Search Documents

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By H. O. Lien

Among the known iron deposits in Canada, many are of low grade and require beneficiation to produce an acceptable blast-furnace feed. Some of the deposits have never been considered for commercial exploitation due to the lack of a suitable concentrating process. A number of deposits of this type are located in Northern Ontario. The problem in upgrading these deposits is three fold. Firstly, the iron occurs as a mixture of magnetite and hematite. Secondly, the grain size of the material can be fine to very fine. Thirdly, the complex mixture of gangue minerals, which consists invariably of silica, flaky silicates and carbonates, slimes excessively on fine grinding. Algoma's efforts to concentrate these iron-bearing materials culminated in the development of a "Selective Flocculation and Desliming Process" employing slimes removal as the sole beneficiation technique. The process was applied successfully in the laboratory using two stages of grinding and a total of seven deslimings. Prior to the removal of slimes, the iron-bearing fines were selectively flocculated from a thoroughly dispersed pulp using a modified starch as flocculant, Sodium silicate was employed as dispersant. An attempt was made to optimize some of the process variables using material from one specific iron formation near the town of Geraldton in Northern Ontario. The preparation of the starch proved most critical. This matter, and the method used to evaluate the degree of breakdown of the starch molecule, are therefore discussed in some detail.

Jan 1, 1978

By M. S. Badollet, N. W. Edgerton

"A study of the physical properties of long grades of asbestos fibers imported into the United States during the past eight years has disclosed information that will contribute materially to effective selection and use of fibers for electrical products. The study embraced fiber lengths, volume resistivity under three different conditions, total iron by chemical analysis, magnetic rating, conductivity of an aqueous ex-tract and its sodium chloride equivalent.The fibers examined included chrysotiles from Rhodesia, British Columbia, and Barberton area; marlime from Bechuanaland and Province of Quebec; amosite and crocidolites from Africa and Australia; and anthophyllites from Mozambique and from Georgia in the United States. Volume resistivity values provide a relative basis for estimating the electrical performance of end products; magnetic rating -an estimate of the quantity of iron compounds present in excess of those in the asbestos structure; conductivity of an aqueous extract; and an estimate of the ionizable impurities in fibers.Tests of these factors yield in-formation, not heretofore generally known, which may serve as a guide in the evaluation of asbestos fibers for electrical products."

Jan 1, 1960

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

Eagle Plains Resources? Exploration in the Northern Cordillera ?Eagle Plains Resources Ltd. (EPL) is actively exploring for Zn-Pb deposits in the northern Cordillera in both carbonate-hosted and shale-hosted (sedex) environments. ?This presentation will review some of the significant carbonate-hosted Zn-Pb showings occurring in the Mackenzie Mountains, NWT and make limited comparisons with sedexdeposits in the adjacent Selwyn Basin.

May 1, 2006

By D. J. McCulla

Mineral development and utilization affect the health of the economy and the pattern of long-term development throughout Canada. There are many diverse opinions on the contribution of minerals to the economy, but there is a dearth of adequate quantitative information. This paper discusses some recent research and provides some new information.

Jan 1, 1977

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By B. N. Church, J. J. Barakso, A. F. Bowman

"An evaluation of mineralization in the Goosly- Owen Lake area of central British Columbia is the result of a comprehensive geochemical study of rock samples obtained from a regional geological survey. The dispersion of metals in country rocks about a line of Tertiary intrusions suggests that these igneous bodies may be genetically related to known sulphide replacements, disseminations and vein deposits. The geochemical investigation is based on the determination of 12 elements from samples gathered from more than 800 scattered field stations. To assist processing and interpretation, the data are subjected to a variety of statistical procedures, including correlation of the elements, factor analysis, clustm• analysis and computer contouring of the elements. Some practical applications of rock geochemistry in regional exploration are indicated."

Jan 1, 1976

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By Z. D. Hora

Sand and gravel resources of the southern coastal region of British Columbia may be linked to various episodes of Wisconsin glaciation. During Wisconsin and probably earlier times, the Fraser Lowland and coastal areas were subjected to repeated glaciations separated by non-glacial intervals. Each major glaciation was accompanied by isostatic and eustatic changes in sea level up to 200 m or more. As a result, the Lowland was covered by the sea during much of Quaternary time. Because the Fraser Lowland is surrounded on two sides by high mountain ranges, glaciers terminated in the sea during their maximum advance. Therefore, meltwaters released during deglaciation, together wit h retreating glacier ice, could produce widespread and extensive sand and gravel deposits both along the coast and throughout the Fraser Lowland and adjacent areas.

Jan 1, 1984

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By P. G. Claridge, G. P. Holmes, M. A. Redfearn

"IntroductionThe purpose of this chapter is to describe current practices in operation and maintenance of flotation circuits in Canadian mineral processing plants. The chapter consists of five sections covering description of equipment, typical flow diagrams, operating practice, instrumentation and maintenance. The approach to this subject matter is intended to be practical in nature, hence no deeply technical treatment of flotation theory will be included.Flotation is an extremely common method of beneficiation of ores. Reasons are the relatively low cost of flotation compared to many other processes, the wide range of minerals to which flotation may be applied and the high efficiency of separation which can usually be achieved. The flotation process as we know it today has been developed within this century and it has had a major impact on the mining industry. While flotation is commonly considered to be important because it provides a relatively simple method of separating minerals in complex ores, the availability of flotation has also made a multitude of mineral deposits in Canada into economically viable mining operations because it allowed production of a concentrate of valuable minerals from the ore. These concentrates could then be transported from geographically remote locations to centraHzed plants for further processing, although the existence of the remote and perhaps small ore body alone would not have justified installation of metallurgical processing plants on site and the grade of ore would not have justified direct shipment of ore.Some of the more common minerals concentrated by flotation are sulphides of copper, nickel, cobalt, iron, zinc, molybdenum, lead and arsenic, as well as non-sulphides such as sodium chloride, potassium chloride, phosphates, silicates, chromite, fluorite, limestone and coal. Precious metals are also recovered by flotation, generally in association with another sulphide mineral."

Jan 1, 1989

By C. G. McLachlan

Abstract This paper deals with the application of the cyanide process to recover gold from a pyrite concentrate produced by means of differential flotation. This concentrate before cyanidation contains from 0.09 oz. to 0.14 oz. gold per ton, of which only about 60 per cent is recoverable. The rest is so fine that it remains interlocked in the pyrite and therefore is not acted on by the cyanide. The concentrate also contains about 15 per cent pyrrhotite and 0.4 per cent chalcopyrite, both of which are cyanicides. The cyanicidal effect of the pyrrhotite is inhibited by preacracing the pulp with lime, and maintaining a high lime alkalinity during cyanidation. The effect of the chalcopyrice is reduced as far as possible by removing those particles which are free by means of a further flotation step immediately prior to cyanidation. This involves the flotation of some very fine material. After nullifying as far as possible these two cyanicides, the concentrate is cyanided directly, i.e., without being roasted. This leaves the pyrite available for subsequent sale as a source of sulphur dioxide and sulphuric acid, and the entire residue of the cyamde plant, amounting to about 500 tons per day, 1s now being disposed of in this way. Prior to deciding on direct cyanidation, a number of laboratory roasting tests were made. These showed chat, 1f proper control were exercised, a better recovery of gold could be effected from the roasted product than by the direct method of treatment. The tests also showed that the capital cost o the plant would be much higher than that needed for the procedure adopted. The possibility of subsequently selling the pyrite for its sulphur content would also have been eliminated. Introduction A previous paper has described in considerable detail the application of the flotation process to improve gold recovery from Noranda's milling ore, and in so doing has covered the production of an auriferous pyrite concentrate. The present paper deals with the recovery of gold by cyanidation from that concentrate. This gold, though intimately associated with the pyrite, can, for metallurgical purposes, be considered as all occuring in the native state.

Jan 1, 1946

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By J. Visman

The water cyclone washer has a number of advantages that makes it a desirable machine for the cleaning of fine-grained and friable materials such as 1,4 x 0" slack coals. In this paper results are presented of tests carried out on a shaly coal containing a high percentage of inter-grown materials from the Minto area, New Brunswick. The tests were con-ducted in the pilot plant of the Western Regional Laboratory in Edmonton. The test results show that the cleaning characteristics of this coal can be improved by lightly grinding the recirculating middlings fraction, which constitutes approximately 30 per cent (1.45-2.00 fraction) of the raw feed. • The cleaning of 1;4 x 0" fines by water cyclones compares favourably with other coal cleaning machines and has an added advantage of being extremely simple to operate, low in capital and operating cost, and high in capacity. The application of water cy-clones dates back approximately ten years, following its development at the Dutch State Mines. ( 3) A number of papers published d

Jan 1, 1961

By W. J. Farley

Location and History The Sherritt Gordon mine is in northern Manitoba, one hundred miles north of The Pas and forty miles northeast of Flin Flon. The original discovery was made by a Cree indian, Philip Sherlett, in 1922. The claims lapsed in 1924 to be re-staked and optioned by various mining groups who carried out a certain amount of development work before relinquishing their options. In 1927 the present Company, Sherritt Gordon Mines, Limited, was formed to take over the property. Production commenced in 1931, but in the following year operations were suspended and it was not until 1937 that the prevailing price of copper pemitted resumption as an economic operation. The mine has operated continuously from that time to the present. Total production to the end of 1947 has been: Copper . . . . . . . . . 301,813 . .,345 pounds Zinc . . . . . . . . . . . 112,636 tons of concentrat (50% zinc) Gold . . . . . . . . . . 83,070 ounces Silver . . . . . . . . . 2,651,317 ounces General Geology The consolidated rocks in the vicinity of the mine, all of Precambrian age, are a series of gneisses and form a part of a great area of what are known as the Kisseynew gneisses. The Sherritt is the only known economic base-metal deposit to occur within the Kisseynew series. Extreme metamorphism has produced recrystallization that has imparted a decided igneous-like texture to many of the units. However, the gneisses are predominantly of sedimentary original although the most basic member, a hornblendegarnet gneiss, is considered to be an altered basic flow. Figure 1 illustrates the intricately folded structure and the succession of roe types. The footwall enclosing members are of sedimentary origin and represent quartzite and arkosic and greywacke derivatives. The contact footwall member is gneissic quartzite, a medium to coarse grained rock composed mainly of quartz with minor altered feldspar (orthoclase and plagioclase), muscovite, chloritized biotite, and magnetite. Most phases of this unit show varying degrees of granitization.

Jan 1, 1949