Search Documents

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By T. T. Ni

FOR MORE THAN 200 years, the Kochiu district of Yunnan province has been, and it still is, the hub of China's tin industry. The district produces annually from 80 to 90 per cent of that country's out-put of tin, which averages about 9,300 tons a year and places China fifth among the tin producing nations of the world. The tin ore reserves of the country are estimated (1) at 1,873,370 metric tons, of which 1,500,000 tons are in the Kochiu district. The mill of the Yunnan Consolidated Tin Corporation, described in this paper, is the only one of its kind in China. MINING AND SMELTING There are only two tin mines in the Kochiu district operating with modern equipment -the Hsin-Chang and the Lao-Chang, both owned by the Yunnan Consolidated Tin Corporation, a government company. The Hsin-Chang mine has four working levels with cross-cuts 6 ft. by 6 ft. and is equipped with steel mine cars and trucks to haul the ore. The ore is hoisted to surface in a three-compartment shaft and transferred to the mill by a 4-kilometer aerial tram. The Lao-Chang mine has two circular shafts 656 feet apart, each equipped with two cages. Haulage-ways 1,600 meters and 1,000 meters long, respectively, have been driven to the southwest from these shafts and are connected by three cross-cuts.

Jan 1, 1951

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By R. B. Fermor

"AbstractAttention is drawn to the ventilation problems arising from the use of diesel vehicles underground, especially in view of the fact that diesel fumes in combination with other pollutants may be more harmful than diesel fumes alone or the other pollutants alone.Means for minimizing the harmful effects of using diesels underground are listed, and the quantities of air' required in mines in which diesel-powered vehicles are used are discussed. Mines are classified in three categories on the basis of severity of ventilation problems, and statistics are given for these categories.Details of the various components contributing to total ventilation needs are given, and the ventilation needs of individual mines in the three categories are listed. A description is given of the principles according to which main ventilation coursing is planned and the selection and siting of main fans is discussed.General Considerations in the Use of Diesel-Engined Vehicles UndergroundIN ORDER to reduce physiological hazards, present and latent, to workers in mines in which extensive use is made of diesel equipment underground, it is important that mine ventilation systems reduce the concentrations of rock dust, diesel fumes and particulate matter as rapidly as possible to an acceptable level in all parts of the mine.There is some evidence that the long-term effects of a combination of the above pollutants are greater than those of anyone of them alone, which makes the problem even more pressing."

Jan 1, 1977

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By Peter Wells, Gordon Marrs, Dominic Fragomeni, Warren Holmes, Daryl Macnamara

"LocationThe Strathcona mill ofFalconbridge Limited is located in Onaping, Ontario, 50 km northwest of Sudbury.GeneralOre from the Falconbridge mines in the Sudbury Basin (Strathcona, Fraser, Onaping, Craig and Thayer Lindsley mines) is processed through the Strathcona mill with 8500 t of nickel ore and 1500 t of copper ore being treated daily. Current capacity is -3 Mt of ore at 1.8% Ni, 1.9% Cu combined grade. Custom feeds are also processed. The valuable minerals in the ore are pentlandite (FeNi)9S8, chalcopyrite (CuFeS2) with some cubanite (CuFe2S3) and very minor nickel sulphides/ arsenides. Cobalt is present mainly in solid solution in pentlandite. There are small but economically important concentrations of precious metals including platinum, palladium gold, and silver. The common non-sulphide gangue minerals are feldspar, quartz, mica, talc, and chlorite while pyrrhotite (Fe7S8) is the major gangue sulphide. The pyrrhotite contains between 0.6% and 1.2% nickel in solid solution and additional nickel as exsolved pentlandite in micron sized blebs. The nickel and copper ores are batch-crushed in a two stage dry crushing plant and then ground in separate circuits. Concentration by flotation and magnetic separation produces a nickel concentrate assaying approximately 16% nickel plus copper and a copper concentrate assaying 30% copper and 0.4% nickel. The nickel concentrate is trucked as a slurry to the Falconbridge smelter while the copper concentrate is trucked as filter cake to the Kidd Division of Falcon bridge"

Jan 1, 2000

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By A. R. Chambers

Malagash received its name from the Indians many years ago on acco.unt of its turbid (milky) waters, although,' the red men did not appreciate the significance of this turbidity, and were, of course, entirely ignorant of the crystal beds of pure salt that lay beneath their feet. The salt lake of the Mississippian, or Lower Carboniferous period, in which these beds occur, was apparently a large one, for there is evidence of its existence at intervals all the way from Sydney, Cape Breton, to St. John, New Brunswick, 300 miles as the crow flies, and there is no knowing what its other dimensions may have been, as much of this horizon is now buried on the one side beneath the waters of the Gulf of St. Lawrence, and on the other underneath the Atlantic ocean. About midway of the area and underlying the counties of Colchester and Cumberland, there occurs a synclinal basin of which the Malagash salt outcrop forms only a small portion of its northern limit. This basin has been described very fully by A. C. Hayes. (1) The operations carried on at Malagash since Hayes wrote his report have brought to light very little in the way of new geological data, except to confirm his pre-dictions as to the probable faulting of the salt strata, and the effect which these faults would have on mining operations.

Jan 1, 1924

By S. Nikolic

"Calcium ferrite slags are currently used in a number of copper-converting processes. Despite the industrial importance of this system the phase equilibria have not been fully investigated. Characterization of this slag system is necessary to improve the control of process parameters, including fluxing and operating temperatures. Recently, a modified experimental method has been developed; this involves rapid quenching of slag samples equilibrated at high temperatures with the resulting phase assemblages analysed using electron probe microanalysis (EPMA). In the present study, experiments were completed under controlled temperatures and oxygen partial pressures using CO/C02 or H2/C02 gas mixtures. The investigated slags were supported during equilibration by a substrate of the primary phase. This technique removes the limitations arising from the use of crucibles and facilitates rapid quenching of the melt. Experiments were carried out at 1200°C and 1250°C (1473 Kand 1523 K) and in the composition range 0-40 wt.% Cu20, 0-25 wt. % CaO and 45-80 wt. % Fe203. Liquidus and solidus data are reported for the primary phase field of spinel between the oxygen partial pressures of 10-4.5 to 1 o- 6-5 atm. The analyzed compositions of liquids and solids are used to construct the phase diagram of ""Cu20"" -CaO-""F ez03"" system in equilibrium with metallic copper at fixed oxygen partial pressures."

Jan 1, 2007

By A. W. Jolliffee

ANY attempt to forecast the mineral resources of a largely unknown region is hazardous and, in the case of the Northwest Territories, such a task is even more hazardous than usual. This is not merely because of the immense territory involved (over a million and a quarter square miles), only a small fraction of which has ever been explored or prospected, but also be-cause both the geology and mineral deposits thus far examined show many unique features, and, finally, because the region is being actively prospected at the present time. However, in view of the present widespread interest in Canada's mineral resources, a brief compilation of what is known regarding mineral occurrences and geology in the explored parts of the far north seems timely. From these assembled data, a few inferences are warranted as to future mineral production from this region. HISTORY The story of mineral discovery in the Canadian northwest is a fascinating one. As well, it abundantly illustrates the importance of mineral occurrences in indicating future mining possibilities. The same sequence of events has repeated itself too often to be merely fortuitous.? In most cases, the dis-covery of a mineral deposit of possible economic value has been foreshadowed by the finding of the valuable mineral or an associated mineral in the same district, generally in small quantity, by an early explorer or traveller. Thus, John Franklin reported oil seepages from the base of Bear Rock, near Nor-man, at almost the very spot where oil was struck nearly one hundred years later. Again, some would-be Klondikers, deterred by the hardships of the route, remained to prospect around Great Slave lake, and were the first to report the Pine Point lead-zinc occurrences there and the gold-bearing veins on Yellowknife bay. Sporadic prospecting followed at the latter locality for over thirty years before the recent rich strikes were made. Similarly, in 1847, Dr. John Rae picked up a boulder of copper ore south of Rankin inlet, on Hudson bay. More than eighty years later, a body of copper-nickel sulphides carrying values in platinum metals was found at this locality. Also, the report of cobalt bloom on the east coast of Great Bear lake brought back by a Geological Survey of Canada party in 1900 was a factor in the events leading to the discovery of silver and radium there in 1930.

Jan 1, 1937

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

A brief description of the hydro-gen reduction of nickel from ammoniacal solutions by the Sherritt process is given, indicating how this procedure can now be used to coat a great number of materials -particularly powders -with nickel or cobalt, whereby so-called composite powders are produced. The technique for the production of composite powders is described, particularly with regard to the surface activation of noncatalytic powders, whereby it is possible to coat core powders uniformly with nickel or cobalt. The properties of some of the more interesting composite powders, such as Ni/ AI, Ni/WC, Co/WC, Ni/Graphite and i/P, are discussed as well as possible fields of application for these new products. INTRODUCTION DURING the last decade, no-table advances have been made in pressure hydrometallurgy, so that large quantities of three of the more com1r.on metals, copper, cobalt and nickel are now produced on a commercial scale by hydrometallurgical processes.

Jan 1, 1963

By Jr. Jones

This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded. A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.

Jan 1, 2012

By A. G. Roach

Introduction This paper deals with the operations and plant of the Craigmont Corundum Project, formerly of Wartime Metals Corporation but now under the Mines Section of the Resources Development Branch of the Department of Reconstruction and Supply. Corundum is recovered by the re-treatment of an old tailing deposit at Craigmont, Ontario. Crude concentrates so produced are shipped to the plant of the American Abrasives Company, Inc., at Westfield, Mass., for final processing and distribution to the abrasive industry. The plant was recently described in a paper entitled Craigmont Corundum which was presented by the writer before the Chicago meeting of the A.I .M.E. in February, 1946. General The Project is located on? lots 4 and 5, concession XVIII, township of Raglan, Renfrew county, Ontario, near the village of Combermere, which is on Highway 62. The property is about 135 miles from Ottawa. The general area enjoys a pleasant climate with moderate summer temperatures, though the winters are rather severe, the mercury frequently falling to - 35 deg. F. The excellent boating, fishing, and hunting have made the district a favourite resort for tourists. Lumbering is the main industry. Some farming is carried on, but the soil is poor and much of the land is hilly and rocky. There are no other operating mines in the immediate vicinity, though several 'industrial minerals', including mica, feldspar, nepheline, beryl, socialite, and others have been produced in the area. The district is drained by the York and Madawaska rivers and is generously dotted with large and small lakes. The general elevation is about 1,000 feet above sea level, though numerous hills rising several hundred feet give a rolling appearance to the landscape.

Jan 1, 1946

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005