Search Documents

By Walton S, Wheeler D. J, Sargent D. M, Ting L. Y

Goonyella-Riverside mine is an open cut coal mine in Central Queensland. One component of the mining operations at this site is an uncompacted spoil dump some 50 m above the natural ground surface and over 300 ha in extent formed as a result of bucket wheel excavator operations. Plateau area slopes are 0.5¦ to 1.5¦ with irregular outer dump slopes of 9.5¦ - 17¦Investigation was undertaken and a series of trials planned to assess the suitability of a variety of stabilisation proposals to meet the client's requirements and to conform with Department of Resource Industrystabilisation guidelines.

Jan 1, 1992

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

A review is presented of techniques cur- rently in use, or being developed, to enable the determination of virgin rock stress at consid- erable depth (> 1000 m) from small diameter sur- face drill holes (

Jan 1, 1975

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Shugen T

Due to the increase of passenger traffic, a new station is proposed which is about 6.8km from south station. An underground connection line is under feasibility study for connecting these two stations in order to avoid the in- terference with surface traffic. In this paper the traffic condi- tion and the geological formation along the planned route will be described and analysed. Different methods of con struction have been proposed and dis- cussed such as shield method, slurry wall method etc. In this paper compari- sons are made among these methods and advantages and disadvantages given. The authors proposal to construct this connection line by NATM raise wide

Jan 1, 1987

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

By Roberts M. L

Long Shaft was initially developed using a rail haulage system on every working level comprising battery electric locomotives and granby trucks loaded by rail mounted rocker shovels. Production was commenced using conventional hand held cut and fill mining methods. In an effort to improve productivity and reduce operating costs a mechanised cut and fill stoping method evolved to suit the wider sections of the orebody. To further improve productivity and reduce costs the mechanised levels of the mine are progressively being redeveloped to enable the use of trackless diesel haulage equipment. An added benefit of trackless haulage equipment will be the ability to place development mullock into stopes as Fill.

Jan 1, 1988

Estimation of the semi-variogram is basic to the geostatistical processing of data. The most widely used arithmetic average estimator is here employed with various sampling patterns to calculate experimental semi-variograms in a deposit which is simulated to have a defined semi-variogram. Percentage differences between theoretical and experimental semi-variograms are reported.

Jan 1, 1984

By Alesse V, Belardi G

A new class of collectors, Mercapto-Benzo-Oxazoles (MBO), exerting selective action on copper sulphides in the presence of Pb, Zn and Fe sulphides (galena, sphalerite and pyrite), has been synthesised in co-operation with Enichem's Donegani Insitute. The collectors have a mixed aliphatic-aromatic structure and contain functional groups which form chelates with copper. Some reagents of this class having hydrocarbon chains of various lengths have been laboratory tested on a complex sulphide ore containing chalcopyrite, galena and sphalerite in pyritic gangue. Comparative flotation tests have permitted selection of the best collector for chalcopyrite, namely Methyl-Mercapto- Benzoxazole (MMBO). Systematic flotation tests have been performed with this reagent, varying collector concentration, grain size of the feed, pH and flotation time. The results obtained show that the synthesised collector is much better than potassium-amylxanthate (KAX) as regards selectivity towards Pb and Zn. Moreover, it is possible to work at natural pH (6-7) and the flotation rate is higher. In fact in the rougher stage with 80 g/t of collector at natural pH, a copper grade of 7.14 per cent was obtained with a recovery of 73.87 per cent, while the grade with KAX did not exceed 2.11 per cent for a recovery of 73.54 per cent. The amount of Pb and Zn reporting in the copper concentrate was eight per cent and ten per cent respectively, while with KAX it was no lower than 24.34 per cent and 22.71 per cent in that order. After two minutes flotation a copper grade of 5.2 per cent with 52 per cent recovery could be attained, against a grade of 2.5 per cent and a recovery of 44 per cent in the case of KAX. The efficiency of this new collector has been ascertained on two samples of complex sulphide ores of diverse mineralogical composition.

Jan 1, 1993

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

The future of the Tasmanian mineral industry can only be estimated from a knowledge of the past, and armed with this knowledge an orderly plan for the future can be developed. Brief mention is made of the major historical developments through to the present day, with past and future development areas clearly mapped. Areas of importance which have been discussed are divided into the mining of metals, fossil fuels and non-metals; and the process- ing and extractive industries. Discussion then follows on the current general non-insular pressures on the mining industry, the energy crisis, scrap, world shortages, new techniques, inflation, and the effects of exploration on the environment. This is then followed by a discussion of the advantages of Tasmania as a mining state and a cataloguing of the present exploration and some possible areas of future development. From this a suggested plan emerges for the future development of the Tasmanian mineral industry, to incorporate the latest technological advances and by planning to meet the challenge of survival and growth in a turbulent environment.

Jan 1, 1977

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

Drilling and blasting operations have historically been viewed as a necessary 'evil' part of mining, whose costs should be minimised by whatever means possible. In the past, when operations depended primarily on crushing and milling for ore re

Jan 1, 1998

Zircon is extensively used as moulding sand in the production of steel and high-duty iron castings. To achieve a satisfactory grade of zircon concentrate, the zircon particles may need ,to have surface coatings removed, as such coatings can hinder electrostatic and magnetic separation of zircon from associated minerals. Xn addition the presence of surface coatings on the zircon. particles can cause sinterins and fusion of the zircon to the east metal resulting in "burnt-on" sand or fritting of the casting. "Burnon" necessitates cleaning of the casting by grinding or chipping, which is expensive and results in loss of definition on the casting face.Hudson (1966) has pointed out ,that some coatings on mineral sands are lightly-adhering clays which can be removed quite readily by agitating the sands in water for a few minutes-thus their removal constitutesno problem. However, the heavy gingery coloured coating which adheres strongly to the surface of the particles in some deposits, and which has generally been considered to be a form of iron oxide (Baker, 1962; Hudson, 1966), cannot be removed effectively by attrition cleaning in water (Hudson, 1966). Such coatings limit the usefulness of these concentrates in the foundry industry.An investigation of strongly-adhering coatings on "ginger zircon" concentrates from the Yoganup deposit of Westralian Sands Ltd has shown that the stain consists of a cemented mixtvre of hydrated iron and aluminium oxides and kaolin minerals, and that it can be removed by a relatively low cost treatment.IDENTIFICATION OF THE STAIN BY XRDX-ray powder diffraction (XRD) patterns were obtained from small samples of stain scraped, individually, from the surface of hand-picked zircon and ilmenite crystals. These scrapings were mounted on quartz fibres and exposed to CoKa radiation in a 57 mm Debye camera. To avoid heavy fogging of the x-ray films, a substantial amount of the iron oxides was preferentially leached from the scrapings (before mounting) with an ammonium oxalate-oxalic acid solution (Rooksby, 1961). The residual material gave a fairly well resolved powder pattern (Table 1). A...

Jan 1, 1975

By Hungerford F

Long-hole drilling technology has rapidly advanced this decade beginning with rotary drilling/pump down camera surveying and culminating in down-hole motor drilling with cableless electronic surveying over the past two years. With the latter system, a high level of directional control is achievable in boreholes up to 1000m long. Past long-hole drilling across the industry has seen a mixture of success and failure. With these experiences, new and improved techniques and equipment have evolved. A number of long-hole drilling options are available as variations on the basic rotary and down-hole motor methods. They involve different levels of cost and equipment and vary in their suitability in different geological environments and definition of targets. Long-hole drilling is mainly target applied, either in defining geological structures in greater detail, or proving important mining areas such as longwall blocks, to be free of structures. Successful drilling hinges on a combination of drilling expertise, quality and appropriateness of equipment, understanding of geological conditions and good colliery support. Drilling expertise forms part of sound interpretation through keeping relevant records, understanding the reasons for changes in drilling conditions and implementing specific tests such as coring. The final interpretation builds upon all other available geological information. There is still scope for research into improved techniques and equipment. The use of long boreholes for geophysical surveys has high potential.

Jan 1, 1988

By R Castroviejo, F Segundo, C Brea, J-C Catalina, H-J Bernhardt

Optical microscopy is a basic but still indispensable tool for examining mineral parageneses in ores. The design and concepts behind the reflected light ore microscope have obviously not been subject to spectacular technical evolutions in the last decades. However, digital imaging capabilities have opened new and stimulating perspectives for automated mineral identification. Recent works in developing multispectral image analysis (Pirard, 2004) have demonstrated its superior potential with respect to conventional colour imaging, but at the same time reconciliation with spectroscopic databases such as the Quantitative Data File III (Criddle and Stanley, 1993) still needs a more in-depth investigation as well as the possibility to extend both imaging and spectroscopy into the near infrared domain. In this paper, the authors present results gained from multispectral imaging in the range between 400 and 1000 nm together with spectrophotometric data from the QDFIII database, with an emphasis on minerals that cannot be easily distinguished in the visible spectrum.

Jan 1, 2008

By D Akis, A Clark

The Lihir gold operation, located in the New Ireland Province of Papua New Guinea (PNG), approximately 900 km north of Port Moresby, was commissioned in 1997 under the management of the Lihir Management Company, a subsidiary of Rio Tinto. This management period ended in 2005 with Lihir Gold Limited (LGL) becoming self-managed. LGL is now the largest listed company in PNG and a top tier mining company in Australia. The focus of the operation since 2005 has been to take advantage of strong market conditions to increase cash flow while driving operating costs into the lowest quartile of gold producers. During this period production has increased through capital expansions, most notably with the addition of a flotation circuit, and through culture change and efficiency improvements. The next step forward for the Lihir operation is a major plant upgrade to increase production to an average of around one million ounces per annum by matching the ore processing rate to the ore mining rate. The key benefits of this project will be the addition of approximately 240 000 ounces per annum of gold production, the access to an additional one million ounces of gold and the ability to meet all stockpiling requirements. The Lihir operation has come out of the boom period in a strong position, is undertaking a major upgrade at a time when prices are low and labour is available, and will be positioned to take advantage of future opportunities as they arise.

Jan 1, 2009

By Mullens P

Recent advances in technology have allowed many of the problems of directional control of long diamond drill holes to be overcome. Three case histories are presented, from Cobar, Hilton North and Mount Isa Mine, in which careful hole design and the use of wedges and down-the-hole motors have allowed tight directional control of drilling. Substantial savings in time and cost were achieved in all three cases.

Jan 1, 1990

The techniques used by the State Electricity Commis- sion of Victoria to handle and store brown coal in the both the raw coal and boiler bunkers are outlined. These tech- niques were adopted in agreement with the science of modern bulk solids handling. By successful balance between practical requirements and bulk solid handling system design require- ments the Commission expects to confidently attain reliable coal flow even for the most adverse of coal flow properties. Attainment of this goal demanded full attention to channel detail selection. An outcome of this attention has been the development of a novel bunker and discharge arrangement for handling extremely difficult to handle coals. Due to the novel features of this slot bunker outlet arrangement it's ad- vantages and disadvantages are discussed.

Jan 1, 1987