Search Documents

By Chang TS, Suzuki K, Go H, Nakamura S, Kuwano Y

In 1979, a test operation of an experimental blast furnace was carried out to investigate the behavior of a sort of formed coke, which was used safely by 30% of total coke charge in No.2 B.F., Sakai works, NSC, in 1975". The Mashec-type formed coke of 60 x 60 x 40 mm in dimension was crushed and screened so that it had the same size range (1011,20 mm) as ordinary coke used in the base operation. Preceding to the operation, some experiments on the properties of the formed coke and the effects of crushing on them were performed.

Jan 1, 1981

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

By W A. Ducker, R-H Yoon, M Mao

Froth flotation relies on an attractive force between a particle and a bubble to selectively extract particles from a mixture. The range and magnitude of this attractive force is an area of ongoing investigation. We describe measurements of the effect of dissolved gases on the long-range attractive surface forces between a silica plate and a glass sphere in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions. The measurements follow on the work of Sakamoto et al (2002) who have concluded that long-range interactions occur in air-equilibrated surfactant solutions but not in degassed solutions. In the present work, we have measured attractive forces that have a much larger in magnitude than the expected van der Waals force in solutions that were degassed by the same procedure used by Sakamoto et al (2002). We find that the forces are most attractive at 5 + 10-6 M C18TACl, which is close to the charge compensation point (ccp) of the glass sphere. At this concentration, the attractive force decays exponentially with distance and the decay length is 34 in air-saturated solution, and 38 nm in degassed solutions. In both air-equilibrated and degassed solution, the force is quite sensitive to the concentration of surfactant. The force is also sensitive to the pH. We note that our degassing procedure increases the pH of the solution from about 5.7 to 6.6 (presumably by removal of dissolved CO2). We find that the forces measured in degassed solution can be reproduced by using a solution that was equilibrated in air, then the pH was increased by addition of NaOH. Therefore, we conclude that the main effect of degassing in our experiments is to raise the pH. We show that the range and magnitude of the attractive force decreases in the presence of salt (NaCl). This suggests an electrostatic mechanism for the attraction. Possible mechanisms for the attractive force are examined, including the mechanisms that rely on a patchy coverage of surfactant on the silica surface.

Jan 1, 2005

By Kellerwessel H, Oberheuser

Since its invention by Professor Klaus Schonert of the University of Clausthal, Germany, high pressure rolls comminution has attained near total acceptance as the preferred method of size reduction in the cement industry. Over 300 units have been manufactured worldwide. At locations where the system has been installed, considerable energy savings have been realised. These energy savings are generally in the range of 20 to 30 per cent compared to conventional ball mill circuits. However up to 50 per cent power saving has been achieved at some installations. This technology, with the exception of the diamond industry, has up to now had only limited success in ore processing. This has mainly been attributable to the abrasiveness of ores encountered in this industry leading to high wear rates. These high wear rates have given rise to an unacceptably short life time of the wear surface of the rolls, requiring regular replacement. A new wear surface has been developed which has shown to give a ten-fold increase in service life over conventional surfaces. This, together with developments made in machine design now give the units the ability to attain the high availabilities demanded by the mining industry, and therefore to allow this industry to achieve the considerable operating cost savings offered by the high pressure rolls.

Jan 1, 1992

By A Kindred

The Bogong Hydropower Development is a 140 MW high head power project currently under construction in Northern Victoria. The project is the final link in the Kiewa hydroelectricity scheme, which was originally constructed in the 1950s. Due to its location in the Alpine National Park, the waterway for the Bogong project must be located entirely underground. A series of shafts and tunnels is being constructed to transfer the water from the headworks at McKay Creek to the new power station located on the shores of Lake Guy in Bogong village. The difference in elevation between the headworks and the power station is greater than 420 m, which poses particular issues for the design and construction of the waterway. The purpose of this paper is to describe the design and construction planning aspects of the tunnelling and shaft excavation and lining works for the waterway. The tunnelling works includes 5.7 km of hard rock tunnel boring machine (TBM) driven tunnel, 1.1 km of drill and blast tunnel and two deep shafts. The tunnels and shafts are lined with a mixture of permanent rock bolts and shotcrete, concrete lining and steel lining. The viability of the Bogong Hydropower Development relies heavily on the ability of the TBM to excavate at high speed through the East Kiewa Grandiorites. Particular attention was given during the construction planning stage to understanding the excavation characteristics of this material, and designing a suitable hard rock TBM that would be capable of meeting the program requirements of the project.

Jan 1, 2008

By J C. Diaz, C R. Scherpenisse

Blasting represents one of the most relevant unit operations in the process of mineral extraction. The final objective of this operation is that of obtaining an adequate final fragment size distribution such that the combined costs of drilling, blasting, excavation and transport, and crushing/grinding, are minimised, while at the same time producing the minimum possible level of damage to the surrounding rock mass. The strong influence that drilling and blasting has over the subsequent processes involved in the operational cycle makes it imminently desirable to have access to experience and technology which make possible the evaluation and optimisation of this unit operation. The correct use of vibration monitoring techniques offers a number of benefits in terms of their ability to examine any blasting process in detail. In effect, the measurement of particle velocity levels that result from the detonation of each explosive charge offers a means by which it is possible to measure relative efficiency of each charge, interactions (productive and counterproductive) between adjacent charges, and a definitive indication of general performance of any given blast design and its implementation. In this way the monitoring of blast vibrations in rock due to the blast event, can be used as a diagnostic tool, given that the correct interpretation of the vibration traces allows the determination of the level of interaction between the design and operational variables of the blast event. This makes it possible to evaluate, for example, the presence of out of sequence detonations, statistical scatter in the detonation times of pyrotechnic delay detonators, deficient detonation of charges, instantaneous detonation of charges and sympathetic detonation of charges, as well as the general of vibration levels in terms of peak particle velocity, acceleration, and displacement. Another important use of such data is in the construction of a database relating vibration levels to charge weight, hole diameter, and distance, for any given rock type, enables the calibration of predictive vibration models which in turn make it possible to predict the damaging effects of blasting. Knowledge of both the vibration levels induced, combined with quantitative measures of the geomechanical competence of a rock mass make it possible to estimate the probability of producing blast induced damage. The high levels of vibration generated by some blast events may damage the rock mass, producing new fractures or extending and dilating existing fractures. The vibration in this context may be considered as a dynamic stress provoking strain in the rock mass. This paper describes the application of the vibration monitoring technique, particularly in the underground mining environment, and its importance in diagnosis, modelling, control, and optimisation of the development blasting process. The potential of the technique is assessed in the context of achieving substantial techno-economic improvements development blasting results, increasing output whilst minimising the operational costs of the mining process.

Jan 1, 1999

By Pollmans GJ, Hoberg H, Schneider FU

The Institute of Mineral Processing at Aachen University of Technology has been engaged in fine and ultrafine comminution for several years. Former investigations had been dealing with the mechanical activation with the aim of increasing the solubility of highly resistant oxides such as tantalite and niobite while research on the product of ultrafine powders is of major importance at the moment. Materials of that kind are of increasing interest in the production of extremely resistant ceramics, in the development of new raw materials, in powder metallurgy and in the production of fillers (extender pigments) and pigments. The creation of ultrafine powders is difficult and very expensive. They can be produced by means of condensation or dispersion methods. One important method of dispersion is mechanical comminution. Due to long and intensive research and development all over the world important advances have been achieved but still a great number of questions and problems occur especially in producing materials of submicron and nanometer grain sizes which could be answered or solved only insufficiently up to now. These mentioned difficulties refer especially to: ò the required energy input into the feed material, ò the forming of strong agglomerates and wall stickings, ò the required product qualities, and ò the entire and reliable characterisation of the products. Basic investigation aim to clarify the micro and macro processes of ultrafine grinding and work towards solutions to the difficulties mentioned above. The aim of the Institute's research is the development of a new grinding device for producing ultrafine powders. First results of a laboratory scale mill of that type will be presented in this paper.

Jan 1, 1993

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

Copper entering a lead ,smelter in concentrate or from other sources is recoVered as matte and speiss which contain appreciable quantities of lead. The matte and speiss are usually sold to copper smelters to recover the copper content and also any gold and silver in these products, but the value of the lead is largely lost. Some copper plants pay for portion of the lead content, but regarded as a means of recovering lead it is more costly and less efficient than if the lead were recovered at the lead smelter.Because of the value of this lead loss, the metallurgy of copper recovery has assumed greater importance in recent years owing to the rise on the price of lead.Two processes are in use today to produce matte and speiss, namely the iron matte process and the soda matte process developed by the American Smelting and Refining Co. 1 in D.S.A. The latter process is characterised by a higher copper to lead ratio than the older iron matting process.The following analyses are typical of matte and speiss produced at Broken Hill Associated Smelters, by both processes, although the soda matte process is still in a developmental stage and experience indicates that matte and speiss of lower lead tenor can be produced under favourable conditions.

Jan 1, 1951

By Brett D

Tailings disposal and water management are one of the most important environmental issues in mining projects. The nature and the method of disposal of the tailings will determine the long term environmental impacts and must be carefully considered at the planning stage so that final abandonment can be economically achieved. If not, long term and on-going treatment and amelioration may be required to achieve environmental standards. Final abandonment requires dam safety surveillance inspection to satisfy engineering stability and hazard requirements as well as environmental issues. Environmental issues include stability, as well as rehabilitation and long term contamination potential.

Jan 1, 1991

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

The treatment of nickel ores and concentrates and the subsequent processing to recover separate products of nickel and cobalt is one of the major interests at present in the mining industry. The increasing demand for nickel, and more recently also cobalt, has led to increased exploration for ore sources. Major discoveries have resulted in Canada and Australia. These deposits, as well as others already known, are presently being developed and the process technology tested and evaluated for applicability to the different mineralogical types - mainly sulphide, arsenide and oxide laterites. Concentrates may be treated by either hydro- or pyrometallurgical processes, while the nickel laterites are best suited to hydrometallurgical processing. However, if hydrometallurgy is used, once the ore or concentrate is leached the resultant solutions are then amenable to similar separation technologies for purification and recovery of high purity nickel and cobalt products. Solvent extraction, together with other separation processes such as precipitation, can produce high purity solutions of nickel and cobalt. The final products of these solutions may be nickel and cobalt cathodes, metal powders precipitates or salts, depending on the final process of electrowinning, hydrogen reduction, precipitation, or crystallisation Respectively.

Jan 1, 1996

By A Tomsett, R Kidd, Z Casley

Bivariate recoverable resource estimation aims at predicting the recovered metal for a secondary variable when a cut-off is applied to a primary variable. The choice of a consistent geostatistical model is advisable to allow a robust estimation from exploration data of the primary and secondary metal recovery functions on a generic selection block (selective mining unit û SMU) within large panels. Ore processing decisions at Lihir Gold LimitedÆs Lihir Gold Mine are based on the gold and sulfur estimates of SMUs from production (grade control) data. The predictive model from exploration data at Lihir is based on the estimation of a recoverable resource for gold by Uniform Conditioning (UC), with an estimate of the sulfur grade being provided by Ordinary Kriging of panels. While univariate UC is adapted to the diffusive nature of the gold mineralisation (Ladolam orebody) at Lihir, the independent estimation of sulfur, through ordinary kriging, fails to capture the potential spatial correlation that exists between gold and sulfur mineralisation. This paper presents a practical implementation of bivariate UC, which better represents in the resource model the spatial correlation between gold and sulfur. Incremental economic gains through improved definition of material categories and scheduling are investigated, and the particular impact on the process of geological interpretation and domaining is emphasised.

Jan 1, 2009

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By Horowitz F. G, Lamb P

As mining operations become larger and more complex, larger volumes of geological, geophysical, and production data must be manipulated and interpreted on a day-to-day basis. Because of the large volume of data, more sophisticated data storage strategies, interpretation tools, and visualisation tools must be used by exploration and mining operations in order to remain competitive. Critical to better practice is an understanding of the basic syntax and character of geological and mining data, expressed in the form of a data model. In the short-term, a data model can be used to implement or evaluate schemes for data storage or exchange. It can be used to evaluate software. In the longer term, a data model is essential to the design of the next generation of software for 3D geological modelling. In this and the related paper (Lin et al, 1995) the data model in use by CSIRO is presented, together with: 1. examples of the use of data transfer in the linkage of existing mining software; and 2. examples of the use of the data model in software design.

Jan 1, 1995

By Wilkinson RDB, Van Der Meer FP

In order to overcome the statistical limitations imposed by the need to recover density tracers by hand, magnetic density tracers were developed to determine the efficiency of dense medium separators treating porous materials. The tracers were manufactured by extrusion of polypropylene ferrosilicon mixtures and subsequently coated with a distinctive paint to allow hand sorting according to density. Fifteen tracer batches were manufactured in the range 1.61 - 1.94 g/cm3. The tracer densities were determined by a hydrostatic method. The tracer method was applied to the dense medium separation of a Moroccan oil shale in a pilot scale Dyna Whirlpool separator. For each test, about 20,000 tracers were added with the plant feed and subsequently recovered from the products with a dry low intensity magnetic separator. The Tromp curve determined by conventional heavy liquid analysis was displaced towards lower densities compared with that determined by tracers, indicating that the porous shale particles absorb heavy liquid. It is concluded that for porous materials like oil shale and coal, the tracer method gives the most accurate results. In pilot scale testwork the tracer method is also much faster than the conventional heavy liquid analysis, as rather large samples have to be processed by the latter method to ensure Representativeness.

Jan 1, 1987

By W L. Lane, T R. Yanske

The Doe Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 m in height and the use of slinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction becoming a major portion of the overall production and have added to the mine life of Doe RunÆs six operating mines.

Jan 1, 1998