Search Documents

By D Gerrard, J Begelhole, J Gerber

The Iron Magnet deposit has been mined since 2007 when Arrium (then OneSteel) commissioned the magnetite concentrator to supply feed to the pelletising plant in Whyalla. The concentrate quality requirement for the customer required consistent product with minimal variability. In the early stages of operation, it was identified that the feed variability introduced significant changes in the concentrate quality, which was outside the acceptable customer limits.In 2011, a geometallurgical regression model was developed that allowed for the estimation of concentrate quality produced from the feed material. This was based on a laboratory-scale Davis Tube Recovery (DTR) test performed on the feed material. The objective of the project was to characterise the raw ore in the pit to allow for blending prior to crushing. By blending the feed to the concentrator, minimal concentrate quality variation within the plant was achieved. The orebody was divided into geometallurgical classes, called ore types, based on the mineral texture and magnetic mass recovery. Each geometallurgical class consisted of material with similar metallurgical performances. For each individual blast pattern, the ore was grouped into the geometallurgical classes and a composite sample was created. The composite sample was put through the laboratory-scale DTR test and the results were used to estimate the metallurgical performance of the material.The characterisation process and feed pile build methodology was applied in early 2013 and went through an optimisation and streamlining phase. Since the implementation of the geometallurgical characterisation process, the plant has seen a significant reduction in concentrate variability and measurable throughput gains. The characterisation process has also increased the amount of material that is now classified as ore.CITATION:Gerber, J, Gerrard, D and Begelhole, J, 2015. Geometallurgy of the South Middleback Ranges magnetite deposit – predicting plant performance from the pit, in Proceedings Iron Ore 2015, pp 555–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By G Collecutt, D Proud, D Humphreys

"The hazards associated with dust explosions are well known, and coal dust explosions present a significant hazard in the underground coal mining industry worldwide. In earlier work, we presented computational fluid dynamics (CFD) simulations and test results for coal dust explosions within a 2.5 m diameter circular gallery, along with CFD simulations and test results for the suppression of these explosions with finely atomised water sprays. In this paper, we present refinements to the CFD modelling that yield a significantly improved calibration with the test results, and proceed to investigate by CFD the requirements for suppression of a coal dust explosion in a typical underground roadway. This work was carried out under an ACARP project and we gratefully acknowledge their assistance. CITATION: Proud, D, Collecutt, G and Humphreys, D, 2015. Computational fluid dynamics modelling of coal dust explosions and suppression systems, in Proceedings The Australian Mine Ventilation Conference, pp 309–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By M Haest, O Dominguez, D Mittrup

Technological innovations and emerging analytical capabilities are transforming the way drill samples are analysed, with real-time mineralogical analysis made possible. In addition, new business/technical requirements are challenging long standing processes to incorporate more sources of information during planning in order to improve compliance to plan during mining and processing. Unfortunately, the new sources of information that are added do not always have adequate protocols in place to ensure quality data is collected.Spectral data covering the visible – near – short wave – midwave – longwave range are routinely collected by the Geoscience and Exploration department at BHP Billiton Iron Ore for accurate mineralogical identification. These data are used for geological interpretations (logging and modelling) and prediction of physical variables (metallurgical and geotechnical properties).This paper introduces how sampling and quality assurance / quality control concepts have been applied in the spectral data process. The described routine for sampling, data collection/management and reconciliation has been developed to track system precision and accurately and consistently ensure the data is of high quality before it is used across the mining chain.CITATION:Mittrup, D, Dominguez, O and Haest, M, 2017. A new approach to implement quality assurance and quality control to technological innovations – quality of spectral data capture and processes in the minerals industry, in Proceedings Eighth World Conference on Sampling and Blending , pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By I Douglas, L Allen

Localised indicator kriging was developed following a similar approach used by Marat Abzalov (2006) in his paper titled æLocalised uniform conditioning (LUC): A new approach for direct modelling of small blocksÆ. Abzalov introduced the idea of mapping panel distributions from uniform conditioning onto selective mining unit-sized blocks that were created using ordinary kriging. This concept of remapping panel distributions was applied to multiple indicator kriging histograms.At Newmont a program was developed that made the remapping of MIK histograms to SMU sized blocks extremely efficient and was subsequently tested on several gold deposits. The results have been encouraging as the localised indicator kriging (LIK) method has eliminated many issues that have plagued both ordinary kriging and multiple indicator kriging. Use of localised indicator kriging methodology limits the smearing of high-grade and the over-smoothing of grade that is common and difficult to control in OK but retains the ability for localising grades. LIK also simplifies change-of-support corrections, eliminates un-mineable slivers of low or high-grade when dealing with small tonnages, and allows for the mapping of linear and non-linear estimates into the same block.

Sep 26, 2011

By J Pan

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. The properties of the two types green balls (0.8 per cent bentonite and 2.0 per cent hydrated lime) were as follows: drop numbers of 4.8 - 5.0 times/0.5 m, compressive strength of 19.7 - 24.2 N/pellet and thermal shock temperature of 280° - 385°, respectively, under the same conditions of 1.5 per cent coke, 1.45 basicity and balling at 8.5 per cent moisture for 13 min in disc pelletiser. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8 per cent and climbs up to 3113 N/pellet under the following conditions: preheating at 1050°C for ten minutes and fi ring at 1300°C for 15 min. In the mean time, the hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6 - 70.6 per cent, RDI+3.15+ increased from 90.1 to 98.8 per cent and reduction swelling index dropped from 22.4 - 7.4 per cent, respectively. The mineral compositions and microstructure of fi red pellets shows that the fired pellets containing 2.0 per cent possess more calcium ferrite and magnesium ferrite and compact microstructure, leading to the higher compressive strength.

Jul 11, 2011

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Schwarz, D Alexander

The mining industry, and in fact the world, has undergone significant changes in the past five to ten years, ranging from the metals boom, the global financial crisis and the rise and fall of national economies, to name just a few. There has been a focus on sustainable development for projects and operations in the mining industry, mainly pushed onto the industry by communities, governments and other agencies. While sustainable development and operation is a worthy priority for mining operations, discussions with mining industry personnel (with a strong slant on the mineral processing perspective) have shown other issues have surpassed the typical issues of water resources, energy availability and the environment. These include staff turnover and skills shortages, extracting metal from more complex orebodies and the uptake of new step-change technology.A number of key operating mineral processing personnel were interviewed to determine their perspective on the current issues facing the mining industry. This paper details the findings of this survey and highlights some of the topics that have been identified as the top issues from a mineral processing perspective.CITATION:Schwarz, S and Alexander, D, 2012. Current issues in the mining industry - From the operational mineral processorÆs perspective, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By S Henderson

The Otago Goldfield has produced approximately 8 million ounces of alluvial gold and over 2.5 million ounces of hard rock gold and is currently home to New ZealandÆs largest producing gold mine. In the eyes of explorers this production history makes the goldfield a good place to explore.   Modern exploration in the Otago Goldfield commenced in the late 1970s with the exploration for tungsten. However, a rapid rise of the gold price in the early 1980s saw the focus shift to the exploration for gold which lead to the discovery of the Macraes Gold Project in 1984, which since it came into production in 1990 has been New ZealandÆs largest producing gold mine. With the exception of the Macraes Gold Project, exploration continued in the Otago Goldfield for a further 20 years without further success.   In 2006, Glass Earth (NZ) Limited (Glass Earth) reviewed all the exploration technologies applied to the Otago region and available geological data, including the 1996 OceanaGold Helicopter Electro-Magnetic (HEM) data, and concluded that combined magnetics and HEM were able to delineate the Hyde Macraes Shear Zone (HMSZ) which hosts the Macraes Gold Project. Unlike previous explorers who explored the Otago region in a piecemeal manner, Glass Earth opted to collect a new, region-wide dataset which could be integrated with all previous collected geological information to come up with new exploration concepts and targets. As part of this process, Glass Earth applied in mid 2006 for New ZealandÆs largest on-shore gold Prospecting Permit, PP39-322 which was subsequently granted in November 2006. In mid January 2007, Glass Earth commenced acquisition of approximately 50 000 line kilometres of HEM data, making the Otago regional aerial geophysical survey (survey) the largest aerial geophysical survey ever undertaken in New Zealand.   This paper will report on the progress of the Otago Regional aerial geophysical survey and outline some of the preliminary findings from what is still a work in progress.

Jan 1, 2007

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By T Baumgartl, L Zhou, D Mulligan, L Huang

The rapid production and accumulation of mineral processing wastes in the environment can present serious threats to environmental quality and human health. Phytostabilisation with native plant ecosystems is, in many cases, a preferred option for rehabilitation of mine waste storage facilities. However, much of the literature has focused on species selection in short-term experiments to test their suitability under the often extreme chemical conditions in the wastes without addressing the fundamental requirements – ie hydrogeochemical stabilisation and functional root zones. As a result, successful examples of phytostabilisation of mine wastes such as base metal tailings have been rare, especially if success is defined as meeting the completion criteria of non-polluting and sustainable land system at rehabilitated sites. Conventional capping options to isolate reactive tailings/wastes by using physical break and/or sealing layers are often not reliable in the long term (particularly under semi-arid climatic conditions) and, in many cases, they may not be feasible in the field due to the large areas to be covered and the lack of adequate suitable materials at mine sites. By using sulfidic tailings as an example, we have proposed a new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis in tailings involving accelerated physical, chemical and biological weathering of tailings minerals to achieve hydrogeochemical stabilisation and the development of soil functions, soil horizons and functional root zones.Ecologically engineering functional root zones firstly requires controlling geochemical reactivity in the wastes (ie hydrogeochemical stabilisation), which can cause polluting effects in the root zone and plant toxicity. By means of ecological engineering, in situ weathering of primary minerals (eg pyrites) in tailings may be accelerated by adding functional materials (eg functionalised biochars and organic matter) in the waste slurry during the process of deposition. This will remove or diminish key risk factors (eg potential acidity in tailings and elevated soluble heavy metals) in the solid phase, before placing growth media for reconstructing root zones and transplanting/sowing target plant species. However, much of the acidity, soluble metals/metalloids and other salts would be transported out of the solid phase into the wastewater, which can be addressed by on-site water treatment facilities during mine operation. The trajectory and state of engineered pedogenesis in the weathered tailings may be manipulated to provide specific soil horizons within future root zones that are dynamically evolved toward fully functional soil subsystem within rehabilitated plant ecosystems.CITATION:Huang, L, Baumgartl, T, Zhou, L and Mulligan, D, 2014. The new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis and functional root zones, in Proceedings Life-of-Mine 2014 , pp 663–674 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By J Paradis, K Dudgeon, M Topping

At Newmont’s Jundee Operation, exploration and resource geologists collaborated to produce an open pit resource model. Using a variety of modelling and estimation techniques but no new data, an uneconomic underground target was converted into a potentially economic open pit evaluation. During an industry downturn, it is more important than ever to efficiently share expertise, ideas and resources to problem solve and produce meaningful project outcomes. The two departments brought together different methods and ideas, and the process showed that certain methods worked better than others in different situations, thus the appropriate method was applied to each part of the evaluation. The results were used to create new procedures and improved lithology modelling and resource model estimations. Adaptability of the geology departments and collaboration such as this are key to ongoing improvements and future mine life at Jundee.CITATION:Dudgeon, K, Paradis, J and Topping, M, 2014. Cook open pit model – the hurdles: how we leapt, lunged, stumbled and overcame them, in Proceedings Ninth International Mining Geology Conference 2014 , pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007