Search Documents

By Leon J. Perrier

The paper describes the equipment in use, haulage grades, road conditions, tire sizes, tire performance and related problems. Various types of failures and causes, corrective action taken, tire records and reporting for control are also discussed.

Jan 1, 1977

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By A. P. E. Dirige

Extensive field study has been performed to assess the capabilities of thin sprayon liners (TSLs) and conventional spray-on support systems for preventing rock and support material damage that often results due to mining-induced rockbursts. Support performance was studied using field scale explosive detonation trials to simulate dynamic failure effects that are known to develop during typical rockburst events. Multiple seismic and high speed photographic monitoring techniques were used to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion, and support liner survivability characteristics. Results of this study have demonstrated that TSL?s and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In this study, field results have been verified using numerical modeling procedures to better understand the support behaviour of TSLs when subjected to highly stressed mine environments and mining-induced rockbursts, a factor that is essential when designing any rock support system. A series of numerical modeling assessments were conducted using FLAC3D modeling of a half circular TSL-lined tunnel, influenced by anisotropic stresses and simulated mining-induced rockbursts, to investigate the support potential of TSLs under prototype conditions. The effect of a mine rockburst was simulated using the three-dimensional dynamic analysis option of FLAC3D. Results of TSL-lined tunnels in highly stressed and mine rockburst conditions indicated exceptional effectiveness of TSLs for suppressing rock deterioration resulting from stresses and rockbursts. The rock support potential of TSLs on tunnel surfaces was compared with that of thin shotcrete linings, and results indicated that thin spray-on lining products currently available may be equally as effective in support as shotcrete materials.

May 1, 2009

By R. W. Nice

"The Similkameen Mining Company property is situated about 9 1/2 miles south and west of Princeton B.C. Owned and operated by Newmont Mining Corporation, mining is presently taking place in the Ingerbelle pit. At 15,000 tpd of 0.50% Cu ore the Ingerbelle pit is sufficient for about 8 years. Another 8 years ore supply is available from the old Granby workings of the Copper Mountain property which operated from 1927 to 1957.The pit operations commenced in late 1970 with the concentrator starting in March 1972. Designed and built by Bechtel Corporation under the supervision of Newmont the concentrator's design was based on single-stage crushing and single-stage modified autogenous grinding. The modification was installation of a crusher to crush the critical size build-up. The description of the operation follows.CRUSHERThe primary crusher is an open pocket Allis-Chalmers. 54"" x 74"" gyratory. The basic closed side setting is 8"". The crusher is fed from one side with 100 ton Electra-haul trucks. The crusher pocket discharges to a 96"" wide conveyor belt, then to a 48"" conveyor system including a stacker belt. The crushed product is piled on a stockpile with a capacity of about 30,000 live tons. This stockpile feeds the concentrator."

Jan 1, 1975

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By W. E. Oching, M. M. Ghomshei

Attracting and retaining workers in mining industry has become an uphill battle to many mining companies. As workers with significant experience retire, it is getting more difficult to attract not only new workers but also top talent to the mining industry to replace professionals exiting the workforce. To make matters worse, students’ enrolment in the post-secondary mining programs in Canada and USA is continuously declining year after year for reasons not directly linked to job market. This raises a question of how can the future needs of mining be met? This paper focuses on avenues for collaboration of industry and educational institutions to meet the current and future needs of mining. It provides effective approaches that mining institutes can engage with program advisory committees, role of the mining industry in supporting both faculty and students, how to harness the benefits of diverse workforce in the country and use of innovative technologies to attract young workers in mining. This work presents Human Resources (HR) professionals with tools that they can use to hire and retain skilled workers with strong interest to work in the mining industry. It also provides HR professionals with an opportunity to re-evaluate their restructuring practices during economic downturns as they reduce number of employees on temporary or permanent basis. The paper stresses the need of working together of the mining stakeholders including mining industry, academic institutions, First Nations’ communities and provincial(state) and federal governments to meet the current and future demands of mining as the industry experiences shortage of labour and low students’ enrolment in post-secondary mining programs. It is shown that mining educational institutes can enhance their programs and recruitments through establishing a better communication with all stakeholders. This communication can be facilitated by creating a national advisory board, to work with all mining programs at the national level for sustainable mining.

Jan 1, 2023

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

"The Key Lake mill was commissioned in 1983 to process the two Key Lake ore deposits. With the depletion of these ore bodies in 1999, the plant was converted to mill the exceptionally rich McArthur River deposit located seventy eight kilometers northeast of the Key Lake mine site. This paper describes in detail the Key Lake milling process. The mill consists of a grinding circuit, a leachkounter current decantation circuit, a solvent extraction circuit, a yellowcake precipitatiodcalciner circuit, an ammonium sulphate crystallization circuit, and a waste treatment circuit. The paper also describes process changes to handle McArthur River ore, including the ore receiving stationLOCATIONThe Key Lake mill is located 78 kilometres south of the McArthur River mine. It is located at latitude 57' N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pine House, located 240 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYAND DESCRIPTION OF OPERATIONThe Key Lake mill was commissioned in October 1983 to process ore from the Gaertner and Deilmann ore bodies. The mill was designed to produce twelve million pounds of uranium oxide (U308) a year from a feed grade of 2.4% U3O8.Following grinding, the uranium is leached in a two stage leach circuit using oxygen and sulphuric acid. An eight-thickener counter current decantation (CCD) circuit is used to separate the uranium bearing solution from the solid waste residue. The uranium is further purified in a solvent extraction circuit and then precipitated using ammonia. It is then calcined at 840' Celsius, and packaged into drums for shipping to refineries. There is a crystallization circuit to recover ammonium sulphate produced in the process and a waste treatment circuit."

Jan 1, 2001

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By C. Carlson, W. Muir

"The oxygen demand of the complex lead-zinc-iron feed at the Cyuro Anvil concentrator was determined denendent on the cyanide ion con-contration of the pulp. By redistribution of the cyanide [ ] the grinding circuit in direct proportion to the amount of surface area created, a more activated flotation feed in obtained.Monitoring the oxygen demand of the flotation feed and grinding mill discharge has proved useful in diagnosing metallurgical problems day to day operation."

Jan 1, 1976

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004

By F. G. Pickard

"The Strathcona Concentrator is one of three concentrators presently operated in the Sudbury District by the Nickel Division of Falconbridge Nickel Mines Limited. Production commenced in 1968 at a milling rate of 6,300 tons per operating day. Milling capacity was increased in 1970 to 7,200 tons per operating day. 7he ore contains iron, nickel and copper primarily in the form of pyrrhotite, pentlandite and chalcopyrite, while the common gangue minerals are feldspar, quartz, mica, talc and chlorite. The primary function of the concentrators is not only to liberate sulphides from silicate gangue minerals but also to separate pyrrhotite from the more valuable minerals pentlandite and chalcopyrite.SummaryExcessive wear on steel liners and blinding of grates in a regrind pebble mill of the Hardy Concentrator was corrected by the use of rubber liners and grates. The success of these resulted in their installation as original linings In all grinding units except the rod mills at the Strathcona Concentrator. The operation of rubber liners and grates when sized mine ore was used as the grinding medium was satisfactory confirming the Hardy Concentrator experience. Problems developed when the grinding medium was changed from sized mine ore to steel balls in that blinding of the grates occurred. This resulted in conversion of the units to overflow type mills through removal of the grates. The lifter bar life was significantly increased by using higher lifter bars.Grinding PracticeOperation of a regrind pebble mill commenced in 1961 in the Hardy Concentrator. This operation demonstrated the economic feasibility of using sized mine ore as grinding medium. Problems caused by excessive wear of metal liners and grates combined with blinding of the grates were corrected in 1964 through installation of rubber liners and grates."

Jan 1, 1974