal requirements.

Jan 1, 1960

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By D. A. Grieve

"Mineable coal seams in the East Kootenay region belong to the Mist Mountain Formation of the Jurassic -Cretaceous Kootenay Group. Three structurally separate coal fields (Crowsnest, Elk Valley and Flathead) are recognized, all of which are characterized by compressional tectonic features such as f aiding and thrust faulting, and by /ate-stage normal faulting. Tectonic history has greatly influenced coal mineability and quality. Coals range in rank from low to highvolatile bituminous, and reactive maceral content ranges from less than 60% to greater than 90%. A wide range of metallurgical and thermal coal qualities is found. Measured reserves (up to 1981) include 1.03 billion metric tonnes metallurgical and 165 million metric tonnes thermal coal. Introduction a) Location -Coal fields of the East Kootenays region occur in the Front Ranges of the Rocky Mountains, within 30 km of the Alberta -British Columbia boundary (Fig. 1). They extend over 175 km north from near the U.S. border, and occupy the regions of the Crowsnest Pass and Elk and Flathead River drainages. The deposits are accessible from Highway 3 (Fig. 1) and various secondary roads. The towns of Fernie, Sparwood, Elkford, Coleman and Blairmore serve the coal industry. East Kootenay coal deposits are contained in three structurally separate coal fields, the Crowsnest, Elk Valley, and Flathead coal fields (Fig. 1). Coal is currently being produced by B.C. Coal (now Westar Mining Ltd.) at Sparwood, by Fording Coal 20 km north of Elkford, by Crows Nest Resources at Line Creek 15 km southeast of Elkford, and by Byron Creek Collieries at Corbin. Westar Mining has also constructed a new mine on the Greenhills Range 8 km northeast of Elkford. Pre-requisite engineering and environmental studies have been carried out on the Elco Mining property, 35 km north of Elkford, and on the Sage Creek coal property near the U.S. border (Fig. 1). b) Coal land tenure -Coal rights in the East Kootenays are either held as freehold land, or are licensed from the provincial government. The former category includes lands acquired under the Railroad Act of 1890. Shortly after this the federal government also obtained 50,000 acres of coal-bearing lands from the Crown Provincial, the so-called Dominion Government Coal Blocks. Major holders of coal rights in the area are Westar Mining and Crows Nest Resources. Large blocks are also held by Fording Coal and related companies, Sage Creek Coal, and Canada Permanent Trust Company as trustee for Elco Mining, and small blocks are held by Byron Creek Collieries and Coleman Collieries. In addition the provincial government holds an area in reserve for possible future use of B.C. Hydro at the extreme north end of the Elk Valley coal field."

Jan 1, 1985

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By L. L. Sirois

Because segments of the Canadian mineral-based economy are dependent totally or in part on foreign sources of certain minerals, their well-being may well be affected by inability to obtain these minerals. Where such dependency exists, it is therefore important that contingency plans be available to counteract possible price increases or lack of supplies by means of technology, developed well in advance of any pending crisis . Canada is vulnerable to possible future real or artificial shortages of certain foreign-produced mineral commodities, and science and technology can provide information for the development of policies for counteracting efforts by foreign exporters to control prices or limit supplies.

Jan 1, 1977

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By W. C. Whittaker

"This paper gives a brief resume of the changes in the market picture for Western coal since 1948. It then analyzes present markets and recent developments in Western Canada, the western United States and Japan, and forecasts future markets in these areas to 1975.INTRODUCTIONCOAL HAS BEEN MUCH IN THE NEWS OF LATE, both in the United States and in Canada. In the United States, this is because of the booming condition of the industry and because of the purchase of control of a number of America's largest coal producers by the integrated oil and metal producing companies seeking additional fossil fuel reserves and diversification. In this regard, it is interesting to note that ownership of America's largest strip coal producer was recently acquired by one of the world's largest copper mining companies. In Canada, the conclusion of several large-scale, long-term contracts for the sale of coal to the Japan Steel Group and the projected use of Canadian coal in steel mills in the western United States has focused much attention on the coal industry."

Jan 1, 1968

By Saravarim A.

"The aim in flotation systems is to control the grade and recovery of the product., numerical method or sampling and analysis is used to achieve this goal. Weakness of measuring instruments, lack of process knowledge, deficiencies in management and data processing in the control of flotation cells, has led the academic and industrial units to use numerical models. In this regard, using the results obtained from the experimental design carried out in the DTP line of Gol Gohar industrial and mining complex, a regression model was developed based on the analysis of variance. To present this model, after variance analysis of factors and interactions, all models were investigated and the final model was created based on 75% of the data. The model was tested with the remaining 25% of the data to confirm the goodness of the fit. The coefficient of determination for training and testing resulted 71% and 74%. Moreover, a feed forward back propagation neural network with different layers and neuron was used to model the results. The best network structure was 6-27-1 and the coefficient of determination for this network was 99% and 98% for training and test respectively. Given the complexity of neural network models and the relatively low accuracy of the regression model, neural network has a priority assuming we have access to a specialist. In addition, the results obtained from neural network can be used as expert systems to control and optimize the flotation cells.INTRODUCTIONThe primary objective of the flotation cell control is to maintain the product's (in this case tailing) recovery and grade, which represents the index for process efficiency and product quality. Continuous estimation of these indexes requires a significant amount of maintenance, and calibration of the continuous analyzers, in order to maintain an acceptable level of accuracy. Weakness of measurement equipment, lack of process knowledge and the general deficiency in management and processing of data in the flotation cell control, will lead industrial units to use smart methods such as mathematical models, regression and neural networks in near future (Panahi, Abdollahzadeh, & Sam, 2010). Artificial neural networks are inspired by the very complex structure of human brain in which millions of nerve cells solve problems or store information by communicating with each other. The duty of neural networks learning. It should be noted that learning in artificial neural networks is limited, and what is practically considered is the computing power of the network. A neural network consists of units called neurons, and has the capacity to handle a set of input data to produce a desired output data set. Each of these input and output data sets can be assumed as a vector (Soltanmohammadi & Noparast, 2006)."

Jan 1, 2016

By Ree Llewellyn

"It has been estimated conservatively that the costs of wear damage and friction in the Canadian mining and mineral processing industry amount to over one billion dollars per year. These are mainly incurred through the repair or replacement of worn parts and production losses from related equipment downtime. The selection and application of the most appropriate wear protection components and systems, can thus have a very significant influence on productivity, profitability and global competitiveness.Details are presented of the wide diversity of materials used to counteract the varied and often complex wear attack mechanisms that occur in surface mining. The majority are various forms of steels and irons with generally very high hardness. However, they also include relatively soft elastomers and polymeric products.The main characteristics and applications of the different classes are reviewed. Case studies record significant performance improvements achieved through more judicious selections. Finally, some new developments which reduce maintenance charges by substantially increasing wear component life, are described."

Jan 1, 1996